Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesEngine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesSo I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).
So my 04 f350 was running fine good power and everything till I shut it off a couple days ago and now when it is cold it fires right up but when the truck warms up it just cranks and cranks .... only code I throwing is p2285
Key on engine off
Ipr-14.8
Icp-0
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine running
Ipr-33.5
Ficm main power-48.0
Ficm logistics-12.5
Icp-875
I thought I fixed it before but I was sadly mistaken replaced the ICP and IPR...
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 Repliesi have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 RepliesTruck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.
First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.
Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.
I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.
Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?
Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?
Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
Stuck turbo and high deltas so I replaced the oil cooler, coolant, thermostat, rebuilt turbo. Etc etc. Now I'm getting p2284/p2285 intermittently. Upon inspection ICP looks great at idle and 2500. IPR at hot idle is 20.9 but when you run it up to 2500, it drops to 14.7 and after a few seconds hpop at idle jumps to 875 and I get the p2284/2285. Bad IPR?
View 14 RepliesI have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesThe service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesThe other day my 07 power troke threw codes p2285 and p2287- ICP circuit low and ICP circuit intermittent. The trucks idle was revving up or bouncing around every so often, not consistently.
I did a visual inspection of both the sensor and pigtail checking for oil but it looks to me like everything is clean and oil free (see pictures). When I unplugged the connector the trucks idol smoothed out and everything ran great!
My questions is what does this indicate? Does this mean my ICP sensor is bad, my pigtail is bad, or there is a short in the harness somewhere?
I have a little over 32k on my 2014. Left today for my first camping trip of 2017. 250 mile into the Eastern Sierras. Took a potty break after 125 miles or so and CEL came on. Used my CTS2 and got a P2201 code which is a NOx sensor. I decided to continue on to my destination and made it there safely.
My question is do you all think I will be ok driving 250 miles back home in a couple of days? Truck seems to run ok. MPG seems to be dropping.
Interestingly, the Soot % on my CTS2 dropped to 0% and stayed there the whole trip. Obviously it's going to the dealership come Monday, just wondering if I will make it home ok and not get stranded in the desert with the family.
So my truck decided to throw out the EBP sensor code. I am noticing a bit of power loss and funny noise when I let off the gas. I am 200 miles from home and not near a town or parts store at the house I am working on. Is it safe to drive the tuck the 200 miles back home tomorrow. I have a very important appointment I can't miss. I will be putting the new sensor and harness on tomorrow Evening
View 3 RepliesI have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 Replies2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 RepliesRight around Christmas. Hubby used the code reader and found this:
U059E - Invalid Data Received from NOx Sensor A
And then cleared it. CEL went away and hasn't been back since, so my question is, am I safe? Was it a fluky reading on a cold day of making short errand runs? Or did I have an actual problem even though the CEL has not come back? Truck is running fine, no issues (knock on wood), and I'm not really worried - just curious more than anything.
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies