The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesI have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
My check engine light popped on for me a couple days ago. P2043-reductant temperature sensor range/performance. Truck still runs like a raped ape, no change in driveability. Just over 21k miles. No "speed limited to 55" messages or anything else. Basically no change in the truck other than the light.
View 12 RepliesMy Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesI'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 RepliesMy engine light just went on and the fault codes are:
P0138 -PowerTrain (O2 Sensor Circuit High Voltage Bank 1 Sensor 2)
P0607 - PowerTrain Control Module Performance
I have just bought Denso 234-4305 Rear Sensor but I was wondering if there are any guides to show where it's located?
The only guides I found is for the 9th Gen Corolla.
The Car has 88k miles on it so I guess it's outside the emissions warranty. Thus what is the price of a new ECU just in case that's the problem?
I have a 2004 f-550 sd with a 6.0. I am having a problem with cyls, 2, 4, 6 and 8 dropping out at idle. if you rev the motor up they work fine. Could I have a bad injector oring? Seems that iap pressure is good. And seems funny that it is just the one side.
View 14 RepliesI have a little over 32k on my 2014. Left today for my first camping trip of 2017. 250 mile into the Eastern Sierras. Took a potty break after 125 miles or so and CEL came on. Used my CTS2 and got a P2201 code which is a NOx sensor. I decided to continue on to my destination and made it there safely.
My question is do you all think I will be ok driving 250 miles back home in a couple of days? Truck seems to run ok. MPG seems to be dropping.
Interestingly, the Soot % on my CTS2 dropped to 0% and stayed there the whole trip. Obviously it's going to the dealership come Monday, just wondering if I will make it home ok and not get stranded in the desert with the family.
So my truck decided to throw out the EBP sensor code. I am noticing a bit of power loss and funny noise when I let off the gas. I am 200 miles from home and not near a town or parts store at the house I am working on. Is it safe to drive the tuck the 200 miles back home tomorrow. I have a very important appointment I can't miss. I will be putting the new sensor and harness on tomorrow Evening
View 3 RepliesWhere is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesI have a question for 11-15 Superduty, regarding the factory option remote door unlock and remote start. How far away does your system operate from?
Mine is good for only 50 ft or so MAX most of the time it won't work until about 15 ft from the truck. Been trying to get the dealer to look into it, but got told today that in the owners manual it is only good to 30 ft. Plus I randomly get a tire pressure sensor fault. The sensors are fine, but since the TPMS and door unlock/ remote start share the same antenna I think the 2 are related.
Since my 2011 would work from 100 yards most of the time I call B.S. on the 30ft. I feel that the new truck should work at least as good as my old one. Besides that 30ft is a complete waste, and virtually useless, in my opinion.
2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 RepliesRight around Christmas. Hubby used the code reader and found this:
U059E - Invalid Data Received from NOx Sensor A
And then cleared it. CEL went away and hasn't been back since, so my question is, am I safe? Was it a fluky reading on a cold day of making short errand runs? Or did I have an actual problem even though the CEL has not come back? Truck is running fine, no issues (knock on wood), and I'm not really worried - just curious more than anything.
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 RepliesI have a 2004 6.0 with 75000 miles on it. My truck is throwing a P0470 code pointing at the exhaust pressure sensor. my question is do I need this sensor or can i bypass it? When I look up the part it only shows 2005 and up.
View 6 RepliesReplace the tft but still the problem, someone cones the number part of tft sensor harness, and as replace , 2006 f350 4x4....
View 2 RepliesWorking on a 2015 f-550 with a 6.7 power stroke. Damaged the wiring harness and fuel gauge not working now. Where could I find a wiring diagram? The low fuel is now causing it to not regen. We have continuity through the wires and they have been repaired but gauge still does not work. Currently now power to fuel gauge sender?
View 1 Replies1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...