Honda - Passport :: 1999 - Procedure For Removal Of Intake Manifold
May 14, 2011
I'd like to know the number of bolts and locations for removing intake manifold for 1999 Honda Passport.
View 4 Replies
May 14, 2011
Advertisement
Honda - Accord :: 1999 V6 Intake Manifold Carbon Deposits
My 1999 Accord with V6 and 240,000 miles pings on all gas except premium.I removed the upper intake manifold and found a very small pool of oil in the mainifold floor next to the opening that the throttle body bolts to.Also there is a small port in the upper manifold next to the throttle body opening that is about 80% clogged with a hard black deposit. This deposit is also in the corresponding port on the lower intake manifold.I had a new EGR valve and decarbonization done at about 175,000 miles.
The car runs great on premium gas but it is supposed to run on regular which is a lot cheaper.
Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?
I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 RepliesFord Ranger / B-Series :: 2001 4.0 SOHV Upper Intake Manifold Removal
It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?
View 14 RepliesRodeo :: 1999 Honda Passport Door Latches Non-functional
My son has been offered a '99 Honda Passport by his Grandmother. All four outside door latches are non-functional.
View 1 RepliesFord - Expedition :: 1999 - Engine Started Losing Coolant / Intake Manifold Gaskets Leaking
I have a 1999 Ford Expedition. A couple of days ago The engine started losing coolant as soon as the engine cooled. I replaced the coolant only to lose it again when the engine cooled. I was told that it is more likely the intake manifold gaskets leaking. It seems they are right. What is the cost to repair if I take it to a mechanic?
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Hole At The Back Of Upper Intake Manifold
1999 F-250 LD 5.4... There is a hole on the back of the upper intake manifold, just below the back of the throttle body, is a vacuum hose supposed to be attached here? Have a serious vacuum leak, no coolant loss, no overheating, just had cop's and spark plugs done, now she backfires, stalls and will not stay running, mech. says its an intake gasket but the gasket and lower intake manifold look new.
View 7 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Replace The Intake Manifold Gasket?
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 RepliesFord Super Duty (1999-2016) :: JB Weld For Manifold Stud Removal
I started to do my manifold and am 2 and 2. I got 2 out and two broke on top. So far I haven't been able to do anything w the bottom. I have basically seen 2 ways to get the studs out when they break. The first I'd to drill w an ez out and the 2nd is to weld a nut on. I'm not great w a drill and can't weld. I was wondering if using JB weld might be an option. I have never used the stuff but supposedly it's pretty strong. Is there any risk of welding the nut to the head?
View 12 RepliesHonda - Passport :: Oil Light Came On
My car is over due for an oil change, well my oil light for my car came on. Well when I checked the oil dipstick it showed i needed to add oil, i did this just so i wouldn't lock my motor down trying to get it to the car shop to have the oil changed. Well after adding about 4 quarts of oil to my car it still shows i need to add oil but im below the add level...and my car isn't leaking oil and i know im putting the oil in the right spot so what is wrong with it...
View 18 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Removal - 1 Bolt Stuck?
I managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
Honda - Passport :: 2001 - Rattles When Accelerating
I have a 2001 Honda Passport (similar to the Isuzu Rodeo). When I accelerate, I hear a rattling sound. I've taken it to three different mechanics, each of whom have diagnosed the problem as something different, ranging from $400-$4000 solutions. One even warned me that my car would "explode" on the highway somewhere, and drop out all of its innards. How to decipher what the problem is?
View 17 RepliesRodeo :: 1997 Honda Passport - Whining AC At Idle
I own a 97 honda Passport (270,000 miles). My air con functions okay, the problem is the noise. At idle+air on, the revs drop and an unusually loud whine can be heard. Increase the RPM and it goes away. Friend says it the AC clutch, may not be getting full 12V signal.
View 2 RepliesFord F-150 (2009-2014) :: Front Door Speaker Replacement - Door Panel Removal Procedure
We all know the front door speakers on these are horrible. I am changing them out all the time under warranty for being blown. In doing so I decided it was time for a video on how to remove the door panel without damage to get at the speakers and swap in aftermarket etc.
2009+ Ford F150 Front Door Speaker Replacement- Door Panel Removal Procedure - YouTube ....
Honda - Passport :: 1994 - White Smoke Coming Out Of The Tail Pipe
I've got White smoke coming out of my tail pipe of my 94 Honda Passport and I've checked the oil on it and its not milky like I feared it would be. I had some over heating issues after replacing the water pump and all the timing belts. Ran okay for about 2 days, 30 mile drives those days. Replaced some old hoses but it still overheats. Was told by a friend I could be losing coolant from the old radiator cap, replaced it and now I hear a gurgling outta my reserve coolant whenever I remove the cap; which I've never heard before. I don't know much about cars besides your general oil changes and flat tires.
View 6 RepliesRodeo :: 99 Honda Passport - Check Engine Light Popped On And Off For Awhile And Now Steady
I have a 99 honda passport, runs like a dream. Let me say it also IDLES perfectly.
I usually get about 300 miles to the tank, but now my miliage has dropped significantly. The check engine popped on and off for awhile and now its on steady. The computer reads the error of "Insufficient EGR Flow". My mileage has dropped down to about 240-250.
I've already put a brand new EGR Valve in it. That's the only code the computer reads.
I know my mechanic cleaned out the valve part itself I don't' know if he did anything other then that.
When he put the new valve on the car ran without the check engine light for a day then came back, and if I am not mistaken my gas mileage was back to normal, but since the check engine light has come back on the mileage has dropped back down again.
Honda - Passport :: 2001 - Surging And Dies When Slowing Down To Turn Corner And At Stoplight
car revs real high sometimes, other times just won't idle for long with out dying. getting harder to restart after it dies.have changed fuel sensors, oxygen sensors, throttle sensor,mass /map sensor. Whats going on with my car!
View 4 RepliesTiguan :: CEL Came On - Intake Manifold Sensor
Today I was on my way back home from a weekend trip to see family when the CEL came on. The car was running fine no problems (we had driven 200 miles). Gas mileage was good, good power, no weird noises, engine temp was fine (it was 100 degrees outside). But being how the car has 39k on it and its the most expensive thing I own; I pulled over and had autozone scan it for me. It came up as Intake Manifold Sensor. I have never worked on this car but Im going to at some point, I'll replace it myself if it isn't to hard. I am wondering if it is as simple as replacing the sensor or could there be an underlying issue like a blown intake manifold gasket (like i said the car was running fine though)?
View 6 RepliesMonte Carlo :: Intake Manifold Exploding On GM V6 3.8L
Turned the key on my 2002 MC SS, V6, 3.8L, and the Intake Manifold exploded.
Intake Manifold Exploding on a GM V6, 3.8L? It sounded like a 12ga shotgun. Fortunately no one was looking into the engine compartment at the time as they likely would have been killed given the amount of shrapnel from this explosion. Note that the explosion was powerful enough to blow off the oil cap, which is screwed on with very thick threads.
The vehicle was at my mechanics at time and in his forty years he's not seen an intake manifold explode save for those residing on Top Fuel or Funny Cars.
Golf IV R32 :: Nozzle On Intake Manifold Broke
One of the nozzles on the back of my intake manifold broke off. I don't know how to better explain it. The ones the back of the manifold closest to the firewall there are several hoses that hook to the manifold. The second one from the left broke.
View 7 Replies