Ford 6.0L Power Stroke Diesel :: 2004 F350 Won't Start / CMP Sensor Code
Mar 11, 2016
2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
View 2 Replies
Advertisement
Replace the tft but still the problem, someone cones the number part of tft sensor harness, and as replace , 2006 f350 4x4....
View 2 Replies
I have an 05 f350 6.0 that I recently bought. It was fine until a few weeks ago when it died while I was driving down the road. I pulled to the side and it started right back up like nothing happened and kept driving like normal. Skip to last weekend it did it to me twice but the second time it would not start so I plugged my programmer in and it showed p0336 crank position sensor and cam portion sensor codes (I can't remember the number of the second code) I have read a few posts that said maybe it's the icp sensor so I went ahead and replaced that with no luck. The batteries went dead from excessive cranking which I know isn't very good for my starter but I was getting a little upset.
View 11 Replies
i have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 Replies
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
View 14 Replies
I have a 2004 f350 6.0 powerstroke i recently fixed a oil leak in my remote oil cooler and after I was finished it ran fine and ran fine for a few days I noticed yesterday it had a bit of a rough start and some today but would start and run normal. Started the truck this morning and drove it a bit and then let it sit while I went to the dentist came back out and truck wouldn't start. I am getting 200-330 icp with the ipr cycle at 88.5 ficm sync is good and colts are at 12.5 unplugged icp sensor to see if it would start after that and it disnt start so I ruled that out.
I'm currently waiting on AAA to bring my truck home for me but trying to make sure I'm right to start working on it tomorrow. I am thinking the ipr valve is clogged. Am I right to think this may be the issue? When I first installed my remote oil cooler I had the same issue crank no start turned out to be the ipr valve was gunked up and I ended up replacing it 300 dollars later. Then it started and everything was fine. So basically am I right to start at the ipr valve or should I start somewhere else?
View 14 Replies
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 Replies
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 Replies
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 Replies
I have a 6.0L Powerstroke with about 74k miles. I've owned it about a year. this weekend while driving on the highway at about 55mph i slowed to make a turn. As it came to idle i noticed it was idling real rough. As I accelerated it barely got across the highway. I went to where i was going and let it idle but gave it gas and raised the rpm's to about 1k.
I was concerned it was going to die. As I left it seemed to be better but as i drove it would get real rough and then go away. I accelerated a couple of times engaging the boost and it seemed to be better. I made it home and parked it, but i let it idle before i turned it off.
Now it will not start. it just cranks. everything is pretty much stock. i replaced the fuel filters back in december and also did the blue spring upgrade. I have a OBDII but i didn't have it with me so i wasn't monitoring at the this time. What should be my next step?
View 14 Replies
I have a 04 f350 with 175k on it. At around 160k it had new head gaskets, 2-reman heads, egr delete, new oil cooler and it is studded and tuned with SCT and custom tunes.
Since after the head gasket change it seemed to have started blowing a little smoke on the cold starts mainly. In cold weather the starts seem to be harder or slower also. Now for the last 6k-8k miles there is a little smoke at a cold start. But if the motor is warm and it sits for a bit maybe 10 min or less it blows a nice puff of blue smoke or burnt oil.
The smell of burnt oil is mainly on hot starts not cold starts. It does not burn oil running. It will dump some black smoke under acceleration or load. Could this be an injector problem? Or something else? Can't figure it out.
View 5 Replies
am in possession of my fianc's F350. The battery light kept coming on, I changed both batteries... twice. I pulled the alt and took it to 2 different stores, asking them each to test it twice, and it checks out good. Drove it to a family function in Sept and it died (no lights, no dings, just completely dead), couldn't get it to jump so I had to have it towed. Tow truck driver said it was probably the starter solenoid, but I couldn't get any confirmation. Had a charger/jumper hooked up to it and got gage movement, dings and heard a clicking sound when I tried to start it.... still no jump. Is this a starter issue, or an electrical issue?
View 14 Replies
My nephew has a 2004 F350 that will crank but will not start. It will build oil pressure on the gauge. There is no injector buzz and no communication through OBD2 port. Is the PCM dead?
View 10 Replies
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 Replies
I have a little over 32k on my 2014. Left today for my first camping trip of 2017. 250 mile into the Eastern Sierras. Took a potty break after 125 miles or so and CEL came on. Used my CTS2 and got a P2201 code which is a NOx sensor. I decided to continue on to my destination and made it there safely.
My question is do you all think I will be ok driving 250 miles back home in a couple of days? Truck seems to run ok. MPG seems to be dropping.
Interestingly, the Soot % on my CTS2 dropped to 0% and stayed there the whole trip. Obviously it's going to the dealership come Monday, just wondering if I will make it home ok and not get stranded in the desert with the family.
View 4 Replies
So my truck decided to throw out the EBP sensor code. I am noticing a bit of power loss and funny noise when I let off the gas. I am 200 miles from home and not near a town or parts store at the house I am working on. Is it safe to drive the tuck the 200 miles back home tomorrow. I have a very important appointment I can't miss. I will be putting the new sensor and harness on tomorrow Evening
View 3 Replies
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 Replies
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 Replies
I have a 2011 6.7 F-350 Diesel. I bought the truck new and I've never had any problems with it until now. I have a SCT Chip & Tuner. It needed an update so I returned the truck to stock and a code came up on my dashboard that said "reduced engine power" which obviously I thought was Normal because of the modifications done to my truck.
I updated my tuner and returned the truck to a performance tune but this dashboard code will not go away. My truck isn't reading any codes and there's no other indication lights on. The truck has Normal RPM readings but 0 throttle response. No power at all...
View 2 Replies
Right around Christmas. Hubby used the code reader and found this:
U059E - Invalid Data Received from NOx Sensor A
And then cleared it. CEL went away and hasn't been back since, so my question is, am I safe? Was it a fluky reading on a cold day of making short errand runs? Or did I have an actual problem even though the CEL has not come back? Truck is running fine, no issues (knock on wood), and I'm not really worried - just curious more than anything.
View 9 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies
