I have a 2003 vw golf gti. and It will crank but it wont start. I recently replaced the fuel pump and the relay.
There is no voltage at fuse 28 so I jumped the relay ( using both big pins ) and still no voltage at the fuse. however when its jumped the fuel pump actually runs. Still nothing
I am beginning to think it may be a spark issue but the fuel pump doesn't make a noise unless the relay is jumped.
My Daughters jetta will at time no start after it has been locked then unlocked. She told me that if the car doesn't beep when locked she sometimes has the problem.
The dash will light but no crank at all. Could this be an alarm issue or something else? I
04 Gli 1.8t 6 speed. When I go to start my car and turn the key nothing happens . No clicking no cranking nothing. All my lights work radio works everything. Would a bad starter cause this? I can jump my car and it works fine.
View 7 RepliesI am having trouble with my car not starting, when turning the key nothing happens. I have replaced the battery and have even tried to push the car and do a rolling start could not get it going. I am assuming that if i can't do a rolling start that rules out the starter, is that correct? I also verified all fuses and changed the fuel pump relay.
I am leaning towards an electrical problem (ground/short circuit). I have a Bentley manual and VCDS tool, how to diagnose the electrical problem and pinpoint the issue.
So I have a no crank no start. All other electrics appear to be working . For the most part I just hear a soft click when I try and start. Doesn't sound like your normal solenoid clicking. New starter, 12v at battery , new ignition switch. It did this to me last month , started taking the ignition out then just only started before I could even get the new part in.
Changed it anyway. Seem to fix it. My next step is going to be to check the ground under the battery. Which I checked and cleaned up a little bit about eight months ago. After that I'll try and jump the starter and check the voltage going to the solenoid. I check the fuses last month when it did it to me and they all seem to be okay.
So i had my starter crap out on me the other day, it destroyed its self in good fashion. So i replaced it thinking that was going to be the only problem, but once i replaced the starter it STILL wouldn't start. the starter spins, but doesn't engage the flywheel. I can start the car with a bump start no problem...
Things I have done:
- Replaced the battery - 660CCA AcDelco
- Replaced the Ground wires, and positive, with new 1 gauge wire, and cleaned the connections.
- Replaced the starter A new one from acdelco, and a Used one (that was in working order)
Getting 13-13.5 volts while running.
Signal wire is fine, as I've tested the starter by completely bypassing it and just jumping straight from the Batter, still the same situation.
My only thought has been.. is it feasible that the starter may have destroyed a couple of teeth on the flywheel.... so when i goto engage the starter it might go for a quarter revolution and then find the location with the missing teeth and just spin ?
So i got a 2002 gti 1.8t awp . Wont start unless I crank it about 2-4 times. Also noticed a bit of a grinding/high pitched noise when cranking. when the car starts up it idles perfect, doesn't die , drives perfect etc...
Eventually i got the car scanned. & got 2 codes.
P0341 : Camshaft Position Sensor A Circuit Range/ Performance B1
&
P0230 : Fuel Pump Primary Circuit Malfunction
So I went and bought a Fuel pump , Camshaft position sensor & Even a new starter. Nothing fixed it. & the problem still occurs..
Heres a video of me trying to crank it ; [URL] .....
Driving home on the highway today, not boosting, just regular driving. Car was acting fine, then just shut off. Tried starting, and it would crank, but not actually start.
Got it towed home. Scanned. Two codes: 01314, Engine Control Module. And again, 01314, Engine Control Module. Tried clearing codes, and it says "comm. error". Im using the VAG Check scanner from ECStuning, has always worked fine.
Thought it could be fuel pump, but the fuel pump primes when I open the door. I did notice that the throttle body refuses to align when I put the key in the second position, when it always has before. Radio works, all presets work. Unplugged the battery for a half hour, replugged, nothing. I'm leaving it unplugged overnight to see if that does anything.
2002 Jetta GLS 1.8T (engine stock except diverter valve) 171k miles
It's done this a couple times now. Both while raining out/high humidity. Prior to this, I could hear the pump "growling". Sounded like maybe starting to go. You could hear it prime when opening the door or turning the key forward but would stay sounding like that even when the car was started. Without the radio, you can hear the pump running.
1st time- The car will crank without issue but never start. I let it sit a few minutes, turned key, heard it prime,tried again, started right up like there wasn't an issue and I couldn't hear the pump this time while the car was running.
2nd time-The car will crank without issue but never start. I let it sit for an hour, opened door (couldn't hear prime), checked fuse 28 (good). Figured wth, let's try anyways. Turned key, couldn't hear prime, started right up. WTF. cold idle normal (1000-1200rpm), light revs to 3000 ish normal. Turned off car, let sit for a minute. Turned key, heard prime, car started without issue and I couldn't hear the pump again while the car was running.
My dad is thinking to replace the pump right away. Is there anything else to try? The relay is working... at least sorta. With the somewhat intermittent issue, where to start? Either way, relay or pump, I will be replacing fuel filter.
1999 Jetta 2.0L manual trans
One day out of the blue the car would not crank or start. Checked and found that fuse #14 was blown and would blow the instant another fuse was inserted. Checked all the typical locations for wiring issues usually associated with the comfort module because it had all the symptoms of a faulty module (the power windows did not work and the fuel pump didn't pressurize the system when the driver door was opened, the alarm didn't set, automatic door locks also inoperable).
I checked the dome light, trunk hinges, rubber boot between doors and body and found nothing. Put a jumper wire into the neutral start relay and was able to crank the car. I then replaced clutch safety switch, neutral start relay and installed new (junkyard) comfort module and the car cranked up, started and everything was working normally again...for about 3 weeks. Then it did the exact same thing again. Fuse #14 was blown again and would blow the new fuse as soon as it touched the terminals in the fuse box.
I reinstalled the jumper wire in the start relay in order to be able to drive the car for the last week, and then last night out of the blue the car would crank, but not start. I turned the engine over several times and could hear the fuel pump pumping and even smell fuel, but no start. 3-5 minutes later after random tries to start, the car stumbles to life as if it wasn't getting fuel, and then drove 10 miles home with no issues. I returned the 'faulty' comfort module Monday and got another one but haven't installed it yet because I fear the same thing happening with this one as the other one.
Last night after I got the car home, I plugged in the comfort module and everything worked like it was supposed to. Can a faulty fuel pump damage the control module? I'm trying to get to the bottom of this and fix the problem and not the symptoms so I'm looking into anything that could potentially cause the problem.
I have a 2002 2.0L 5spd Jetta that has an intermittent crank no start issue. The car has about 140k miles on it. The car will crank, but will not always start. It seems to start about 8/10 times. During the cranking, there is a rough noise coming from the starter area. More on this noise later.
When the car starts, no codes are thrown. When it refuses to start, the following codes show up:
P0261 Cylinder I Injector Circuit Low
P0267 Cylinder 2 Injector Circuit Low
P0270 Cylinder 3 Injector Circuit Low
P0264 Cylinder 4 Injector Circuit Low
P0445 Evaporative Emission Control System Purge Control Valve Circuit Shorted
P0037 HO2S Heater Control Circuit Low B1S2
P0418 Secondary Air Injection System Relay "A" Circuit Malfunction
P0420 Catalyst System Efficiency Below Threshold (I don't think this is related to the intermittent starting issues)
I've read up on these codes, and there are instances of other people getting these codes as well, but unfortunately, I haven't found any "smoking gun" that's the root cause to solve the issue. What I've tried, chronological order; none of these solved the problem:
Checking for spark. The spark plugs are new (within 2 months), but I removed spark plug and checked for spark.
Check fuel system: I removed the fuel line to the engine and drained it to a jug. I saw fuel flow intermittently when I keyed on the car. (Should it flow continuously?)Replaced the fuel filterSwapped fuel relay 409Checked wires near relays for obvious signs of damage (admittedly maybe I missed something here)Swapped coil pack. The coil pack was replaced in April, but I put a different one on, to no avail.
The spark plug wires were replaced at the same time as the coil pack.Starter
Thought fixing the noise might fix the starting issue. The noise from the starter is a grinding noise that occurs during the cranking process (not after, as is a common problem with these Jettas. It's NOT this noise: [URL] .... In any case, I tried the fix for the above noise by removing the starter and regreasing the inside. That didn't work and the noise and the intermittent starting issues are still here.Finally took the starter to Advance Auto Parts, had it tested, and was told it was good.
I think I have two issues that may or may not be related- the intermittent starting issues and the noise issue. They started happening at close to the same time.
Okay so my 2003 Jetta GLI normally starts without a problem. But it seems like whenever it gets cold (below about 40) it doesn't even try to start. I turn the key and nothing happens, the engine doesn't crank. All the lights turn on like normal and they're not dim so I don't think it's the battery. It'll still start if I roll-start it, but there isn't any sort of hill for a few miles. Normally once it warms up later in the day it'll start up.
View 3 RepliesI bought an 05 golf GL with a 2.0 and 5 speed in January for commuting to work.
Well, recently. I was on my way home from work, I'm an engine tech for Cummins Inc, and I notice my CEL came on and the car stalled multiple times at red lights. So I limped it home, connected my scanner and the fault was "Implausible signal from Mass Air Flow sensor". I cleared the fault code and tried to start the car. Nothing, no crank no start. Just an audible click from under the hood.
I disconnected the battery for 5 min reconnected it and it started fine. Drove it to work the next day, no issues. I tried to start it again and nothing, CEL was on again for the MAF sensor. I pop started it, car ran like hell, rough idle, low power, etc. luckily I have a dualy that I can drive in the mean time.
After installing a new crank position sensor on my 05 GTI 1.8T would I have to recalibrate my ECM, my car will not start.
View 2 RepliesMy car is a 2003 Jetta GLS 1.8t. It has 223000 miles, yet other than normal maintenance it has never had any real issues since I have had it. However, maybe a week and a half ago when I got up to go to work the car wouldn't start. It would turn over, but would never actually start. When I got home from work later in the afternoon I tried again and it was fine. It's been doing this and progressively getting worse ever since.
If I go to start it in the morning, nothing. Wait until 10-11 or so and it'll run in one attempt. What's strange is that temperature does not seem to affect this issue. Some nights I will go out to drive after it has cooled down outside (70 degrees or so) and it will start no problem. Some mornings it's already 80 degrees and I still have no luck.
I have pulled the following DTCs, which keep reappearing after I clear them, making me believe this is an electrical issue:
P0261, P0267, P0270, P0264, (all 4 cylinder injector circuits low) P0445, P0037, P0418, P0010, and P0414.
So far I have replaced both the Secondary air injector relay and ECM relay, pulled and checked every fuse in the car, cleaned the battery terminals, and am about to go out and check every ground.
Having trouble starting my car after getting gas on a low tank. It had appeared to me this was the only time and maybe it was at the time but now I've noticed it happens whenever I turn the car off after its warmed up and been driven and have it left off for several minutes and try to restart it. If I just turn it off and try to turn it back on immediately it will start fine, or if it is left off for 10 minutes or more it will be fine to start back up. It always starts when cold. The jetta is a 2003 1.8t manual transmission, I always let it idle for a short period after driving, longer if driven hard before shutting down. It was suggested to replace the evap purge valve which I did and it has not fixed the issue. Another piece I have replaced recently is the crankshaft position sensor which was to resolve a random stalling problem.
View 10 RepliesMy Daughters jetta will at time no start after it has been locked then unlocked. She told me that if the car doesn't beep when locked she sometimes has the problem.
The dash will light but no crank at all. Could this be an alarm issue or something else? I found others having a similar issue on Google but no fix or confirmation of the cause.
My car was running fine and it was due for a new oil change so I decided to do it myself. I changed the oil and oil filter and I started my car after I did this and it ran fine. I shut my car off and a few minutes later when I went to start it again, it cranked over and was sputtering. I tried again and now it won't even sputter. It will just turn over. Also the car is a 03 vw gti vr6 with 126xxx miles on it.
View 24 RepliesI am having a problem starting my VW Golf 2.0 since yesterday. When i turn on the ignition the car cranks up but does not start. I did a computer odb check and it gave me out some error codes.
here are a few things that i noticed sometime back:
While driving once or twice suddenly the car wasn't accelerating when i pressed the accelerator. This happened to me twice but then it was OK. Didn't have an issue again.
Sometimes the car gear doesn't shift gear i have to shutdown the car and start it again, then it shifts gear properly. I feel like the car is consuming a bit extra fuel. How I can fix this and what the issue is?
I have a 2003 2.0 gas Jetta (181k miles, automatic.) that won't rev over 3k, starts rough, idles rough and wont stop setting a P0341 cam position sensor code.
The car was not running when I got it, I replaced the coil pack and it ran but not over 3k. Cleared codes, it sets the P0341 immediately.
Had timing belt, water pump, tensioner and cam pos sensor replaced. Still, sets p0341 code, starts rough, idles rough and wont rev over 3k.
The throttle servo makes a little noise when actuated, shop thinks this is my demon - suggests replace throttle body. This car is for my son who will be taking it to college soon.
What this sound is / caused by? This is my Dad's Golf, the sound subsides after the engine warms up a little. It runs fine, power and all. I took off the top timing cover, nope that wasn't it, no rubbing as the sound persisted. Thinking maybe an injector o-ring? The car has 130,000 miles and change on it.
[URL] ....