Clutch is starting to slip - can't handle torque above 3k in 6th gear.
6500 miles on the car
700 miles with module
Never launched - just wind out gears occasionally
Don't have to ride clutch on hills
Not a daily driver - not stuck in traffic
I shift like a granny...
So I have a stage 2 endurance clutch and light weight flywheel on my car. I had not really gotten on it of late until yesterday. I was getting on the highway and really got on it. When I hit third gear it felt like my clutch was slipping. I have only had it on the car for like six months and about 10,000 miles. It could be worn out all ready? And after the incident yesterday I pushed the clutch in and held it to let it cool down a bit after it did it held fine even in higher Rpms didn't feel like any kind of slipping. Pulled very strong. This morning after having all night to cool off (and I mite just still be freaked out a bit) but it seemed to feel different, like a possible slip at 3,000 Rpms but again I mite just be freaking out about nothing. What does a master cylinder or slave cylinder going out feel like?
View 1 RepliesSo I got my stage one flash yesterday and I noticed 5th gear slipping already. I don't plan on getting a k04 upgrade, maybe stage 2 down the road. so I am looking into the drop in clutches, preferably this one [URL] .... I am just trying to find out some reviews from people who are currently running drop in clutches and the issues that they have come across.
View 8 RepliesSo I was driving my car and notice when I was in 5th gear the rpm was at 3 and was increasing to 4 then when back to 3 or 3500 rpm. I tired it again but with a little more gas to it and got the same results. Wondering if this is signs of clutch slipping or another cause.
View 5 RepliesI have a 2012 Golf R 6 Speed manual, Just noticed that my clutch was Slipping in fifth gear when I give it gas. What clutch kit is recommended. It is the first time I have a VW and dont really know what will work better on it. Mods are Full catless downpipe and exhaust, Injen air intake and Revo stage 2 tune, ST Coilovers and NICHE Bronze wheels. Podi boost gauge and AEM wideband. I put down 285hp and 310TQ at Dyno jet 2 weeks ago I was kind of suprise expected a bit more but maybe the clutch was going bad already.
View 1 RepliesMy first VW was '99 Jetta that had 150xxx miles on the original clutch before it was stolen in '11. I leased a GTI shortly after, and decided to buy it out last year. At 35,000 miles I am starting to get I guess what I would describe as a chatter when slipping the clutch into first and sometimes second. Car is stock, never abused. I tried to reproduce this for a video clip but the problem is sporadic. Never had a clutch go on me so I don't know what to expect, but from what I've seen of people losing their stock clutches after ecu flashes is the car slipping under wot in top gear. I don't have that issue. No other symptoms. No stubborn shifts or anything, clutch still feels the same and rpm's have never flared up on shifts.
View 5 RepliesHaving clutch issues? I have just put 10k miles on my JSW and the clutch feels like it slipping in 1st gear when heavier load(uphill ETC) is present its even worse. We have never drove it hard pretty much cream puff.
View 9 RepliesI've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
I have a 06 plate Santa Fe 2.2 diesel and i think the cluch is on its way out, keeps slipping out of gear and the pedal itself is not aligned with the other two, mileage is about 79K i think.
View 4 RepliesI have a 1994 Geo Metro that I picked up a little over a year ago. I had to swap engines and replaced the clutch at the same time. This included a turned flywheel and new pressure plate. I also replaced all seals and gaskets except for the distributor O-ring and the head gasket. This included the crank and cam seals on the front and rear of the engine as well as the seal housing gaskets/oil pump gasket. I drove it for several months and then the distributor O-ring began to leak oil profusely which is a common problem with these cars. The distributor is keyed directly into the camshaft on the rear side of the engine so it sits sideways directly above the transmission/engine interface. Some of the leaking oil went right down into the clutch area. Being that adding a cup of synthetic oil every day was still cheaper than driving one of my pickups, I just kept driving the car until the new O-ring arrived and added oil. Once the O-ring was replaced, the oil leak stopped.
I had a couple episodes of clutch slipping not long after the leak was fixed and then everything seemed fine. I figured that some oil got down there and wore off after the clutch stopped slipping. The car drove fine for about a year until I began noticing the clutch slipping under load in 4th and 5th gear. I had some suspicions of this for a week or so before it became more obvious that the clutch was most definitely slipping. I have a new clutch kit and a spare flywheel that I plan to have machined in the next few days. I have been driving it a couple weeks around town and just babying it so the clutch won't slip.
I was also told by some that I should intentionally burn the clutch some to remove any glaze build up on the clutch disc or flywheel/pressure plate surfaces. They told me to put the parking brake on or put the front bumper up against a tree and burn the clutch. I originally figured this was a bad idea but decided to try it yesterday, figuring I had little to lose. I did it just until I began to see smoke and smell it and then stopped. I let everything cool off for an hour and then took the car for a drive. The clutch was no longer slipping at all so I am wondering if this fixed the problem for now or simply delayed the issue for a short while. I am sure I took some life off the clutch by doing this but....
I have a 2012 GTi. I just got the stage 2 unitronic flash on my car and now my clutch slips bad. I know i will need to replace my clutch. It was starting to slip before the tune and now it just cant handle it. The shop I went to recommended a South Bend Stage 2 Clutch kit (single mass). Its a daily driver and want something that will last and hold up to 325ftlbs of torque. I do think i want to go with the single mass clutch though.
View 13 RepliesI am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.
Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.
My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.
1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.
I have a 1997 F250 heavy duty 4x4 7.5 efi. I just bought a 2003 weekend worrior weighing 5800lbs dry. When I go up slight hills in 4th gear it seems to work real hard especially on freeways, could my clutch be slipping or am I just at max tow
View 11 RepliesI just had a new clutch installed yesterday. Bully stg3 with flywheel. My 2012 R has 22k. I had to change it since my stock clutch was slipping at 3000rpm with the Unitronic stg1+.
The second I start the car and stay on neutral, give a little gas I hear a super loud grinding noise. It stop when I press the clutch. On idle I don`t hear nothing and when I drive everything is fine until I release the clutch and when I don`t press the gas.
The shop said they never heard anything that loud and they confirm that everything was installed correctly. Other then the noise the clutch is fine and works very well.
So i have a 05 1.8t gti... just bought it about 3 months ago and it has a stage 2 south bend clutch... the car has only 68k on it and the clutch is slipping already... it was driving fine then about a week ago all hell broke loose and it's slipping bad... now for my question what performance clutch is recommended? I have a giac tune and its pushing about 21 boost... . would a 2.0 performance clutch work on the 1.8t?..
View 12 RepliesWell the clutch started slipping finally, not sure if it was the weather change on the drive from here to PA but I slip 5 and 6th wot 4-5k rpms. Have some coin set away because I knew it was going to happen sooner or later did some searching and I'm curious to here the verdict on the RSR clutch how many miles and how its holding up as well as whatever else you are running. Will probably keep the car 2+ for quite a while so not really worried about 3+ power.
View 24 RepliesMy wife was driving my Stage 1 R last night (by herself) and she ran into an issue where when she tried to leave from a red light, the clutch was slipping through the first three gears and she could barely get up any speed. She pulled over, let the car sit for a few minutes and then started going again with no issues.
She drove home about 5 miles and told me about what happened. The car smelled like burning clutch, but when I took it out for a quick test drive, everything seemed fine.
I am at around 5000 miles and have never had any issues before and I don't ever do high-rpm launches. So, could this have been a fluke or a sign of the clutch/pressure plate issues people have been having?
Well I was hoping it was just a fluke the one time it slipped about a month ago, but my clutch is now officially toast. If I'm between 3-4k RPM and punch it in just about any gear I'm getting slip. Trying to pass a car on the highway, and I'm getting slip. I do not launch my car, I simply like to play in the 3-4k rpm powerband as I love the torque. Apparently spirited driving while remaining in the peak torque range of the engine will kill the stock clutch. God only knows how long the OEM clutches will last with people that drive their R like a racekar... 3200 Miles, Stage 1+ ....
View 24 RepliesI have an issue that I thought was a slipping clutch, but my dealer says it isn't. If I'm cruising at highway speed (stg1 gti)say around 65 and I get on to pass the revs will surge, but there will be no apparent acceleration to go with it. The dealer said it isn't the clutch because there is a standard test they do where it would be jerky in 2nd. Could this be a DV or something?
View 24 RepliesI went stg.1 at 1000 miles & stg.2 around 6000
miles, then K04 I'm at a little over 6400 miles & my clutch slips in 4th & 5th gear. I never got the chance to install my APR inner cooler. I really hope the Southbend stg.2 endurance setup works well so I can move on to the suspension. This hobby can get expensive but the car is a blast to drive! It never fails to put a smile on my face & has definitely taken the smile off other drivers faces when they realize they can't get by me.
So my clutch started to slip in 4th when I first got my apr stage 1 tune at 24k miles. now 600 miles later it's slipping in 3rd. put it back to stock mode and it doesn't slip in any gear.
My question, if I replace my clutch with an OEM sachs what are the chances of it slipping again? From what I understand the golf R uses the same clutch disk and pressure plate as the gti so why is mine slipping so early? luck of the draw?
I prefer oem because it is a lot quieter and I do not plan to mod any further than stage 1. I'm still running the stock airbox.