Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?
Dec 4, 2015
I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 Replies
Advertisement
It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?
View 14 Replies
'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.
Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.
I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.
Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.
Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?
View 6 Replies
So i was thinking about buying a intake manifold for my truck and porting it and polish it. Would it be worth doing. I've decided that trying to port the heads will take up to much time and money for gaskets. Now the only reason why I am buying another stock one is so i can take my time and do it right.
View 14 Replies
I am mixed up in which fasteners I have to tighten to stop my antifreeze leak. For this, I got some pictures. Do I have to tighten these bolts? Or these? Is this the upper intake intake manifold?
I am just really lost and want to tighten the right bolts and find the torquing specs of the bolts. In the first picture, we can clearly see there is a leak there of what must be antifreeze. The stuff I have been loosing slowly over months.
View 7 Replies
Son has a 1987 ford ranger 2.9 engine 5 speed 4x4 truck. See anti freeze leaking @ the rear of the engine where the intake attaches to the block. How long to re & re the intake, ect. Is it just gaskets or what? Is it a big job?
View 9 Replies
Just bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.
Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.
Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?
View 5 Replies
I have a 94 ranger and all of a sudden it started sputtering, i can hear a vacuum leak behind the intake manifold found what appears to be a pcv valve not hooked up is that the way it's supposed to be?
View 2 Replies
I'd like to know the number of bolts and locations for removing intake manifold for 1999 Honda Passport.
View 4 Replies
Which transmission came with the 1987 Ranger 2.9L?
View 4 Replies
I have an 87 v6 ranger with 5 speed that has been sitting for several years. The truck only has 48000 miles on it. The gas tank has been cleaned out and both fuel pumps have been replaced. The injectors were pulled and cleaned...
It will start up and run for about 5 minutes and then will shut off. It will not start after that until the next day and then does the same thing. It starts up and runs then shuts off and can't get it to start again. Could it be some kind of circuit breaker tripping or maybe the ecm. If it is the ecm how do you test it...
View 1 Replies
I have a friend who drives a 1987 ranger 2.3 4 cyl and is having problems with oil building up in his air cleaner. I thought maybe it was a bad pcv valve or worn out rings. I looked at it and cannot even find a pcv valve on it. it has one hose that runs from the valve cover to the air clean but there' s no valve in it. are the rings shot or what is causing this to happen?
View 6 Replies
Still cant seem to fix this 87 ranger 2.9... NEW fuel reg, fuel press reg, rebuilt computer.cold it will start and run fine.then it will shut down with in 5 to 18 miles then you cant hear the front or rear pumps at all!. Let it sit over night and your off again.. Can't get any codes.. Can a pump over heat and shut both off??
View 14 Replies
so I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
View 3 Replies
1987 ranger 2.9l... My truck had no power while accelerating. We'll I changed fuel pump and filter. And still no power. I bought a computer and it tells me the map sensor is not at normal vaccum levels. The ego sensor is reading always rich. Egr valve not opening. Knock sensor was was going crazy. And computer couldn't raise engine speed above normal idle. Could all this be because of one sensor or should I just change it all.
View 7 Replies
1987, 2.9 ... I got all my wiring repaired and replaced both the intank pump and the high pressure pump, for a few days it would fire right up as soon as you hit the key but it had a miss (the pumps shut off after a second or two with the key on "RUN"). I tore the throttle body off and cleaned all the carbon out of it, when I put the throttle body back on I noticed that the engine to body ground was loose so I ran a new piece of 4ga from the intake manifold bolt to one of the master cylinder bolts.
After I did this I went to start the truck and no go, the fuel pump turns on with the key but then it wont shut back off until you turn the key off. if you try and start the truck it will crank but wont fire, after about a half hour of cycling the key and cranking it will start to put a little bit then a few tries later it will start but sounds rough when it first fires. I thought it may be a stuck injector so I ran some cleaner through the Schrader valve on the rail. Still have nothing, both pumps do run but still don't shut off after a few seconds like they should and now it wont even try to start.
View 12 Replies
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
View 6 Replies
I just bought a 87 Ford Ranger 2.9L v6 4x4. It has a tick to it. It doesn't stop, it doesn't increase with acceleration it stays the same. I sprayed some SeaFoam in it and It improved the performance a lot (More horsepower, better reaction to the pedal.) But it is still knocking. I have never tore apart an engine before or messed with lifters or anything. I'm not completely sure how to fix it. I know knocking is not a good thing either.
View 6 Replies
I have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 Replies
I have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 Replies
My dash light fuse blew. I checked with a meter and I have a short to ground somewhere in the wiring for the lights. Everything else seems to be working fine.
Is there a copy of the wiring diagram somewhere?
I have the big ford shop manual but I't doesn't have any diagrams. (might be missing pages, I got it off Ebay and the index is missing T-Z).
I have the Haynes but it doesn't have the diagram for the dash lights.
View 4 Replies
