Golf IV / Jetta IV :: Rough Idle / Small Hose Behind MAF In Front Throttle Body Split In Half
Sep 14, 2015
I searched but couldn't immediately find anything about this particular line. I've been struggling with a rough idle for the past couple weeks, throwing codes that I'm running to lean all the time. I cleaned the throttle body and MAF, and was in the process of replacing the MAF and noticed a small hose fitting behind the MAF but before the throttle body was pretty much split in half. I don't know what it's for and I'm replacing it regardless, but could this be the source of my problem?
View 5 Replies
Advertisement
The inter cooler to throttle body hose and it seems to have coolant all over it.
View 12 Replies
Having problems with a ECM and throttle body for 2010 Corolla S? My corolla will idle rough and the throttle body will shut the car down to where it is inoperable. It throws codes and shuts the VVT down. The car currently has 56k miles on it and has been to Toyota 3 times in 3 months.
The first time they say they replaced the ECM, I really don't think so. 24 hours after we picked the car up it shut down again. The second time we brought it back in they said the brake light bulb caused the throttle body to shut down.
It had to go back again this week after it shut down again in traffic when it was idling. Toyota said the throttle body had to re-learn the idle again from when the ECM was supposedly replaced.
View 5 Replies
Few weeks ago.....Prius was showing the P0505 code .... Mechanic, ran diagnostics and determined it was dirty TB. Cleaned TB.....cleared the code (inspected PCV...hoses).
When I initially picked it up it was revving very high....so he hooked it back up to the scanner and did some type of "reset" for the idle (this cleared most some computer settings...back-up beep, radio stations, etc...). Everything ran fine for past 3 weeks...
Just last night..... started running rough again. What I noticed this morning ... Started it up and it ran very rough til the auto shutdown after warmup (no warning lights). Then....when I started driving slowly out of the lot...it ran "rough upon acceleration"...... Then fine at cruising speed. Same behavior at every light....rough acceleration.... fine once up to speed. Just started it up again and same behavior.....(does not die...just very rough).
View 19 Replies
Trying to clean the throttle body on my 09 sonata 2.4L due to rough idle occasionally (throwing P0106, replaced MAF sensor still same problem), one quick question, is it okay to force the valve open (with connector disconnected of course), and is "re-learning" necessary and what's the proper way to do it?
View 2 Replies
I decided to take out the throttle body and clean it with throttle body cleaner that I got from autozone, after I put everything back, I started my car and the motor was shaking and smoking a lot out the muffler and just would not be drivable at all. the RPM was just going up and down and hesitating bad. later I took off the spark plugs and they were very much burnt black at the tips and that is probably not normal right? but I replaced them with NGK BKR7E spark plugs and it still gave me the problem.
View 13 Replies
I have a customer that has a 2.0 mk4 with 260000 miles on it..about 20k miles ago we had 6 codes saying throttle body was not working and car was surging, so we ordered a vdo tb, installed it reset tb and it ran fine for 7 months and 20k miles. Again car is surging, so i tried a tb reset. tb was under guarantee so we took advantage and replaced it/reset it and it threw a code within 5 min of driving and hesitating/surging. He is original owner? possible ecu getting sleepy?
View 22 Replies
So the other day I went to the mechanic for him to see what code(s) were causing my CEL. He simply told me that there was an issue with the throttle body and it didn't know what position to be in; he cleared the codes, clean the throttle body and said if the light came on again I needed a new tb. The CEL came back on, but his diagnosis doesn't make sense to me.
From what I've researched if the throttle body had this issue the car would run like crap; however, it runs fine. Smooth idle, good throttle response, accelerates smoothly through the rev range, and I'm still getting decent fuel economy. Given that, it doesn't seem like it's the TPS either, and the tb was just cleaned so I'm confused. Could it actually be the throttle body, or is there some sensor that has just gone bad? The car is a 2000 Golf with an AEG engine & 5-speed box.
And here are a couple pic for clicks of a stock-ish car.....
View 5 Replies
I have a great running 98 Windstar. It does not overheat. The oil looks like it needs to be changed but it is not Coffee Colored, as the picture. The PCV valve looks clean, and rattles. I replaced the small 2 inch hose at the PCV valve on the back valve cover since it looked weak in the middle and may have been collapsing. I no longer get the big puddles of OIL/WATER on the ground, that I use to. I cleaned the oil/water out of the Intake Hose of the Throttle Body, but I still see some of the mixture underneath the Air Instake hose after a long drive.
I will go by the Ford dealer and buy another PCV valve, and replace the small curved hose going to the top of the engine near the Throttle Body that the other end of the PCV connects. Someone suggested that this could be cracked, and it does have some small cracks in it at the bend.
I have read that the 99-00 had a design problem with the Valve Cover, and it allowed oil to be sucked out and give similar problem. But since this is a 98, I am just looking for pinched hoses, or leaks. Car runs great, and hoping that I can find the reason that oil is being sucked into the air intake.
Do I have it correct that during normal operation, that the moisture and gases are sucked up out of the engine thru the PCV and into the top of the engine. And that the other Valve cover hose is going in the other direction or from the throttle body to the Valve cover?
Just trying to determine if the oil/moisture mixture is coming from the front or rear (PCV) valve cover. Getting no codes on the engine.
View 14 Replies
I have been having the dredded EPC light coming on and according to the vag scan its the throotle body. What I need to know is if one off a 2003 2.0 jetta will work on my 2004 2.0 jetta. The number on the side of mine 06A 133 062s is not the same number on the 03. I was told that they must match to work properly.
View 2 Replies
I have a 2001 vw jetta 2.0 and I was accelerating on the interstate the other day and the car just started bogging down and now the car only accelerates slowly at partial throttle any more and it makes a loud intake noise and bogs down also the car idles bad and even at partial throttle the car struggles to get above 3k rpm, I scan for codes and got MAF, O2 sensor before the cat and camshaft position sensor, I replaced the camshaft position sensor and car still runs like crap, what is the problem??
View 4 Replies
I have a really small leak coming from the lower end of my power steering hose, it's super small, I was wondering if I could fix this by wiping it down really well and dry, and then layering it with plasti-dip. I think the leak is small/slow enough for me to get in a few good layers. Would this be an okay fix, or would the plasti-dip separate fast?
View 2 Replies
I have got a 5 door 2002 Golf 1.6l petrol, manual transmission with 190k kilometers on the clock. It has been playing up recently and the authorized VW garage is clueless, but still happy to charge for a miserable job...
The "symptoms" are always the same: I can start the car no problem. Plenty of water coming out of the exhaust and EPC light comes on, no power transmission (or very little). In this state, the engine runs irregular. Before all this happens, you can tell there will be a problem (this is not super obvious), as the car does not run smoothly in neutral, especially when it is at a a hill You might get away with another 50k but that's it.
Breakdown 1: Called out road side assistance and got it towed. Volkswagen dealer retrieved the error code P1564 and they replaced the throttle and some of the contacts of the throttle. (Costs 800 GBP)
Breakdown 2: However, 300 km later, same problem as before road side assistance retrieved error code P0638. The memory was reset and it did run perfectly fine for a short while (2000 km).
Breakdown 3: As before, error message P1564 was read. This time they thought there was a problem with the coil in cylinder 2 and replaced it (250 GBP) - also the one in cylinder 1 as "old". Picked up the car and it was not running smoothly in neutral and it eventually broke down after only 90 km.
What to get changed next? What is the real root of the problem here?
View 2 Replies
I have narrowed down my starting issue to a faulty relay(409). When I pulled the relay and cleaned the contacts and reinstalled the pump primed and the car started. Car will idle for about a 1/2 hour and out of the blue it shuts off. If I try to restart, 9 times out of 10 it does not start. If i tap the relay, it starts right up. If the car is running and I tap on the relay the car stutters and if I tap it again it shuts off.
View 10 Replies
I have a 2004 V6 LE with about 135k miles. I cleaned the throttle body two weeks ago, just because I hadn't ever done it. It wasn't too dirty. Before the cleaning, it idled at < 1k revs. Now, when I start the engine cold, it revs at around 1500, sometimes higher. It goes back to normal after the engine warms up to operating temperature.
Also, I hear a very slight high-pitched whining (maybe hissing?) noise when I accelerate. The noise is more prominent when the engine is cold. I checked for vacuum leaks but couldn't find any.
It feels like I'm depressing the gas pedal a little bit when I have it in drive or reverse, and it wants to pull harder than usual. When I bring the car to a stop with light brake pressure, as it drops into first gear, the car gives a slight tug forward, again, as if the gas pedal is depressed. I mention this to show that it's not just an issue with the rpm at startup.
I suspect that the issue lies with the throttle position sensor, which I may have jostled when I moved the throttle valve. The method I used when cleaning was, I first tried opening the valve by hand with the ignition off, but the resistance was much higher than I had anticipated. So I did the key-in method by turning the ignition to ON and putting a brick on the gas pedal. There was a high-pitched whine coming from somewhere in the engine bay when the key was ON, which I had not noticed before; I wonder if that is normal.
This seems to be a rather common issue after cleaning the throttle body cleaning, but there doesn't seem to be any consensus solution besides to wait it out.
View 6 Replies
2002 Camry XLE.
I cleaned my throttle body today. Since the throttle plate moves by a motor, in order to keep it open, I turned the key to ON and held the gas pedal down by using some weight.
After I put everything back, the idle was high 2000+, then stays at 1300 to 1400 range. I drove about 10 miles and it is still the same. When stopped at a light in drive, the idle is still 1000
Did I mess up the e-throttle or the throttle position sensor? (Since I used a weight to hold the gas pedal down, I am worried now).
View 5 Replies
2002 V6 Camry 145,000 miles, cleaned throttle body with TBC fluid, now starts runs for a few seconds and dies. In order to open the butterfly in cleaning I turned ign on and propped pedal down. After cleaning the car ran better but idle was high and a little erratic. I disconnected the neg batt for several hours, now it starts, but dies right away. In the cleaning process I had removed the throttle control sensor an reinstalled it. Can't keep it running long enough to adjust it.
View 8 Replies
I recently cleaned the throttle body and now it surges up and down. Not really sure what to check next. 2002 toyota camry 4 cyl.
View 3 Replies
I cleaned my daughters throttle body on her 2005 prius. Sprayed it down on the vehicle trying to fix my P0505 code and now its idling high. Is there a learn procedure to reset this after service.
View 6 Replies
I finally finished installing my VF stage 2 supercharger. I fired it up and the idle is low (around 500 rpms) and a very rough idle. Throttle response is very slow, when it finally revs the car stalls. I can also hear a leak somewhere near the throttle body. I have an SAI block off plate. 630cc injectors and UM tune. No CEL
View 3 Replies
I have a 2009 Camry which has the well known very bad vibration at idle when in drive at a light. My Ultragauge shows the RPM are very low when it vibrates. Sometimes it drops to around 425-450 rpm when at a stop light in drive (automatic car). Then it sometimes moves up to around 625-675 rpm and that is when the vibration completely disappears and it is nice and smooth. This issue is intermittent but happens everyday.
Most people think it is due to a bad engine mount and spend money doing that and get no results.
I have done a lot of research and feel it is due to a dirty throttle body and IAC valve and want to test my theory. I will post results once I do the job. What is the easiest and most thorough way to clean both?
View 6 Replies
