GTI 337/20th Anniversary :: 2005 GLI 1.8t - Secondary Air Injection System / Incorrect Flow Detected
May 19, 2010
Chassis Type: 9M - VW Jetta IV
Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75 76
Address 01: Engine Labels: 06A-906-032-AWP.lbl
Part No: 06A 906 032 RN
Component: 1.8L R4/5VT G 0001
Coding: 07510
Shop #: WSC 00066
3VWSE69M14M129075 VWZ7Z0D9541648
1 Fault Found:
16795 - Secondary Air Injection System: Incorrect Flow Detected
P0411 - 35-00 - -
Readiness: 0000 0000
-------------------------------------------------------------------------------
Address 56: Radio Labels: 3B7-035-1xx-56.lbl
Part No: 3B7 035 180 G
Component: RADIO 3CP 0007
Coding: 00031
Shop #: WSC 00066
1 Fault Found:
00856 - Radio Antenna
36-00 - Open Circuit
End ---------------------------------------------------------------------
View 15 Replies
Advertisement
I got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.
View 4 Replies
2004 VR6 24v ... I had another thread about my son's car stalling after driving about 20 miles and then running good again after letting it sit for a couple of hours. Anyway I changed the Crank Position Sensor and I have been driving it work and back the last couple of days so I am starting to relax that the CPS fixed that problem. Won't be positively sure for a while as the problem took a while to occur. So far so good.
While coming to work today the car picked up the P0411 code, secondary air injection system incorrect flow. When I changed the CPS sensor i unbolted a module underneath the car by the oil filter to get better access to the CPS. I did not remove it, just unbolted it so I could push it out of the way about and inch.
After putting it all back together and driving it for several trips with no stalling this P0411 comes on. Is that module I moved the Secondary Air Pump and could I have disturbed something. I will check it when I get home. How critical is that code. I read where it works to warm a cold engine. What effect would there be driving with that code?
View 5 Replies
I just threw a check engine light saying that there was increased air flow in the secondary air system...what does that mean????
View 15 Replies
Secondary air injection system leak detected-Bank 1 & 2... 2003 miles on my car and the CEL pops on this morning. VCV bodies are being replaced tomorrow. The tech didn't fully understand what parameters to test for or what conditions would be present to set this code, I can't say that I do either... the flapper could possibly play a role in this..?
View 5 Replies
120K miles - love the car
CEL, skid, VSC trac and VSC off lights on - dealer said the code was p2441 Secondary Air Injection System switch stuck. Dealer said I needed to replace air injection system and that the cel would not go off until it was repaired. They completed the 120K service and when I picked it up, all the warning lights were off. I have driven it a couple of hundred miles since then and still no lights. Does that mean it could have been something else???? I love the car, but I need tires and brakes and now repair charges for a 2005 car with 120K.
View 14 Replies
My 2006 W12 has been trouble free since taking delivery over a year and a half and 30K miles ago. Just broke 60K total miles over the weekend and the engine light came on. I have pasted the scan below. I cleared the codes and drove about 500 miles before the MIL reappeared. I have read this thread: [URL] ....
My first question is: Is there any harm in continuing to drive it?
I have visually inspected the secondary air injection system hoses and can't find anything glaring (no kinks, leaks, disconnections). I am open to taking the car to the dealership but I have low confidence in their diagnostic capabilities. I am fine with them doing work once we know what is wrong but I want to tell them what to do (replace a bunch of hoses for example). How to proceed?
Address 01: Engine Labels: 07C-906-018-BAP1.lbl
Part No SW: 07C 906 018 AJ HW: 000 000 000 00
Component: D1-6.0L-AT-LEV2 G 6722
Revision: --H01--- Serial number: VWZ3Z0E5400307
Coding: 0000173
[Code] ....
View 19 Replies
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 Replies
This is the code i pulled from Vag. Its not the gas cap...
VCDS Release 805.0: Generic OBD2
Mode 03: Emission related fault codes
Address 10 (Engine): 1 Fault Found:
P0456 - EVAP System: Very Small Leak Detected
View 8 Replies
I keep throwing a P0411 - Secondary Air Injection System error. My previous pump was seized so I replaced it, and broke a few of the chintzy air hoses in the process. Now, with new pump installed and new air hoses connected, I can go about 5 days before the code comes back on.
So to recap, I have:
Replaced the air pump
Verified the new air pump functions, yepReplaced the air hoses
Verified connection of air hoses at all junctions
Checked the Secondary Air Relay for function
I have not yet checked the solenoid - unsure how to do so.
View 2 Replies
Check engine light came on the other day. Brought the car over to autozone and this was the code that came back. P0441 EVAC Control System; Incorrect flow. Where I should start looking?
View 3 Replies
The check engine light on my 99 Camry went on at about 180,000 miles. My mechanic checked the code and turned up an EVAPORATIVE EMISSION CONTROL SYSTEM INCORRECT PURGE FLOW He said this could be any number of things,including the need for a gas cannister or some type of valve. What does this mean? How do you determine exactly what the cause of the problem is? What are the likely fixes? Will Toyota be able to better determine the cause than my personal mechanic? What are the best options?
View 5 Replies
Just received a P0441 CEL (Evap Emission System Incorrect Purge Flow). I have a 2.7l engine, 2WD. I've read other forums and it seems it's most likely the purge valve or charcoal canister.
View 7 Replies
I've had the check engine light come on and was told it was probably from topping up too much and that it would go off on it's own... I should say I have no issues with idle or rough starts.
I had it scanned at Auto Zone. The print out shows: "EVAP emission system incorrect purge flow probable cause
1) Faulty purge control solenoid
2) Faulty vent solenoid
3) Blocked vapor canister
Previous posts suggest if it were a blocked vapor canister I'd have trouble completely filling the tank so I am hoping it's one of the others. Almost everything I see suggests the purge control and that looks like an easy fix. My concerns are a) if it is the vent solenoid - how hard is that to get at and b) what is the part number as I can't find it listed anywhere? I want to have both on hand before I start trying to fix this. Lastly if it is the vent solenoid should I just give up and see a dealer??
View 3 Replies
I have a question? I have had my car parked for about 2 1/2 months and I just started it this weekend and I've always noticed on our cars when we start them in the morning I think it's the secondary air pump that turns on, it sounds like a blow dryer.. It only stays on for about 10 seconds maybe. Cause when I started my car this weekend I didn't hear come on.
View 3 Replies
Have a little oil on the outer part of the turbo and its making a raspy noise when my turbo is spoiled not sure whats going on the car pulls just as hard and boost levels are normal i had a check engine light on for a few days right after this started code was for p0411 dont think its related cause i know my secondary air pump whistles at cold start so im assuming that the code is for that and not related to the turbo.
View 1 Replies
I put in a new sensor to stop the problem but now I have the code 00778 which is steering angle sensor and then says 005 no or incorrect basic settings/adaption. I went through the Ross-Tech site to reset the code in group 60 and activate the basic settings, but I am then told that group 060 is not available. I have tried to set the steering wheel angle straight but the angle still says its at 349.47*. My car is a 2004 Jetta GLI 1.8T.
View 4 Replies
Where the secondary air injection pump is? I'm getting P1411 & P1423 codes.
View 4 Replies
I have a beautiful 1996 Saab, 900s. Recently the check engine light came on and at Autozone they said the code was for the secondary air injection pump. I took it to a new mechanic, he checked it out and called me to say the pump itself was broken and would cost 1,000 to fix. I said that was a lot, and would think about it, and picked up my car.
Strangest thing- the check engine light is now off! Is this normal? And I just took the car in for the state inspection, it passed! I was under the impression a car without a working secondary air injection pump can't pass emissions. What is going on here??
View 9 Replies
Finally getting to my header and exhaust install.
I plan on removing the secondary air injection as I have no provision for it. Will this throw a CEL?
Looks like it goes into a rubber hose and comes around to the top of the intake manifold.
What is the best/cleanest way to cap this off?
View 5 Replies
Just got the dreaded p2440 code which is the secondary air injection valve failure. Not only do you get several lights on the dash, you also get limp mode with this code.
My GX is a 2011 with 46k, and even though several Toyota vehicles have had their warranty extended to 10yr 150k for this very system, Lexus has done no such thing.
The dealer was very familiar with this issue and knew it wasn't covered under any existing warranty. He said it's "around $2000" to fix because one of the valves is still under the intake manifold.
Even though I hate to "RIG" my GX, I ordered the bypass module from EBAY. It blocks the system off and tricks the ecu into thinking all is well.
For those not familiar, this system runs on cold starts for 30 seconds or so to warm up the cats, it has no other function.
View 12 Replies
