Grand AM :: 2000 V6 SE - Rough Idle And Stalls / Gears Not Shifting When Car In Motion
May 12, 2014
My grand am has a gnarly idle issue. It stalls to turn on and once on it has a very rough idle. When I put the car into drive it stales then just turns off. Drained the heck out of my battery so I was thinking it was an alternator issue but I did a quick test and my alternator seems to be working fine. I did manage to drive my car but once in motion, gears wouldn't shift which has me leading to thinking it can be a transmission issue.
Specs:
2000 grand am
3.4L V6 SE model
automatic
View 1 Replies
Advertisement
I have a 2000 pontiac grand am with a 2.4 L engine it is automatic transmission. Th issue is i just bought the car from a lot thinking it was an easy fix. What happens is when i start the car it goes from a 1k idle to a 500 or lower and sounds like it might die or if i am at a stop light and decelerate too fast it also feels like its going to die and has a few times unless i keep the gas pedal pressed down. I read the codes at my local store they said it was a engine misfire, o2 sensor the front one, and the map sensor.
My farther works at a pull and save which is a lot to pull used parts from cars hes brought a used ignition coil, used boots , i bought new spark plugs and nothing was fixed there. we have replaced the maf sensor and the map sensor both with used parts neither fixed the problem. I am at my wits end here i cannot afford to take it to the shops around here and am trying to get this fixed to get back and forth to work. I may have left out parts that have been replaced, also as far as lights are concerned the check engine soon light is on .
View 12 Replies
I have a 97 4runner Automatic that as your driving it hesitates between shifting its gears. Most prominently happens around 80km/hr shifting between gears.
Its a sort of soft sputtering/jerking motion momentarily. It does shift into the gear and does drive fine once its in the gear. My check engine light is on as well now....
View 5 Replies
Here's what is going on with my 2000 Dakota V6 3.9L V6:
After sitting for at least a couple of hours, the truck will crank but not start. After 3-5 tries, the truck does start but idles roughly at a very low RPM for 10 seconds or so and then stalls. I turn the key one more time and it starts up great and idles and drives normally. This behavior is very consistent. I have only driven it about 5 miles after it started doing this, because on that trip, the engine stalled while I was driving. Occasionally the MIL comes on and gives P0443 as the code. Question is, can the evap purge solenoid cause this behavior if it is going bad? I have inspected the vacuum lines, and they seem ok.
One more note: When this first started, I was pretty sure it was the fuel pump. Replacing that has not fixed the problem, and the fuel pump relay is good.
View 1 Replies
I have a 2003 santa fe I just replaced the cat. in it because it was running so poorly. Now that I've replaced the cat it seems to be worse. The car idles real rough, and cant get it to go over 2000 rpms. No engine light. Had the codes checked and all came out fine. I pulled out the plugs and replaced with new. The car in park ran great until I put it in gear then went back to the same no power, rough idle and cant get more than 2000rpm with out a stall. Stalls but dose not die. Disconnected the pre o2 sensor no change.
View 2 Replies
I have a 2007 camry se v6 and I am having a couple problems.
first problem is when i accelerate and hit about 40mph the car kinda stalls when shifting gears, it feels like a .5 second lag. like its trying to catch the next gear.
second problem, my tire pressure sensor is blinking, i've been told it is because one of my sensors is not working, but i don't know how to diagnose which one it is.
View 5 Replies
1996 Jeep Grand Cherokee 4L
Problem "Stalls at idle and at hwy speed" sometimes starts right up and sometime will not start. Sometimes it will lose acceleration but engine will still be running and you can punch the gas and it will go again.
It has been in the shop for most of the last 2 months. Driven in 3 times and hauled in twice.
Low mileage 70,000 - has been great until now - serviced regularly.
Did get new fuel pump only about 10,000 miles ago do to starting problem but in that case it just did not start.
Independent shop replaced distributor cap, rotor, coil, fuel filter. No codes and couldn't duplicate problem.
Jeep dealer replaced fuel pump (they said wiring problem), O2 sensor, engine module no help, they asked us to pick up car because it ran fine. It stalled within 2 miles of shop.
We replaced gas cap just in case.
Limped back to shop to replace crank sensor as it was suggested several places. Ran fine for about 45 minutes then back to old tricks. Relays have been checked. Still at shop trying to trace problem. At least nobody is saying they can't duplicate problem as it now stalls all the time.
View 14 Replies
Today I went and test drove a used 2006 Dodge Stratus SXT from a private party. Everything about the car was great except it had a bit of a rough idle; there was a slight sputtering noise when not in motion, and the car itself vibrated very slightly. It didn't bother me too much while I was driving because it accelerated and shifted fine and the engine sounded very strong, otherwise.
When the test drive was over I pointed out the noise to the owner, and he admitted that he had mis-timed the timing belt slightly which was causing the sputtering (he is a mechanic and replaced it himself). I was worried about this, but I did some research when I got home and learned that this model of Stratus has a non-interference engine.
My question is this: should that timing belt be a deal breaker for me? Will this cause major mechanical issues down the road? I know it will reduce power but I only really need the car to commute, so I don't mind if I'm not toe-to-toe with a Challenger. I'm just worried it will eventually cause a costly problem.
View 19 Replies
My car is a 2002 Hyundai Elantra with an automatic transmission. It was bought with about 79k miles on it and currently has about 94k miles. Last week I began experiencing rough shifting between gears. My CEL had been on for a few months but I wasn't having any performance problems so I ignored it. When I started having shifting problems I went to autozone to have the codes scanned. All that came up was P0441. I cleaned the purge valve and cleared the code. The CEL stayed off.
I continued driving and having shifting problems. The car slipped out of gear when it wanted to upshift. The engine revs until I release the gas. Once the rpms drop low enough the next gear would engage. This seemed to happen for every gear shift except 1-2. For my first few trips no CEL.
Finally, yesterday on my way to work I got a CEL, and it was intermittent, similar to other issues I had read about. However, the more I drove the car, the worse this problem got. It would not stay in gear while cruising down the road. I tried changing gears manually, revving the engine up and letting it drop to idle, but nothing would work. Luckily the car got me to work but it was a real jerky ride. Towards the end it didn't even want to take off from a stop. And it wasn't in third, the engine just wasn't engaging the transmission. It's like the car was in neutral. But moving the gear shifter didn't seem to work.
The car did not make it home, however. When I started it after work, it went fine for about 2 blocks and then started slipping. Within a quarter mile I couldn't even go in first. Turning off the car and waiting a few minutes, then going again would gain me some distance, but the car would start slipping again almost right away. I was able to turn around and park the car in my work's parking lot.
The problem is I have no way to pull the DTC's now because the car can't make it very far. If it's something simple like the input/output speed sensors, I'll replace those in the parking lot. I'm a DIYer and hate paying others for what I can do myself, but I may need to bite the bullet on this one.
View 4 Replies
2011 Elantra Limited, auto, 15,700 miles. Past couple of days I have experienced very rough shifts in all gears. First noticed on Saturday. Drove about 10 miles Saturday morning, then parked until around 4pm. Car started normally but rough shifts for first 5 miles.
It felt like the car would drop out of gear when shifting, then go back into the correct gear. There was definitely a "pause" before it went into gear, like bouncing up a set of stairs. Problem resolved itself and did not reoccur until this afternoon. Car was parked for 1-2 hours. Same rough shifting for 3-4 miles.
View 15 Replies
Every so often while driving in the city my car starts shifting rough between 1st-2en and 2en-3rd gears. If I stop; turn off the engine and then restart it stops. The car has 107,000 mi. and the fluid has always been changed as recomended. Do I have a shift selonoid going out somewhere?
View 2 Replies
So I have a 2001 VW Jetta Wolfsburg Edition, love the car. So here's my problem, whenever I am driving for more then 20-30 minutes my shifting between gears begins to become more and more rough, like whenever I shift from 2nd to 3rd, it directs me to first gear instead of 3rd and I have to kinda force it into 3rd. This only happens when I am driving for a long period of time, why this is happening? and sometimes when I put it in reverse I get a loud crunch noise but I get it into gear...
View 1 Replies
I just bought the car a week ago 90% of the time it shifts great sometimes shifting very rough and going through the gears way too fast....sometimes its jerky on the interstate as if odd kicking in and out today i jump in cold takes off great get 1.5 miles out and starts slipping the further the more it slips if you let it cool it does just fine again until 1 mile or so and repeats...
Took to auto zone and read fault codes...p0440 evap (expected that one due to its age and mileage 186000)...p0742... stuck on(paper says) tcc commanded off by the ecm-tcc slip detected after off command...p1860..pwm solenoid electrical fault(paper says).. The ecm has detected an improper voltage level on the tcc pwm solenoid circuit...
Fluid level correct and not burnt up although slightly dirty... I have added sea foam to the fluid and what the heck does pwm stand for?
View 3 Replies
Well something I never thought would happen with only 14,313 babied miles on my 2013 silver Elantra. I was driving home from my mothers house and I thought I hit a pothole, next I stopped at a stop sign took off and it started shifting very rough through most of the gears. I drove it around for 30 minutes and it was pretty bad. I decided to get it towed, I don't feel like breaking down in it.
View 12 Replies
I just bought a 1997 Saturn SL2 5 speed it runs great but when shifting gears the RPM stays high while changing the gears. The man who sold it to us said it's done this ever since he's had it (2yrs) and it also burns oil in between the oil changes. I've been told so much I'm torn what to try and do to fix's the RPM to not stay so high while changing the gears.
View 7 Replies
I have a 3.1 that has a rough idle motor runs fine when you get it above an idle no codes show up.
View 2 Replies
2001 Grand am 2.4. Runs fine when the engine is cold but when it warms up the idle is rough. When throttle is added from idle, RPM's drop, it hesitates, then either stalls or goes. Car runs just fine when there is a load on the engine (highway speeds). Sometimes it will even stall coming onto off ramps off the freeway. It intermittently shifts hard. SES light is on p0108. Have replaced the MAP sensor and checked for vacuum leaks, still have the light and the same problems.
View 7 Replies
From the other users it seems that almost all are having slipping of gears and rough shifting associated with this code. On mine I'm not getting any slipping or rough shifting...it actually still seems to be driving just fine. The OD light came on and will go away after shutting the truck off and back on...it will then not flash anymore for say a couple of months or so...this has been happening for the past few years every now and again and i never thought much of it. I just made a 2k mile trip and this happened again but this time it threw the p0775 code which is a first.. Is it possibly a very early sign of the sensors going bad.
View 3 Replies
So I have a 2002 Kia Spectra. I know the IAC has needed replaced for a while but It hasn't really been a n issue at all until today.
So last night my car's transmission started to kick when shifting gears. Mostly between first and second but at other gears sometimes as well. This morning it was still kicking and I figured my transmission was going out.
However when stopped at a stop light I noticed that my car was idling rough. So I turned it off and tried to turn it back on and it wouldn't start. At least not for about 10-15 minutes. So I was wondering if the IAC could be causing the transmission to shift rough at all?
View 2 Replies
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 Replies
My 2000 Hyundai Accent, and it has started shifting gears when not traveling at the right speeds to do so.
I'll try to describe it the best I can, When driving I will be going whatever speed limit and all of the sudden it will make a winding noise (like when jumping on highway and pressing hard on gas peddle) and the RPMs will stall. It is like when shifting up, the car drives as normal but then it will shift down and pulls back (making a winding sound)
I am not sure what to do, I was told it seems like it may be the transmission is shot(I had the fluid flushed previously) and that it could cost over $1000 to get it replaced.
View 7 Replies
