Golf IV / Jetta IV :: 2004 - P0411 Code / Secondary Air Injection System Incorrect Flow


May 7, 2014

2004 VR6 24v ... I had another thread about my son's car stalling after driving about 20 miles and then running good again after letting it sit for a couple of hours. Anyway I changed the Crank Position Sensor and I have been driving it work and back the last couple of days so I am starting to relax that the CPS fixed that problem. Won't be positively sure for a while as the problem took a while to occur. So far so good.

While coming to work today the car picked up the P0411 code, secondary air injection system incorrect flow. When I changed the CPS sensor i unbolted a module underneath the car by the oil filter to get better access to the CPS. I did not remove it, just unbolted it so I could push it out of the way about and inch.

After putting it all back together and driving it for several trips with no stalling this P0411 comes on. Is that module I moved the Secondary Air Pump and could I have disturbed something. I will check it when I get home. How critical is that code. I read where it works to warm a cold engine. What effect would there be driving with that code?

View 5 Replies

Advertisement

Golf IV / Jetta IV :: CEL Code P0411 Secondary Air Injection System Incorrect Flow Detected

I got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.

View 4 Replies

Golf IV / Jetta IV :: 2003 1.8 Turbo Throwing P0411 - Secondary Air Injection System Error

I keep throwing a P0411 - Secondary Air Injection System error. My previous pump was seized so I replaced it, and broke a few of the chintzy air hoses in the process. Now, with new pump installed and new air hoses connected, I can go about 5 days before the code comes back on.

So to recap, I have:

Replaced the air pump

Verified the new air pump functions, yepReplaced the air hoses

Verified connection of air hoses at all junctions

Checked the Secondary Air Relay for function

I have not yet checked the solenoid - unsure how to do so.

View 2 Replies

GTI 337/20th Anniversary :: 2005 GLI 1.8t - Secondary Air Injection System / Incorrect Flow Detected

Chassis Type: 9M - VW Jetta IV
Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75 76

Address 01: Engine Labels: 06A-906-032-AWP.lbl
Part No: 06A 906 032 RN
Component: 1.8L R4/5VT G 0001
Coding: 07510
Shop #: WSC 00066
3VWSE69M14M129075 VWZ7Z0D9541648

1 Fault Found:
16795 - Secondary Air Injection System: Incorrect Flow Detected
P0411 - 35-00 - -
Readiness: 0000 0000
-------------------------------------------------------------------------------
Address 56: Radio Labels: 3B7-035-1xx-56.lbl
Part No: 3B7 035 180 G
Component: RADIO 3CP 0007
Coding: 00031
Shop #: WSC 00066

1 Fault Found:
00856 - Radio Antenna
36-00 - Open Circuit
End ---------------------------------------------------------------------

View 15 Replies

Golf V R32 :: Code P1414 And P1424 / Secondary Air Injection System Leak Detected

Secondary air injection system leak detected-Bank 1 & 2... 2003 miles on my car and the CEL pops on this morning. VCV bodies are being replaced tomorrow. The tech didn't fully understand what parameters to test for or what conditions would be present to set this code, I can't say that I do either... the flapper could possibly play a role in this..?

View 5 Replies

Golf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow

I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..

View 9 Replies

Lexus GX 2004-09 :: 2005 - Code P2441 - Secondary Air Injection System Switch Stuck

120K miles - love the car

CEL, skid, VSC trac and VSC off lights on - dealer said the code was p2441 Secondary Air Injection System switch stuck. Dealer said I needed to replace air injection system and that the cel would not go off until it was repaired. They completed the 120K service and when I picked it up, all the warning lights were off. I have driven it a couple of hundred miles since then and still no lights. Does that mean it could have been something else???? I love the car, but I need tires and brakes and now repair charges for a 2005 car with 120K.

View 14 Replies

Golf IV R32 :: Code P0441 - EVAC Control System / Incorrect Flow

Check engine light came on the other day. Brought the car over to autozone and this was the code that came back. P0441 EVAC Control System; Incorrect flow. Where I should start looking?

View 3 Replies

Santa Fe (CM - 2007-12) :: P0441 CEL Code - Evap Emission System Incorrect Purge Flow

Just received a P0441 CEL (Evap Emission System Incorrect Purge Flow). I have a 2.7l engine, 2WD. I've read other forums and it seems it's most likely the purge valve or charcoal canister.

View 7 Replies

Santa Fe (CM - 2007-12) :: CEL On With Code P0441 - EVAP Emission System Incorrect Purge Flow

I've had the check engine light come on and was told it was probably from topping up too much and that it would go off on it's own... I should say I have no issues with idle or rough starts.

I had it scanned at Auto Zone. The print out shows: "EVAP emission system incorrect purge flow probable cause

1) Faulty purge control solenoid
2) Faulty vent solenoid
3) Blocked vapor canister

Previous posts suggest if it were a blocked vapor canister I'd have trouble completely filling the tank so I am hoping it's one of the others. Almost everything I see suggests the purge control and that looks like an easy fix. My concerns are a) if it is the vent solenoid - how hard is that to get at and b) what is the part number as I can't find it listed anywhere? I want to have both on hand before I start trying to fix this. Lastly if it is the vent solenoid should I just give up and see a dealer??

View 3 Replies

Phaeton :: Secondary Air Injection System Fault Codes

My 2006 W12 has been trouble free since taking delivery over a year and a half and 30K miles ago. Just broke 60K total miles over the weekend and the engine light came on. I have pasted the scan below. I cleared the codes and drove about 500 miles before the MIL reappeared. I have read this thread: [URL] ....

My first question is: Is there any harm in continuing to drive it?

I have visually inspected the secondary air injection system hoses and can't find anything glaring (no kinks, leaks, disconnections). I am open to taking the car to the dealership but I have low confidence in their diagnostic capabilities. I am fine with them doing work once we know what is wrong but I want to tell them what to do (replace a bunch of hoses for example). How to proceed?

Address 01: Engine Labels: 07C-906-018-BAP1.lbl

Part No SW: 07C 906 018 AJ HW: 000 000 000 00

Component: D1-6.0L-AT-LEV2 G 6722

Revision: --H01--- Serial number: VWZ3Z0E5400307

Coding: 0000173

[Code] ....

View 19 Replies

Lexus GX 2010+ :: Secondary Air Injection Valve Failure - Code P2440

Just got the dreaded p2440 code which is the secondary air injection valve failure. Not only do you get several lights on the dash, you also get limp mode with this code.

My GX is a 2011 with 46k, and even though several Toyota vehicles have had their warranty extended to 10yr 150k for this very system, Lexus has done no such thing.

The dealer was very familiar with this issue and knew it wasn't covered under any existing warranty. He said it's "around $2000" to fix because one of the valves is still under the intake manifold.

Even though I hate to "RIG" my GX, I ordered the bypass module from EBAY. It blocks the system off and tricks the ecu into thinking all is well.

For those not familiar, this system runs on cold starts for 30 seconds or so to warm up the cats, it has no other function.

View 12 Replies

Ford Wiring/Electrical :: 1997 E350 - MIL Code 4011 - Insufficient Secondary Air Injection

My 97 E350/460ci occasionally sets trouble code 4011. It clears every time I check it with my code reader. Something about insufficient secondary air injection. The dealer ship couldn't duplicate/diagnose the problem. Maybe something with the air injection solenoids.

Otherwise, it runs fine. I did notice on the passenger side of the engine compartment a large black metal filter looking thingie with about a 3/4" outlet that doesn't have any hose on it or seem to go anywhere else. Once in a while when you start it i hear a sort of soft popping noise for a few seconds that I would associate with the air pump.

Also can't get the ABS light to go away. It's out when you start it but as soon as you get going it comes on. I flushed the fluid and replaced the rear sensor to no avail. Also tried to flush out the front tone wheels and sensors.

View 3 Replies

Golf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411

Alright so my car is popping up 4 codes.

P0411 - Secondary Air Injection System Incorrect Flow Detected

P0300 - Random/Multiple Cylinder Misfire Detected

P0302 - Cylinder 2 Misfire Detected

P0303 - Cylinder 3 Misfire Detected

Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)

The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.

I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?

Things I have done so far:

-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean

Things I will do after work today:

-Check the spark plugs
-Check spark plug cable for damage

View 5 Replies

GTI 337/20th Anniversary :: Increased Air Flow In Secondary Air System?

I just threw a check engine light saying that there was increased air flow in the secondary air system...what does that mean????

View 15 Replies

Golf IV / Jetta IV :: Error Code P0411 Causing The Car To No Start

I have a 2005 Jetta 1.8t and the thing will not start! The battery is fine, and has been recharged 100%. The fuel pump is pumping. It cranks all day, but just won't start. The only error code i'm getting is a P0411 which I understand is a leak in the vacuum system somewhere.

View 5 Replies

Golf IV / Jetta IV :: Check Engine Light Came On - Code P0411

Just installed a short Ram intake on my 2000 Vw Jetta 1.8t. Had the Intake for about 250 miles and now the check engine light came on. Just pulled the code p0411 secondary air injection system incorrect flow detected. Is this just cause there is more air going through the MAF sensor?

View 11 Replies

Golf IV / Jetta IV :: Error Code P0411 - Car Won't Triggers Quickly After A Reset

Whenever P0411 triggers for me, it is very late into driving (i.e. like 30 minutes into the freeway type of situation) where the engine has already hit optimal temperature. I've gone 1000 miles after reset before it triggers. Sometimes 200 or so miles, but it never triggers quickly after a reset. I'm unsure if it matters, but the VR6 does have a cold air intake (and I do have the breather hose connected & maf correctly connected). I'm pointing it out because p0411 became an issue about 500 miles after I had installed the cold air intake.

View 6 Replies

Toyota - Camry :: Evaporative Emission Control System Incorrect Purge Flow

The check engine light on my 99 Camry went on at about 180,000 miles. My mechanic checked the code and turned up an EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW He said this could be any number of things,including the need for a gas cannister or some type of valve. What does this mean? How do you determine exactly what the cause of the problem is? What are the likely fixes? Will Toyota be able to better determine the cause than my personal mechanic? What are the best options?

View 5 Replies

Accent RB (2012+) :: CEL Code P0441 - Incorrect Purge Flow

My accent currently has just under 17k and about two months ago displayed a cel. I plugged in my innova 3100 code scanner and it displayed p0441. saying it was incorrect purge flow. My question is.. is this covered under the factory warranty. I'm on a very tight budget and I'm trying to find out before going in and finding out. I've owned Hyundai's since 2002 and so far have never paid for an out of pocket repair. But it doesn't hurt to check ahead.. And I've already gotten the standard "it's your gas cap". Ok I'd buy that if it was 10yrs old but it's only a yr and a half old. besides it only goes half a turn then clicks. so it kind of either seals or it doesn't.

View 3 Replies

Golf IV / Jetta IV :: 2.0 Auto Transmission - Code P0730 Incorrect Gear Ratio

Just picked up a 2002 golf 2.0 auto for $200. Get the car home start it up and it runs great but... transmission shifts all kinds of funky. Starts in first then shifts to third. If I give it some gas it shifts down to second but has nothing there, just revs. Will not go into 4th at all. Throw my little mac scanner on it some codes come up. Only one that mattered was p0277 if I remember. Do a little search and it comes up as the g68 under the tranny mount. Change that out and had not cel. Still shifting the same but no code at all. Throw my scanner on just to see and get p0730 incorrect gear ratio.

View 2 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved