Golf IV / Jetta IV :: 2000 - Key Fobs Not Working?
Apr 21, 2016
I replaced the batteries in my key fob yesterday, and now it doesn't work. My car has no accessible exterior key holes, due to the trunk lock being seized as long as I've owned it, as well as the drivers door lock having the exterior plastic cap(is there a lock still hiding under there?) So instead, I hopped in through the sunroof since I had left it open, and once I opened the door the alarm went off. I disconnected the battery, and when I reconnect it, the immobiliser resets. I assume that my fobs have reset, so with there being no exterior locks and no fobs programmed, what should I do? The car is not driveable at all right now, and I can't even close the sunroof in case it rains.
Some additional details:
2000 Golf 2.0 VIN WVWBA21J0YW745218
Fobs are HLO 1JO 959 753 F
View 4 Replies
Advertisement
A few months ago I'm key fobs stopes working the I switched out the batteries and still no progress. What it could be?
View 3 Replies
My blower motor in my Jetta recently stopped working. When I turn on the blower it works for 10 seconds or so then slows down and dies. Is this a blower motor or resistor problem?
View 1 Replies
I have changed the batteries in the remote for my MY 2000 Jetta MKIV VR6. Now the remote is not working. A search suggests I need to program the remote using a specific procedure. Alas, I have found various procedures, and so far none has worked.
First of all, I have two keys, Both were functional. One still is.
What I tried:
-Put key with fob in ignition and turn key to accessory mode position.
-Wait 5 seconds
-Hold lock button on 5 down for 10 seconds.
-Turn ignition off and remove key.
-Close doors on car and trey to lock/unlock - not working!
I'm sure I can find a few more suggested methods, but what's the proper method?
View 24 Replies
I've got a UK 2003 Phaeton (78Kmiles). Picked it up 6 months ago and have put 8K miles on it with no issues at all until...
The key fobs just stopped working. Car was supplied with two fobs and both stopped working. Replaced the batteries to no avail. Press any of the buttons = light on the key works but the car ignores it totally. (even right next to it)
I can use the key for entry / lock /,alarming, but it's really not cricket for such a fine automocar.
View 12 Replies
My Mom used my Ex to take the kids to the park today. When I went to unlock it with the fob.... NOTHING! I thought maybe a bad battery, but when I got home and tried the other one it didn't work either. Is there a fuse or something that would have gone bad? Everything else in the truck is working fine except for the remotes.
View 13 Replies
I have a problem with my 2007 Prius. The low beam and both FOBS for the car quit working at the same time. It worked the previous day as always, then the next morning, the car would not automatically unlock and had to use the FOB mechanical key for entry. Then I noticed that the headlights (LOW)would not turn on, but the high beams worked fine. Just an FYI I have changed the headlights on this car at least 3 times in the past 4 years.
View 7 Replies
Tonight the wife when she got home set the car's alarm off and after she turned it off none of our remote starter fobs will function (lock, unlock, alarm..)
The factory fobs still work fine.
Am I stuck going back to Hyundai to get the remote starter fobs fixed ?
View 7 Replies
New batts in remotes (remotes do nothing but do start the car when inserted in dash).
12 volt batt removed and tested good at autozone.
Tried the "key" button under steering wheel in both positions still not working..
Checked all fuses under the hood, all OK ...all other items in the car seem to work..
None of the exterior black buttons work..
View 17 Replies
Heat blows warm at best and A/C isn't all that cold. I want to believe its a blend door issue and dive into it this weekend and fix it but there isn't a single piece of foam coming out of any of the vents. Of all the systems on the car HVAC isn't my cup of tea I don't know anything about it. What else could be the problem?I can live without A/C but the heat things must be fixed.
View 1 Replies
Today I pulled off the front bumper assembly to install an oil pressure gauge. The wire that goes from the sender to the gauge I pulled through A rubber boot that had a cluster of wires located next to the driver side windshield wiper, I pulled the wire through with a coathanger or I could've scratched another wire which is causing the gas pedal not to work? Or could it be when I pulled off the bumper assembly something unplugged or broke? VW GTI VR6.......
View 1 Replies
After a long day at disney, we walked to the car, and couldn't remember where we parked. I kept pushing the panic button looking for the car (I read pressing buttons too many times out of range can cause it to un-sync from the car, might not be true though?). Well now my keyfob won't do anything except start the car. I normally wouldn't care at all but I can't lock my driver door.
For some reason my key won't turn right to lock the door, and will only turn left to unlock (not sure if that's just how it's supposed to be). I tried something that I was pointed to in a thread on here [URL].... but could not get it to work. I don't have 2 keyfobs, just one and a valet key. I put a brand in battery in the key hoping that would work, but still nothing. I don't live in the best area and I'm desperately trying to find a way to lock my door without having to go to a dealership and shell out a bunch of money.
View 5 Replies
About a week ago I turned on the Climatronic a/c in my 99.5 GTI for the first time since I bought the car. Everything worked fine until a bug splattered my windshield. I sprayed washer fluid and the wiper moved extremely slowly to the halfway point and then stopped. The wipers have always moved slowly since I got it about 6 or 7k km ago but have never become stuck. I turned off the a/c and let the car sit for a while turned off. When I turned it on again, the wipers worked fine but the were noticeably slower then before.
Cut to a few days later, I turn on the wipers to test it out and it gets stuck again, this time about 3 inches from the bottom. I can hear them clicking as if they are restarting the cycle, but it only twitches.
Cut to now, the wipers try to move every time I turn the key to ACC, as well as twitching when the car starts. When I start driving, after approx. 2 minutes my ABS light comes on and doesn't go away until I shut off the car.
I have provided a video. This is my only car and there's rain coming up in the forecast ...
View 6 Replies
I have an 01gti glx and my headlights are not working when i turn my headlight switch on. They work just fine when i release the ebrake just not working with the switch! I checked the fuses under the dash and all were good.
View 3 Replies
A couple months ago my Key Fob stopped working. I tried using the button and then tried to use the key to unlock the door. I'm trying to figure out if there is a possibility that the immobilizer in my fob is junk or maybe its something as easy as changing the battery (which is another issue in itself because I cant open the fob for the life of me) Once again just curious if there is something I can do to fix this issue without contacting and dealing with the dealership. Would like to be able to lock my car again at some point.
View 3 Replies
My, auxilary cooling fan isn't working. However, the bigger (primary) fan is working fine. Fuses, looks ok and i see clutch is engaging fine too. well, the a/c is working but not as it used to before. Its cold but very faintly. I suppose this could be because of the not working auxiliary fan.
View 15 Replies
I recently picked up an 02 Golf with a 2.0/5-speed. It's just a plain-jane model without all the bells and whistles. My fans and A/C aren't working. I can deal with no A/C but the cooling fans are kinda important. I did all of the trouble shooting. Both fans work on low and high when jumped at the radiator temp switch so my fans aren't the problem. I replaced the temp switch with no change. My OBD-II scanner shows that my actual coolant temperature was about 10 degrees off from my temp gauge so I replaced the temp sensor too. The timing belt and water pump were both changed about 5K ago.
I borrowed a "good" FCM from a buddy's car and that didn't work either. I went through the troubleshooting diagnostics for the FCM harness and see that I do not have continuity between T14/14 & T14/5 on the harness side. This indicates that the "F38 Ambient Temp Swicth" is possibly my culprit. Everything else checks out good on the FCM harness. Where is this switch located? I've searched online and found nothing specific to my 02. For the sake of testing can I jump these 2 wires for continuity to simulate a working switch? From what I've read this ambient temp switch disables the fans and A/C when air temps are below a certain temp. My next step is going to be wiring in a variable speed fan controller if I can't figure this out .....but I'd rather not get in to that if I can get the factory setup working.
View 1 Replies
Well my alarm is not working properly, when lock my doors all my doors lock but yet my headlights don't flash and i dont get any alarm chirp..
View 2 Replies
I am trying to figure out why my AC is not working. Both fans are coming on and the AC button is light up but it is not blowing cold. The charge was checked and it has a good charge. The compressor appears to not be engaging. I checked for power at the electrical connector for the AC compressor and my voltmeter is showing voltage between 3.1-8.3 volts. It jumps around between that voltage every few seconds. The fuses have all been checked and are in not broken. What else should I be checking?
View 2 Replies
I removed the rear shelf to do some reupholstering. Obviously, the third brake light is enclosed in this assy. Now every thing is back together and my 3rd brake light isn't working anymore. Probably got banged around when it was out. On troubleshooting it, it actually works but comes on so low that you can't even see it behind the glass. I even disassembled the whole thing and directly wired it to the car battery same results. All LEDs illuminate but at a fraction of what they should. I'd say maybe 1/10 of what they should. I checked continuity of the whole circuit board and every thing checks with no broken solder except for 1 diode. It's the black one on the far right that has no continuity. Why such a low illumination?
View 2 Replies
So I have been having issues with a cluster in a car I recently bought. Sometimes it works fine, sometimes no gauges or MFA, sometimes just no gauges. All of the dummy lights work, and the odometer has power, although it does not seem to record miles when the cluster is not working.
I checked for power, good. Looked in the Bentley for grounds, there are 3. Terminal 9&24 and a sender ground, terminal 7. 9&24 both show continuity, but I get zilch on the sender ground. Tried looking in the wiring diagrams and google but I cant figure out what a sender ground is or if it should have continuity?
Next step is to try another cluster, but I don't want to go through the trouble of switching it to a new cluster if the ground is bad.
View 4 Replies
