Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 RepliesAny COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesLooking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesLooking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesI am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 RepliesI am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesI'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 RepliesWhere can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 RepliesI just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 RepliesMy park lamp circuit is dead. I have tested with a multi-meter and there IS power at the fuse. However, no power at the plug. I have pulled the bumper and found the plug for both the rear taillights (the park lamp circuit WORKS in the taillights) and the trailer wires. Confirmed it is dead there as well.
Both bundles go into the frame rail at the fuel tank, but I not sure which is which where it comes out at the firewall. A web search did not reveal a diagram and the Ford repair CD I have does not list Excursion diagrams.
Just bought a used, 03 F-150 SuperCrew Lariat. Having some minor electrical issues. While cleaning truck, I discovered a red wire coming into engine area on passenger side of vehicle. Wire has a built in 40amp fuse but isn't connected to anything. What this is for/ should be connected to???
View 1 RepliesMy 85 f150 5L is parked to far in into my alley.. the last time i saw my keys i moved it up to water the plants that it was tucked almost on top of.
ive been looking for the keys for 2 months.. the truck isnt being driven at all but i think my neighbors are getting mad at it being out so far.
I can get in the engine bay, and i have jumped the starter on our big trucks at work before.. but what wires do i have to join to put the ignition into the run position?
My 77 F150 Ranger with a 400 in it didn't wanna start up at all. It wouldn't even crank or click like if the battery was dead. Then I tried again this morning and it cranked once then melted a red wired with I think a black or gray tracer, on the ignition. (I put a new solenoid on a couple months back and the positive also melted a bit by the solenoid but didn't pay any attention to it.) I'm just wondering what could be wrong with it to make it do that and how to fix it. Also when I went to put gas in it (it's on a slight hill making it lean to the driver side) it was empty but no fuel would go down the filler neck, then it started to gurgle and spit it out some. I was told it was vapor lock but I thought vapor lock happens when it's hot.
View 3 RepliesLooking for a pic of the headlight plug wiring diagram?? I have the B5.5 lights, I don't know if that makes a difference. I need it for my latest retrofit.
View 1 RepliesI posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
I've searched all over and can't seem to find the answer. When I pull the tail light out of my 12 F150 there is a blue/wht wire and a black wire going to the back up light. I assume the blue wire is the positive and black is the ground. Is that correct?
View 8 RepliesThe red wire coming from my fire wall is not connected to anything and I need to find what it is supposed to connect too it come out of my firewall near my steering column ... This is and 95 f150 with a 302 engine ...
View 1 RepliesI'm planning the install of a 1996 351w into my '77 F-100. I'm using the '96 accessory serpentine drive (FS-10 A/C compressor, '96 alternator, etc.). It needs to mate up to the '77 wiring. I'm going to use stock '96 underhood A/C components (accumulator, hoses, condenser).
As best as I can tell, the '96 system uses the ECU to manage the A/C system, but I've converted the '96 motor to a carb.
Looking at both the '77 and '96 systems I think the easiest underhood wiring solution would be to use the '77 compressor ON wire as a relay trigger, and use the '96 High Pressure Cut Off (HCPO) on the compressor manifold, and compressor cycling switch attached to the accumulator to interrupt the relay output to the compressor.
I can get the switches and pigtails, and I can look up their pressure trigger points, but I don't know the voltage the '96 switches operate at (12v or some reduced voltage?) or how to simulate their trigger conditions to see how they work. I guess that at ambient pressure the HPCO should be normally on and the cycling switch should be normally off. So I could just wire them into the relay ground or trigger connection. But of course they aren't simple two wire switches. (Edit: Looking at it online, the cycling switch appears to be two wire, the HCPO is 4 wire).
How to wire them, should I use them to interrupt the relay ground or trigger connection?
On a 2008 E250, Where is the dome light wire and what color is it? To use with an omega security system.
View 4 RepliesI have a trans temp gauge on my 1996 F350, I have it all hooked up and functioning except for the light. I have searched without success looking for where to splice in to get the light on and have it dimmable. I have a wire routed from the gauge to the center of the dash behind the stereo. What wire I can splice into?
View 2 Replies