Golf IV / Jetta IV :: Whistle Under Acceleration / Sensor Located On Intake Tube
Sep 30, 2015
I have a 02 2.0 Jetta with 179k
Have that pesky "whistle under acceleration" when past 1/4 throttle issue. I have been going over the entire engine, checking and cleaning.
-----On the intake tube where the 1 inch case vent and half inch tube meet there is a Flapper/Flow check with a electrical connector directly on top.
Question being, is this a flow sensor? The flapper is distorted and does not function properly.. is this an issue?
View 2 Replies
Advertisement
Looking at my circle track car when they told me my air intake temperature sensor was missing this is a picture online I found: [URL] ....
The hole is filled with a bolt and some epoxy. I don't see where the cable is for it. What will this do to my car? It is a track only car.
View 6 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
View 2 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....
View 3 Replies
Well yesterday i installed the Neuspeed Intake and had no trouble what so ever until 30 min ago when i pull out of the parking lot abit harsh but nothing extreme no wheel spining or anything like that just a bit quicker exit.
That's when my check engine lit up and i pulled over and checked what was going on and heard a air leak, which is located to the left of the intake filter.
View 9 Replies
So i have been hearing a whistle under acceleration for some time. Normally comes at 1/2 to full throttle. I also have had check engine light for a bad o2 sensor for about the same amount of time(2months). Fast forward to last week. finally replaced sensor. Check engine is gone. Open her up a little on and on ramp, Whistle is still there and the CEL comes back. Have it scanned, and it come back load calculation cross check 17551. I need an sticker so i rest the ecu (no light) and drove it like a grandma 50miles to get the sticker. No CEL. Get sticker. Just to make sure i wasn't crazy i gave her some gas on the way out of the inspection lot, and there is the CEL.
In conclusion, Between the whistle, CEL, and the fact that i drove it 50 miles with out the CEL coming back under very light throttle, and i just replaced the MAF with a new Bosch 2 months ago, i am pretty sure it is some kind of vac leak.
I have a new TB gasket in the mail, but my question is, Is there other places where such a vac leak is common in these cars? Other info on car.
UM tune
evoms intake
HPA downpipes (whistle started after these where installed)
Flapper
no res
74k on the clock
View 11 Replies
Temp is at 190, runs great, coolant levels are fine, everything seems fine but there's a constant stream of smoke coming from my dipstick tube. Oil isn't milky. 2.0 AZG. Tried searching but only found threads for 1.8t's. Headgasket was done recently.
View 2 Replies
My new to me Golf makes a strange "whistle" sound around 2000+ RPM. In any gear only when accelerating. My car does not have a turbo so its not that, the sound is coming from the motor it self. Very strange.
I dont think it comes from the tranny or clutch.
Car has 95K miles on it, t-belt and water pump done at 68k (but in 2008!, inspected it and the belt looks fine, no cracks or fraying or anything) This whistle sound is so strange. My wife says it sound like a whistle then it changes to a slight vibration sound.
View 4 Replies
I've tried to do my due diligence searching on this (I've seen many posts but most have other codes).. I have the P000A code, reads as follows-- Intake (A) Cam Position Sensor Slow Response (powertrain).
I have no misfires, hesitation rough idle, nothing. I have 94k miles and I always done my oil changes @ 5k intervals and I have not had any prior engine maintenance done to the car....
I took my R32 to the local VW dealer today and they are saying they believe it might be the time chain tensioners. I am wonder if this could be a simple sensor issue since the car runs perfectly fine, I just get the engine light coming back on after 1 to 2 weeks of clearing the code. I have had this issue since January and I thought it might be the cold weather here in WI.
View 2 Replies
I know it's on the steering column but is it down near the floor or on the engine compartment side?
View 4 Replies
Whistle thru intake. I have a f150 2005 with a 5.4 and it likes to whistle when cold weather when I press the gas it goes away until it idles down?
View 11 Replies
Where the parking assist sensor is in the front. I placed my license plate too far on the left I am assuming and the sensor is going off. For now I have just turned off the PA until after work. (is the PA a small visible circle?).
View 5 Replies
The CEL just came on in my 20th AE Gti. The code indicates a Camshaft Position Sensor issue. Don't know where this sensor lives under the hood of the GTI? Is an easy enough fix for a beginner to attempt? (have hand tools, former bike mechanic, but no shop just a parking lot in the Texas sun!)
View 6 Replies
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 Replies
Just bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.
Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.
Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?
View 5 Replies
I recently noticed a rattling coming from my intake manifold and with little research I discovered it was the intake shifter rod. I ordered the new updated bushings and installed them today and the rod continues to rattle just as bad. My car only has 90k and I am unsure what to do to fix the noise. I am hesitant to order a whole new shifter rod because it could be the manifold itself too worn. I am just curious if there is anything that I may have overlooked or if there is anything I can do.
View 4 Replies
I only removed the standard air filter housing and fresh air intake yesterday to get access to the VSS and Speedo drive to change the differential fluid on my 01M transmission. I was surprised to find that there was a fine metal mesh screen installed at the entrance to this air intake tube. This would be located behind the battery and just behind the drivers side headlight is where this metal mesh screen is located. Anyways, this was easily disassembled to clean and reassemble. However, I did not find anything about this mesh screen in my Chilton's manual, but this is now on my annual maintenance list. I added some pic's to show the clogged air tube. There was also a spring loaded door on this air intake tube...
View 5 Replies
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 Replies
I have a leak where my heater core tube goes into the intake at the rear pass side of engine. I have read that this part is pressed in. I dont want to remove the intake since i just paid $400 to have a new gasket kit put on. My question is can I bypass this tube with a hose from the water pump like in this video?
FORD 4.6 , 5.4 , 6.8, HEATER HOSE UNDER INTAKE REPLACEMENT THE EASY WAY !!! - YouTube....
If I can do a rubber hose like in the video I was to make sure that the tube just goes through the intake and that it does not supple coolant into the intake??
View 13 Replies
I have a 337 with Injen cai. Well, I have since removed the cai due to the fact that rainwater/water during a car wash will run off the hood and onto the top of the inside of the drivers side fender (under hood) and eventually run down onto the filter itself, thus causing it to become water logged. This of course is not good. My question.. I've tried so many things to no avail.
View 7 Replies
After installing my cai, I couldn't find where to put this breather hose, I'm lost to if I need it and where to put it...
View 2 Replies
