Golf V R32 :: Steel Rattle Right At The Shift / Exhaust Loose?
Jun 2, 2009
Everytime I run my revs past 4 and shift, I can hear a steel rattle right at the shift. It's stock exhaust btw, no mods...
View 24 Replies
Jun 2, 2009
Advertisement
Ford 7.3L Power Stroke (1999-2003) :: Rattle From Inside Exhaust Like Something Is Loose Inside The Pipe
I recently upgraded my exhaust from stock to a 4" Magna Flow Turbo back kit. After the upgrade, I noticed a strange rattle coming from the tail pipe. It sounded like the pipe was vibrating on something but I checked and it is free from anything touching it. There are no strange noises coming from the engine area. it is only herd at the end of the pipe. If I start the truck it makes a the loose rattle noise like something is loose inside the pipe like the sound you get when you have a bad muffler. About after 4 or 5 minutes I hear the exhaust noise change pitch and make a whooshing noise like a gate or something opening or closing and changing the exhaust flow. After a while it goes away and make the loose rattle returns. The truck has lots of power and preforms great. Where to look?
View 3 RepliesLexus SC430 :: 2002 Hard Steel On Steel Knock Sounds In Front
I have had my struts replaced at local gas station. Unfortunately, there is now an occasional hard steel on steel knock in the front. Very weird indeed.
Is there something they may have missed when they installed them?
Golf VI R :: Brake Rattle Clip Might Be Wiggling Itself Loose
I replaced my front brakes today and not sure if I got the rattle clip back on right as it seems loose. After driving for a little bit, it seems the clip might be wiggling it self loose.
In addition to this, my brakes sounds terrible. Lots of squeals.
I have replaced many brakes and never ran into this issue before. I cleaned everything up and greased the contact points with brake grease. I then did the bed in process that Hawk recommends for their pads.
Golf V R32 :: O2 Sensor Behind The Left Cat Coming Loose And Causing Rattle
Ive been having problems with my o2 sensor behind the left cat coming loose and causing a horrible rattle. Ive tightened the hell out of it a few times and it lasted around 4k miles each. recently i tightened it again and it comes loose within like 20 miles. I was gonna put lock tight on it but with the wiring going into the sensor i cant back it all the way out. I just said screw it and put some JB weld metal putty on it to hold and it lasted like 2 days and now its rattling again. I guess next step is find out how to take apart the sensor so i can un thread and lock tight it....electrical stuff scares me though.
View 3 RepliesGolf/GTI VI :: Loose Manual Shift Knob / Lateral Rotation?
I have a 2014 GTI 6MT, and am trying to figure out if, when I got the car 3 months ago new, the shift knob was loose, or tight. Right now, I just noticed it has the lateral rotation (left/right) maybe 1/8" or so. Just can't remember when I got it, if I noticed that.
Shift knob had lateral rotation when you got your car, or shortly thereafter?
Golf V R32 :: Exhaust Rattle Only When Driving
I just got my R last Monday and have noticed a weird rattle coming from the exhaust. It only happens when I am driving. I can rev the engine when parked and the car sounds great. The rattle seems to happen when the car shifts and seems to happen less often if I've been driving for a little while. I did take it to VW they put it on a lift and checked everything underneath. I was told it might just go away but if not to come back and they will further check it out. What it might be?
View 24 RepliesGolf V R32 :: Exhaust Leak - DSG Rattle?
I did some searching and found someone with the same dsg rattle chatter noise I am getting from my R (check link below)
My R has 102,000 miles, runs excellent but the dsg makes a noise mostly when I am in gear stopped with my foot on the brake. While I was under the car checking out the chatter noise I noticed a faint exhaust leak somewhere in the headers near the flex pipe. I want to fix it and I plan to put on a cat back exhaust very soon but I really don't want to spend the money on a set of headers.
Golf V R32 :: Stock Exhaust Would Rattle When Shifted Up With DSG
OK, my stock exhaust would rattle when I shifted UP with the DSG, seems to be a fairly common thing. I got the EJ exhaust and it STILL does it on occasion, not as bad. Is there a loose heat shield or something? If I rev the car slowly while driving (not standing still) and get it to red line there is no metallic rattle. If I rev it fast and shift, it rattles
View 8 RepliesGolf IV / Jetta IV :: Exhaust Rattle On A Rear Beam
Ever since I got my 3" TB installed I've noticed it rattles on the rear beam. I have tried wrapping the beam with exhaust wrap but it lasts for few days. What could I do to fix it?
View 11 RepliesGolf IV / Jetta IV :: Exhaust Started A Constant Rattle
So I recently lower my car and my 3" exhaust started a constant rattle when I'm in the car. When I get out it stops. Been lowered for a week or so now and today was the first time that happened. I've read up and seen its pretty common when we go lower. Also some ways to possibly fix it.
View 16 RepliesGolf V R32 :: Buzzing Noise From Exhaust When Shift In Higher RPM
How to get rid of that stupid buzzing noise from the exhaust every time it shifts in higher RPM, It freaking sounds like a Honda and it is driving my crazy. I did the Exhaust flap mod but it didn't go away.
View 24 RepliesGolf IV / Jetta IV :: Exhaust Heat Shield - Slight Creaking Noise That Sounds Similar To The Rattle
I've noticed that potentially my heat shield or whatever guard that is 1 step toward the front of the car from where the inlet pipe connects to the exhaust system may be the reason for my rattle at 2k and 3k rpms. i think its a heat shield but I am not sure. the thing is it seems properly mounted, nothing is cracked/broken/or loose. But when I do try and wiggle it it does make a slight creaking noise that sounds similar to the rattle I get. So I could foresee this as being my issue.
But, is there anyway to fix this rattle w/out just taking off the part? i figure its there for a reason and it looks like its held on in 2 places. But they're not nuts they almost look like spot welds or something. 1 on each side. What to do?
Something to get you all in here:
Golf/GTI VI :: Installing Superior Stainless Steel Exhausts?
Got two of these for my Sportswagen. However it seems impossible to screw down all 3 latches to fit the exhaust, I ended up just screwing in one (the one at the bottom)... how to install?
View 6 RepliesPassat (B7) :: Engine Rattle / Mount Bolts Loose
Finally took the Wolf in to see about an engine rattle thats been getting worse. The culprit - loose engine mount bolts! Dealer decided to order new bolts, not just tighten the old ones. Also mentioned a recall for the transmission software. Odd that the "recall" wasn't listed on-line for my VIN. It must be the one that smooths the tranny a bit, it is a bit jumpy at low speed.
View 2 RepliesPrius (2004-09) :: Rattle Noise Like Some Part Is Loose
I have a 07 prius with 60k Km. right now, everytime i go thru a hole, there is always a noise like something is loose. It also sounds like a rattles too. The noise seems to came from the front driver side tire (i have the right side driver japan version prius ). I assume it was the shocks / struts that needs replacement.
View 1 RepliesPrius (Gen 4) :: 2016 With Rattle From Left Rear - Loose Shock?
My wife drove her new (2000 miles) Prius 4 home (300 miles) with a rattle from the left rear. Dealers were totally unresponsive - either put me on voice mail or said I had to wait a week for an appointment. The third dealer I called said I could bring it in and they might take a look at it. Five days later I have a new shock and a bill for the rental car. Not what I expected from Toyota! I noted that one other person on Priuschat had a problem with a loose rear shock.
View 12 RepliesAvalon 2005-12 :: Slight Rattle - Loose Right Front Caliper Bolt
My 2012 Avalon developed a slight rattle at 9000 miles that continued to get worse. I took off the right front wheel today and found the top caliper bolt partially loosened. I could turn it with my FINGERS! The other one was tight as were the ones on the left side.
To diagnose this rattle, find a bumpy road that makes it rattle. Put your foot lightly on the brake (to load the caliper). If the noise goes away, it is probably a loose caliper bolt.
Camry :: 2005 - Loose Rattle Sound Coming From Front Right Strut
Just changed out the struts on my ACV36R Camry Altise. Fitted up some nice Monroe GT struts and Kings Springs (front and rear) as well as new Nolathane bushes throughout.
Now, everything is tight, checked over every nut and bolt with a torque wrench to the correct specs but I have a loose rattle sound coming from the front right strut. What it could be before I tear the whole lot out again? I've been around it with a rubber mallet trying to isolate the rattle but I can't replicate it by hitting any of the components that I've replaced.
Lexus GX 2004-09 :: Loose Heat Shield Like Rattle When Hitting Bumps
Hearing a loose heat shield like rattle when hitting bumps...checked everything underneath , can't find anything loose..? 09 GX-470 56K miles
View 11 RepliesPrius (2004-09) :: Rear Spoiler Loose / Rattle Whenever Hatch Was Closed
The rear spoiler on my 2005 has always had a bit of "flex" to it and I've always been careful not to use it to open or close the hatch. Unfortunately, I can't be sure that others not do that as it really is the place someone would think to grab to close the hatch.
Anyway, the other day I noticed that the spoiler had picked up a nasty rattle whenever the hatch was closed. Looking from the outside in I saw that there appeared to be two plastic fasteners (one on each end) that held the spoiler in place. If I pressed down on one side the other side popped up and vice versa. I was able to get the spoiler back to where it originally was (loose but no real rattle).
The car has never been in an accident and the spoiler doesn't appear to be bent in anyway...it just seems as if the fasteners aren't holding it down as tightly as they should. Is this the norm? Should I replace the fasteners and any instructions on how to do it?