Stuck turbo and high deltas so I replaced the oil cooler, coolant, thermostat, rebuilt turbo. Etc etc. Now I'm getting p2284/p2285 intermittently. Upon inspection ICP looks great at idle and 2500. IPR at hot idle is 20.9 but when you run it up to 2500, it drops to 14.7 and after a few seconds hpop at idle jumps to 875 and I get the p2284/2285. Bad IPR?
View 14 RepliesOK, long story short. I had P2284 code on my scan gauge after replacing the oil cooler. I contributed it to air in the oil system. Sure enough, a few days of hard driving and the code went away.
Now a week later, I fired up my truck on a cold start yesterday morning. It's not that cold here(low 40's in the morning), but the oil started off at about 50F. Correspondingly, ICP at is higher, at around 1000(it's like this every morning until oil warms up). I usually let it warm up a tad before driving but yesterday I didn't, and hit the gas pedal a little hard once and the truck started acting like it does when you get this code.
Sure enough, check scan gauge and the code is there. I drive home(about 15 minutes). A half hour later I start the truck up, check codes, and it's back to normal. Of course, oil temps were higher and ICP in the normal range between 580-590.
So is this normal? Since it doesn't trigger a CEL I assume it's more of a system parameters code? Only other thing I can think of, if this isn't normal, is a mucked up IPR screen from when I installed my BPD oil cooler.
I have the later model 2004 F250 6.0 (built May 2004). I have owned it since new. It has 157K miles.
My newest problem comes after I did oil cooler work. I know everyone points to the IPR and/or ICP, but my readings seem strange to me.
About three weeks ago I replaced the oil cooler with a Bulletproof remote unit that uses the factory oil cooler. During the job I removed and installed a new Ford IPR sensor and added the improved screen to it. I removed and installed new Ford water/oil temp sensors, a Ford low oil pressure sensor, and a Ford ICP sensor (in the pax valve cover). I also installed the improved turbo feed line and turbo drain tube. I rebuilt the oil filter/fuel housing and installed new o-rings and the blue spring. I have the dual alternator set-up and had been running the lower alternator unplugged for the last several years. (I know I know). So I swapped in a reman alternator.
I managed start-up after running batteries dead a few times. During the drive I felt idle speed jump up by itself a few times while at low RPM. I felt an unusual skip or two in the motor but the power seemed ok. I accelerated and the truck pulled fine. At highway speed I heard what sounded like the engine hitting a high rev and trying to cut out, but it was very mild. I noticed this first at 2000rpm, but it may have not been pronounced enough for me to notice it at lower RPM. When the cut-out occurred strongest I slammed the throttle down to see if the problem would worsen, but the truck accelerated well with no cut-out, but when I eased off the throttle at higher RPM the cutting out returned. My Banks IQ showed P2284.
I installed 2 new batteries and replaced the ICP pigtail and soldiered it. That had no effect. I put the old ICP sensor back in. That had no effect. I borrowed a Snap-on Solus Edge scanner to test the truck. I would add that the truck starts up as quick as it has always started; 3-5 seconds.
Scanner results:
Key-on, engine off, ICP (voltage) reads .25, IPR reads 15.
During the crank sequence (before engine start), on a freeze frame, RPM is 157, ICP(voltage) reads 1.04, IPR reads 21, ICP pressure reads 768.8 psi. That seemed kinda normal.
Engine running at idle RPM, I read ICP (voltage) 1.2, IPR 15, ICP pressure 863.1psi. That seemed okay.
I drove the truck with a cleared code and noted that something occurred to change my readings. Before the change while driving under a short heavy acceleration to 54mph, I noted these readings: 3533rpm, ICP (voltage) 3.77, IPR 60, ICP pressure 3400.1. I eased off the throttle, stopped the truck, and noted an uncommanded REV-up by a few hundred RPM and back to idle. It was a quick burp. Afterwards ICP pressure and IPR readings went strange and the code 2284 came up. Looking at the graphs over time, RPM, ICP pressure, ICP voltage, and IPR all follow a similar curve---until the REV-up occurred.
The scanner next showed that as I mildly accelerated to 1705 RPM (about 15mph) graphs showed ICP voltage, ICP pressure, and IPR went up. But when I let off the throttle ICP pressure became fixed at 869.9. I continued to drive the truck.
The truck accelerated fine as it had under previous runs. The Scanner shows that although ICP pressure remains fixed, the ICP voltage climbs and falls with RPM. With RPM ranging from 630 to 1800, IPR holds at about 30. Then under a very heavy acceleration to 44mph, ICP pressure began to increase above 869.9, then followed ICP voltage upwards. ICP pressure climbed to 3479psi with an ICP voltage of 4.64. At that moment IPR read 69%. That seemed normal until I let off the throttle. Then ICP pressure drops back to exactly 869.9 which I assume is some sort of PCM-induced value.
It is during this time at higher RPMs I can hear the engine-cut-outs, but they are mild and the engine still responds to heavy acceleration. I have accelerated full throttle to 100mph and saw max boost values of 29psi (stock program). On engine shut-down and restart the problem seems to reset itself and the truck will run normally for a bit before the failure occurs.
To correct the problem I have removed the banks equipment. There was no change. I have ordered the ICP short connector that will allow me to test actual voltage on the ICP while the engine is running. I plan to soldier some wires and run the meter into the cab for testing.
The scanner reads a desired ICP pressure as well as the actual ICP pressure. When the failure occurs both the desired and actual read 869.9 at less than heavy acceleration.
The scanner also reads desired RPM as well as actual RPM. Desired RPM remains pegged at 640rpm all the time.
Also, engine running the FICM voltage in is 13.5 and voltage out was 47.5.
On the very last test run I got two new codes: P2138 and P2140. I had run the truck with my foot on the floor on that test. Is this a glitch or does this play into my problem?
So I was have a problem the other day with code p2285 did some more checking and found an hpo system leak. Bad injector o ring. I have fixed that. But now when I got it all put back together and went to start it up now have no crank at all, the wrench light is coming on, when I hook up my scangauge it will not connect (so I can't get any readings or codes) I have checked all the fuses that have to do the the ignition system.
They all seem fine. I can get it to crank if I jump the starter wire to the battery. I really need to get this figured out my mini Cooper is waiting for a new clutch to get here and with my truck down I can't get to my job sites next week. I don't know of its just a coincidence or not but while trying to get he truck to start my batteries got drained so got them charged and one was bad (it's less then a year old).
So my 04 f350 was running fine good power and everything till I shut it off a couple days ago and now when it is cold it fires right up but when the truck warms up it just cranks and cranks .... only code I throwing is p2285
Key on engine off
Ipr-14.8
Icp-0
Ficm main power-47.8
Ficm logistics power-14.5
Ficm sync is good
Engine running
Ipr-33.5
Ficm main power-48.0
Ficm logistics-12.5
Icp-875
I thought I fixed it before but I was sadly mistaken replaced the ICP and IPR...
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 RepliesSo the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 Repliesi have a 2007 f350 6.0 and it was running fine. I parked it in my driveway for a couple of months and then went down one day to start it. The first day it started but the second day i went down it wouldn't start. it would crank but wouldn't fire up. I changed the oil, repaired the FICM and still got nothing. Then i took a generic scanner and got the code p2285. I replace the ICP but still no start. I have also changed both batteries. I'm not getting any codes right now either. What is going on?It has around 229,000 miles
View 11 RepliesTruck has performed flawlessly during that time period. Early build 2003 CC SB 4wd King Ranch truck 94,000 miles I purchased new in 2003. Good batteries. Bone stock except for superchips tune.
First sign of trouble: Two weeks ago CEL came on, P2285 Injector Control Pressure Circuit Low, as soon as truck was started after sitting unused for about a month. Bought new sensor, haven't installed it yet (early model sensor located under turbo on rear of engine and a real pain to change). Truck still started fine and ran fine. Dreading the ICP sensor install, I continued to drive the truck. Drove truck 5 miles to get tractor fuel. Got fuel, started truck and drove away. Got 200ft and truck died. I changed secondary filter under hood, turned key on and let pump cycle about 4 times. Truck started. Cleared codes. No longer have CEL. Drove 5 miles home, shut truck off and no start.
Troubleshooting: Changed primary filter under truck. Really cruddy (probably 80,000 mi on it). I cleaned inside filter housing thoroughly. I had to cycle pump KOEO about 6 times before it started. Shut off and immediately tried to start. No start. Ran pump KOEO about 30 seconds. Started. Shut off and same result. I then drove truck 4 miles driving both normal and WOT. No problems, no smoke, no CEL, ran perfectly normal. Shut off, no start until cycling pump KOEO for about 30 seconds. No codes set.
I then removed cap from secondary filter and checked for trash. Fuel and bowl were clean. I did notice fuel drained completely from bowl in about 5 minutes. I reinstalled filter and put pressure gauge on housing.
Fuel pressure readings: KOEO 55psi after about 3 seconds. Engine running 55psi. Turn key off and pressure instantly drops to 25psi, then bleeds off to zero over about a 3 minute time period. Does this seem normal?
Questions: Could the clogged fuel filters cause the p2285 code to set? Could the HPOP system have developed a leak and cause these symptoms?
Could an injector leak cause these symptoms and engine still run ok?
Action Plan: Install new ICP sensor. Do bubble test to check for injector compression leak. Install Blue Spring mod. Waiting on parts. Possibly buy scanner which will read HPOP output etc. Any recommendations here?
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
I have a 2005 F550 with a 6.0. Recently I have had issues with a long crank before starting at times but once it started there were no issues driving. Yesterday it started up in the morning, made a few stops then it wouldn't start at all. Cranked strong but no start. Had it towed back, sat for an hour or two now it starts again. Put a gauge on it and all readings are good. Did have a P2285 code which the ICP sensor. I do suspect there could be an issue with the egr cooler as it needs coolant occasionally. Could that have anything to do with the no start? Truck has started fine today. Why start sometimes then not?
View 11 RepliesEngine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 RepliesI have a new to us 08 e350 6,0 that had a little problem with the oil light coming on at idle and deltas of 20-40 degrees. I put a manual gauge on and press seemed ok, bad sending unit. So finally got back to it and just pulled the oil cooler. OMG it came out, hardly any "oil" around it but semi solid sludge 2 inches thick all around it. Looks like an old 302 someone never changed the oil on. The pic is 2 chunks next to a 1/4 snap on ratchet, ya my camera sucks drank too muck coolant. Seen sludge around an oil cooler before ?
View 14 RepliesI am replacing the turbo on my 2005 f350 6.0. I have the passenger side mounting bolt and the rear mounting bolt out, but cannot get the driver side bolt to budge. I have sprayed it with WD40 and PB Blaster and tried a breaker bar. No luck breaking it loose. I am afraid I might round off the head even though I am using a 6 point socket.
View 12 RepliesI have 2003 f250 6.0, had the turbo rebuilt and I put it back in, my turbo is whistling but I'm also getting a humming noise kinda sounds like a when u down shift at high rpm's idk what's going on, I try and power break as well to build up boost and the tires do not even spin...
View 4 RepliesSo I just purchased my first diesel a couple weeks ago (2003 f250 Lariat). I love it! However, I'm having concerns about my turbo whistle on it. At idle and while in higher RPMs is sounds ridiculously loud (even at 0 PSI in the boost). I've been doing my research on it and I know the 03's have the loudest sounding turbos because they have less vanes than the later models. I know without a video it's going to be hard to diagnose, but I am wondering if a loose boot would cause a turbo whining sound through the exhaust? I have yet to hear ANY other diesel in person that has a turbo whine as loud as mine.
View 14 RepliesFor a while now, I have been hearing a very high pitch whistle noise from the turbo/exhaust area. Everybody told me it was an exhaust leak, but I never could pin point the leak. While I was under the truck last weekend I found the flex joint on the passenger side up pipe was broken a leaking.
I ordered a Dorman replacement pipe that comes with a new gasket and hardware.
I will be the first to admit, I am not a fan of Dorman parts... BUT, this pipe is really nice. It looks identical to the pipe being sold on Dieselsite.com, it doesn't have the scoop inside to direct exhaust gas to the EGR cooler and it comes with all the mounting hardware.
[URL] ....
Once I got the turbo down pipe out of the way and soaked the bolts with penetrating oil, I had the broken up pipe off in 30 minutes.
For a month or two now my truck has been making a squeal and the turbo has been sticking after hard acceleration. The sticking was a woebegone unison ring and I was hoping the squeal would be resolved when I cleaned the turbo but it didn't, in fact, it got worse.
It used to be occasionally and go away after warming up, but now it's more constant than not. It goes away when the VGT does its idle cycle and once you get up to speed.
Here's the sound - YouTube.....
After replacing the HPOP a month or so ago, the bellows decided to let lose on the y-pipe. Which started my Turbo hunting and a P132b code.
This past week my 15 yr old and I replaced the up pipes with a BD Diesel kit. Which after my son redid his part of the job 4 times, we had it licked and running awesome with no codes and zero turbo hunting.
Fast forward to Sunday night coming home from my sisters 30 miles away. I jump on it to pass a slow moving vehicle or 3 and BOOOM! Lots of hissing and no boost on the gauge! Yep we didn't tighten that HAC clamp at the turbo enough.
Get the boot and clamp back on and head to the local parts store slowly to borrow a ratchet and socket. All we could muster from the state trooper was a pair of pliers.
Check the codes after we tighten the clamp and had a P132b. Cleared it and drove it home 25 minutes away and no code but the turbo is hunting. 85% down to 14%. So I reload the stock tune, double check all the clamps on the up pipe kit and pull the battery cables and turn the headlight switch to on. I go inside for an hour or so and go back out and hook up the cables.
I check the codes and the usual P603 is there. I clear it, start the truck let it run 10 mins and then take it for a ride. Pull up to a stop and the turbo goes into hunt mode! Drive it about a half hour and stop. Check codes and find the normal RGR code since I am deleted and the recurring P132b. I clear those and drive back home 35 minutes. I check the codes and nothing not even the P132B but the damn turbo is hunting again!
I check the wiring, and turbo connections and nothing! No leaks, errors or drips. I reload my custom tune and drive it. It hunts less but is still hunting! I am at a lose here! I had it running fine for 2 days. No issues until that clamp let the boot slip!