Golf IV / Jetta IV :: 2001 1.8t Stopped Running - Check Engine Light Blinking Because Of Misfire
Feb 27, 2015
So last Thursday I started my car up in the blistering cold and it ran fine for about a minute and started to misfire so I shut it off. It hasn't ran since. When that happened the check engine light was blinking because of the misfire. I didn't have a code reader at the time to read it. now that I got a code reader the damn thing isn't throwing any codes. it spits and sputters sometimes. I've had no previous problems with the car. Thinking It might be a weak fuel pump or bad coils and in not sure how to test them.
View 1 Replies
Advertisement
On my way to work, my check engine light started blinking and car was sputtering (real bad on idle). I ran the code and it came back with misfires codes. I changed the coils/plugs, fuel filter and fuel pump last year. Can the coils be bad already? When I clear the codes the car will run fine for a little while. But after a couple miles CEL will blink and the car will run roughly again.
Car : 2004 Golf 2.0
Codes:
16684: random multiple misfires
16648: fuel injector #2 short to ground
View 5 Replies
I have a 2001 Ford Windstar Sports SE with 155K miles. I did a tune-up eight months ago. With the tune up I had to replace the fuel pump because it was defective. Later, I found that there were misfires occurring since I was getting slow acceleration. I had the spark plugs on the guilty cylinders replaced again and the spark plug wires.
Periodically, I have had to return to the shop to have the vehicle checked. I sometimes get a blinking check engine light while trying to accelerate, which now occurs only while it is raining or I am exiting the car wash. The shop is at a loss as to what it is (spark plugs and wires are fine, no lose connections noticed). I am wondering if I should take it to someone else. Of course, taking it somewhere else will cost me $100 to check on someone's else work.
The shop replaced the ignition coil. Distributor cap is fine. They keep saying that the engine is running fine while in the shop and do not get any codes. I had them drive it while it was raining and they discovered that cylinder 4 is misfiring. They worked on the cylinder. The vehicle runs well, until it rains or I wash it.
My questions to the group, "If everything is OK, how come it is misfiring? What are they missing? What is the connection to the moisture?"
View 14 Replies
Our R32 has 2428 miles- and today the check engine light came on and it started to run pretty rough, babied it home and the the light was blinking when I turned into the driveway.. I know that booklet 3.2 in the owners manual is diagnosing catalytic converter issues...I have always used super unleaded, it hasn't even reached the halfway point of the first service.
View 10 Replies
2004 VW jetta 2.0 ... So my vehicle stalled on me i replaced the battery, the alt, and then when i started it after installing the new alternator it didn't sound right so i checked it out and saw a spark plug wire was in very bad condition and was causing a spark where the spark plug and the spark plug wire connect so i bought a new set of spark plug wires and swapped the old ones for the new ones. Now when i start my vehicle the check engine light is blinking and the car definitely does not sound right. i am positive i did everything correct when swapping the spark plug wires but i am lost as to what could be the issue.
View 1 Replies
I just bought a 2000 GTI with the 1.8 turbo. It was very affordable, but it had a few problems. On hard rides, the check engine light was blinking AND I think there was too much oil in the crankcase (I say "think" because the dipstick funnel is gone and I'm not sure how far down the dipstick should go -- new one is on order).
I got rid of the extra oil, and now if I keep the oil in the hatched area of the dipstick (with the dipstick pushed down as far as it goes), the check engine light will never blink even under hard driving. But with the oil that low, the oil light will flash and beep on hard turns. I was experimenting, adding a little oil at a time, and hoping to find the magical sweet spot where neither the check engine light nor the oil light would go off. Instead, tonight I found the opposite -- the sour spot where BOTH of them go off.
So now I'm thinking maybe I need to change to a thicker oil. This car has 124,000 miles on it and was recently refilled with 0w-40. On my last car (a 1994 Golf with the 2.0 liter and 140,000 miles), the oil light would beep on hot days. I solved that permanently by changing from 0w-40 to Mobil 1 15w-50.
Finally, I checked the codes and it said there was a misfire in #2 cylinder as well as general misfiring So I checked the plugs and discovered that the previous idiot had gapped the #2 plug at 1/8 inch! So I (the present idiot) regapped them all and the engine seems to run better, but maybe going for months with such a huge gap has already fried the #2 coil. Should I just replace it? (or all of them?)
View 14 Replies
Ok...so I drove my car last night about 120 miles and all was well. Got up this morning to go run some errands and the car started acting weird, sputtering. The check engine light was blinking on and off, then it came on solid and stayed on. I haven't checked the code yet.
2004 Jetta GLI1.8 T Manual Transmission
View 7 Replies
My 2002 Jetta GLS 2.0 is misfiring only when it rains out. I go to start the car and the car idles extremely rough and seems like it wants to die. I checked out the codes for the check engine light and I got misfire codes p0304 and p0300. Which is a general misfire detected, and misfire on cylinder 4. I noticed that when I misted the alternator during the day around 70 degrees with the car running the car would misfire and almost die out. I know you are not supposed to get the alternator wet, but keep in mind i did not soak it I misted water on it. I misted the coil pack and nothing happened. I replaced the spark plugs and wires a few days ago. But as soon as it rains my car does not idle right and the check engine light flashes.
View 4 Replies
I have a 1996 chevy caprice wit a 4.3 v-8 one day i was driving and the car started acting funny and the check engine lite started blinking i had the codes read and 0p300 came up saying multiple misfire so I changed the plug wires they all connect in the front around the harmonic balancer well that didn't work its still saying multi misfire so I took a spark plug wire off of the electric dis block and no change in motor now I don't know what to do...
View 5 Replies
Just bought 2007 Gs 350 in Dec 2015 with 60k miles. The other day I filled up with gas and drove to work. On the way home check engine light started blinking, check VSC appeared on display screen and traction light came on, car ran rough, and wouldn't accelerate. Got home and searched the net.. So I removed gas cap... No change.. Then removed neg battery cable for 10 min. Fixed problem for about 10 min. Then it all happened again. Next morning took it to Lexus dealer. The rep called and said it gave misfire cylinder 3. They said they checked valve springs and they are good, exchanged coil pack with different cylinder and still misfire #3. He said has to be injector so they want to replace injector ....
View 8 Replies
I have a 96 Grand Voyager that had had sat for a year undriven or started due to being out of state. It ran like a champ when I parked it. Now I charged the battery and went for a drive on the freeway and my check engine light came on and started blinking. I had the code read it came back with 2 codes a P0306 and a P0300. I noticed that the cylinder 6 spark plug wire was arcing on the core support. So I replaced all the plug wires and spark plugs with Champion platinum spark plugs. I cleared the codes and took it on a test drive and the P0300 code came back. Is there anyway the old gas is causing the random misfire? or what else could it be?
View 1 Replies
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
View 1 Replies
So my gf's check engine light on her 01 Golf flashes once in a while, and it misfires. But the thing is, it doesn't stay on, and it's once in a while (like once or twice a week). She has new spark plugs, and new wires. I have a feeling it's the coil pack, but I really don't know if it needs to be replaced until the check engine light actually stays on.
View 14 Replies
Just a few days ago I was driving and I noticed as I went over 35 mph my car would stutter and the check engine light would start flashing. And when I slowed back down the car drove fine. I'm wondering what the problem could be? Feels like the car is losing power. Car is currently at 119k miles.
View 1 Replies
It's a 2010 vw jetta. Check engine light is blinking and the epc light is on the car is not paid off yet have no.
View 19 Replies
I have a 2006 f250 5.4 4wd with 5r110w trans. Check engine light was blinking and then one day the tranny just stopped working in all gears. Engine code p0751 came up, shift solenoid "A". Changed it, code went away and still no gears. Checked pump pressure, good in all gears, all I can think of now is TCM....
View 3 Replies
My Girlfriend just got a 2003 Hyundai Elantra and everything was running great on it the first month she had it BUT the check engine light was on.. After about a month she called me up while driving and said that the check engine light was blinking and the car would hardly move. So I got to the car and looked at it and I noticed the oil filter was a little loose so I tightened it good this time and added a little bit of oil. It actually moved but it would hesitate. So we had it towed to a shop and they read the codes from the check engine light and told us it was leaking oil from the motor some where (not specific) and it also needed a new O2 sensor.
So I replaced the catalytic converter underneath the car and also a new sensor along with a new set of spark plugs. It ran alot better and I left it at that. Now about a week later she was coming home and noticed that when she turned left or right that the battery light and brake light on the dash came on. She drove it home and when she turned in the driveway the car went dead. It started right back up and we got it to the house and left it over night. I went out this morning and again it started right up. but when I lifted the hood I noticed the belts on the pulleys were all spinning very slowly. I'm not sure if it could be a timing chain or if it just needs new pulleys.
View 6 Replies
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 Replies
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 Replies
I have a 2000 VW Jetta 2.0l AEG engine with 190,000 miles and check engine code P0303 for the 2nd time in 3 months. I had this same code 3 months and 3000 miles ago and found the spark plug #3 to be fouled up. All other plugs and wires seemed to be okay so I replaced plug #3 and the problem went away. I suppose after I take off the upper intake manifold I am going to find the same plug #3 to be fouled up again. The engine is a typical AEG that I have to add 1 quart of oil every 1000 miles as it has been burning the same amount of oil since I acquired the car at 135,000 miles. I have read that the wrong piston rings were installed from the factory on a large number of these engines and VW says that if less than 1 quart of oil is burned after 7500 miles it is normal. I really don't feel like spending 2 hours every 3000 miles to replace plug #3 ? It might be time to part ways with my 2nd VW. As a side note, this car has been averaging 35.5 mpg over the last 55,000 miles that includes 50% city/ 50% highway driving. I coast to red lights and don't accelerate quickly with the 5 speed manual transmission to achieve hybrid like fuel efficiency.
View 1 Replies
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies
