I have a 94 Fsuperduty with a flatbed and lift that folds up and stores under the end of the bed. Recently while on a job the lift wouldn't go up, so I checked the one fuse I know of in the system and it was burnt. Put a new one in and before the lift reached the top it burnt-out again. It had been working with no problems for months prior to then.
View 4 RepliesI have a 1994 Black Ford F150 and i was wondering if i could lift the truck 6 inches only using lift blocks (or any other cheap way to get my truck off the ground)....
View 2 RepliesI have a 1994 Ford Explorer XLT. It just died the other night. I have dim dome light, nothing else. I had the battery and alternator tested, both are ok. I get an occasional click when trying to start it. I also get an occasional beeping, the key in the ignition sound. I've checked the fuses, and can't find a broken one.
View 3 RepliesLong story short, my truck's front turn signals and rear turn signals/tail lights won't work. I am thinking that the relay is burnt. Whenever I look in the manual I can't seem to find the location for this relay. Is is built into the flasher?
Also, I am just assuming because the rear turn signals and tail lights are the same bulb that fixing this should clear up both problems. Am I right in thinking that?
I have already checked all of the fuses. Also, the Hazards don't work either.
First off my driver side brake light with stop working. I took it apart to try and find the short. In the process I shorted out all my running lights tail lights and brake lights and turn signals I think also. While I was looking for the short, turn signal wire from my tail light touched the frame and grounded out and that's when all the lights died . My tail lights are some cheap trailer lights without reverse lights. I pulled headlight switch from another Ford truck I have. On the harness connector that connects to the switch which wires should read what when I test with a voltmeter?I checked the fuses in the power distribution box under the hood and they were good. Truck has a flat bed so I don't know if that matters with the wiring, I suspect it's different then a normal bed truck. Wiring on the bed is old, maybe from 94. I am unexperienced with electrical.
View 3 RepliesI purchased a 94 Ford Explorer 4x4 4.0L w/ Automatic transmission with Overdrive. Great work truck, but I am finding that these had a lot of wiring problems. First thing that messed up with me is the backup lights wouldn't work. Then the dash lights and parking lights stopped working (Still no fuses where bad). Then about 2 weeks later, I was on my way home when It just died like someone had turned the switch off, I pulled off the side of the Interstate, and after checking my fuses/Relays under the hood.
I found that the EEC Fuse (30AMP-BIG Fuse) had blowed, I didn't have one and the truck wasn't off the road good, So I wrapped a small wire around the fuse to see if I could start it and get it out of the road better, It started right up, but soon as I pulled it off the road it died again, and I found that it melted the EEC Relay, I went to the parts store and got a new relay and fuse and put them in, It blows the fuse as soon as I put it in, with the switch off or on. I just need to know what things will cause this so I can check them out one by one, until I find the one that is causing this problem, cause It run great up till this happen.
Only other thing I may need to let you know, Is when I bought it, the key switch would start it, The guy had put a push button starter switch that you push to start it with the key on, I unhooked it, and it started fine with the key for a while then it stopped again, so I had to hook the push button back up and had been using it until it stop running with me.
I have a need for a 12-volt signal to indicate the engine is in start or run mode. I would like to pull this from the engine compartment but I'm not sure what would be the best or easiest way to do this. The 12-volt signal is not used to power anything so it will draw very little current. I have a 94 F150.
View 8 RepliesTruck is up in the back country and has quit. It has two factory gas tanks, I can't hear either of the fuel pumps will come on when you turn the switch on. The problem started as an intermittent fuel starvation issue. Truck would act like it ran out of gas then pick up and go again. Switched tanks back and forth but it got worse throughout the day and finally will not start at all. I have listened to both tanks when the ignition switch is turned on but can not hear the pump come on for either tank (switching the selected tank with the switch on the dash). We went through some bumpy terrain just before the problem started so I am thinking maybe a wire might have come loose or got broke somehow. I am asking for wiring schematic so I can check for voltage in the correct place going to the fuel pumps. Both tanks are full of gas so for now dropping either tank is not an option.
View 8 RepliesHaving a chance to try an O2 Sensor Simulator on your truck? I am wondering if they actualy work or if I should just stay away from them. Are there any problems or improvements using a SIM?
View 13 RepliesI have a 70 Ford f250 with a messed up wiring harness. Truck will run only in start position. which wires are wrong.
View 7 RepliesI bought a great 76' SuperCab with a 390 4 barrel Wednesday (the 30th) and while driving around the neighborhood this evening the truck just lost all power and came to a stop. No lights, no engine, nothing and I cruised to an easy stop (fortunately at the end of my own block). I thought I smelled a bit of electrical burn for a moment after I came to a stop but could not track it down before the smell disappeared.
Some early symptoms - on drive home from purchase, the turn signal light function was in and out. The starter was also turning slowly and sounded tired/weak. The ignition switch was a bit loose and previous owner said you had to make sure the key was not all the way to the right or accessories would not work.
Some early checks/fixes- replaced battery and battery cables and checked grounds. Starter began turning stronger and turn signal lights were back. Thought I had it going well.
My 2004 expedition wont go into any gear the shifter will not move I changed the stop light brake switch and a 30 amp buss fuse I found blown and also the check engine light is on now too this was after I parked it I also changed a 30 amp buss fuse I found blown out but it still don't work the only way I can get it into gear is to push the little button under steering wheel...
View 2 RepliesMy 85 f150 5L is parked to far in into my alley.. the last time i saw my keys i moved it up to water the plants that it was tucked almost on top of.
ive been looking for the keys for 2 months.. the truck isnt being driven at all but i think my neighbors are getting mad at it being out so far.
I can get in the engine bay, and i have jumped the starter on our big trucks at work before.. but what wires do i have to join to put the ignition into the run position?
I just bought a used F-350 that was being used by a fire department. They did something to the wiring to where most of the electronics won't work unless the key is in the "ON" position. When I open the doors, the dome light doesn't come on, nor does it come on with the IC dimmer switch, when I turn the key either backwards or to the "ACC" position the radio won't work, the headlights DO work but I don't get the warning chime when I open the door with them on.
The flash-to-pass works, as do the hazards and the turn signals (which seems odd -- I don't recall having a car where the turn signals worked without the car being on). With they key on, everything works including the dome light and the door chime. Is there some simple thing they could have done that would make it work this way and is easily reversed?
2002 Ford F250 V10 Auto... When I put the transmission into reverse, the starter kicks in...
View 8 RepliesI have a 1998 Ford F-150. It has an issue with starting sometimes. The truck won't start with a fully charged battery but when I hook it up to a charger, the truck starts normally. It was going to get the wheels aligned today and when the mechanic went to drive it off the ramp, it wouldn't start. I told him to put a charger on the battery and it started right up. Without the charger it just cranked over and wouldn't start. It doesn't do this every time I go to start it only occasionally. The mechanic had no idea what the problem was and has never heard of this kind of situation. I'm assuming it is an electrical problem but I'm not an expert with engines. The battery was fully charged at the shop and the battery is a year old.
View 4 Replies2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 RepliesI am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesI plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 Replies