2006.5 Kia Optima stuck in park and indicator shows R for Reverse. The car roles as if in neutral. Since the car thinks it is in Reverse, I assume this is why the car will not start even though the shifter itself is in Park.
View 5 RepliesLately I've had some issues with the indicator(the orange needle telling you what gear you're in). Often when I start my car, it would let me shift gears but the indicator would not move. I've never once had a problem shifting into whichever gear I want(knock on wood). Usually when this happened I would bring the gear selector back to park then try shifting it again. This would fix the issue and it would bring the indicator with it, but I knew I had to do something about it eventually.
Last night when I was on my way home, I started my car and shifted into reverse to back out. It didn't move the indicator, and nothing I could do(no back to park then trying again) would work. I eventually decided I'd just count gears to get home, then I'd have it looked at.
At home I decided to do some research as to find out the issue, and I thought I'd found it. I removed the panel under the steering wheel to look at the thumb-adjustment. Many posts I read said it's likely broken and I may need a new one (Or to fix it with zip-ties or glue). When I found it though it had not been broken. The white housing and the black wheel were both working fine, the wire doesn't seem cut. However when I put the parking brake on so I can shift gears and see what it's doing, the gear selector moves but the wire just acquires slack in it. It's still attached and I can't see a break in it anywhere, however it may be broken inside the jacket. I tried turning the black thumb-adjusting wheel both ways and got no success from that. It moved a little once but that was it.
The indicator needs to be replaced?
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 RepliesI have been driving a 2003 Chevrolet cavalier and the automatic shift is stuck and can only shift to neutral and drive since Thursday morning. It wont go up to reverse and parking and down to the other 3 shifts.
This first happened last April but somehow with the right grip or pressure was able to get back to all the other shifts. Since then it happened 2-3 times as I can remember and now could be getting worse.
What can I do about my car it's not shifting, it's stuck in high gear and when I go from park to reverse it makes a loud thump. The check engine light came on and the codes are transmission control module it's a 2006 and only has 30,000 miles on it. It's hard to believe it's the brain so we changed the fluid and cleaned the sylinoids but then when I drove it around the block I put it in reverse it didn't make the loud noise and it shifted fine for a minute before I got around the block and almost home it made a loud banging noise and went back to not shifting again. What the problem could be.
View 5 RepliesReverse lights not coming on, and parking sensor stuck at ' OFF ' , have replaced switch to no avail
Any tips out there ?
2005 6.0 Supercab Lariat diesel Auto 4 wd
Well just as stated above...basically when I put my brakes on, my shifter will refuse to go from Park to Reverse. I have to open the little "Shift lock" cap and manually press that button to be able to go to reverse...or sometimes back from D to P. It just started doing this a week ago.
2006 Sonata
Huge problem. Everything was fine the first couple of times I drove today.
Tonight, when I was getting in the car, it turned on. I tried to change it from Park, but it just stuck and wouldn't move and let me change at all, even down to reverse. It's just stuck in park.
What is wrong with it? What's stuck, and what can I do to get it unstuck? Or else, I'd have to get it towed because it won't budge from park
I am a new Prius III owner and am interested in knowing exactly when the engine is running. While the vehicle is moving it is very difficult to tell. I understand that there is a graphic screen that shows red arrows moving out of the engine, but when using other screens I can't tell if the engine is running. Wiring an LED indicator light that shows when the engine is running? And if so, where what power supplied for the light?
View 13 RepliesI am getting a blinking red indicator on the status screen whenever the power is off (locked or unlocked), with a symbol of a padlock over a car.
View 5 RepliesI bought a replacement bulb, swapped it out. No dice. I swapped over the passenger side low beam and still no dice. At this point I know its not the bulbs. I swapped in the original Driver's side light to the passenger side and it works. So now I have an extra bulb.
But the light is not working when I know the bulbs are good. Is this a fuse problem? It just happened one day while driving home from work the light shows up.
How should I go about fixing this and is it most likely a fuse that has gone out or something far worse?
My engine temp indicator shows overheat to the red line, however when I stop the car I can put my hand on the radiator cap and leave it there. No signs of any leaks anywhere. The top radiator hose on the drivers side is hot. Engine runs fine. Oil on dipstick clean. I can't find anything to back up my temp indication. What else I can look for? 1987 chev caprice classic brougm ls 5.o liter.
View 1 RepliesI have a 2006 f150 fx4 4x4. I drove it home from work yesterday and it ran and drove just fine. I got up this morning to go to work and turn the key but the engine won't fire. I turns over just fine. I turn the key to release the trans to put it in neutral to see if it would start like that and the shifter is stuck. I button in the front will not go in. I tried lifting the rear tires off the ground to see if I could free the trans.
View 4 RepliesI have a 2006 F250 V10 that has this issue most of the time but not all the time. Start her up, foot on brake and the shifter wont move. I use the bypass method to get her moving when this happens. It seems to be doing it more often lately. Also I recently has a cruise control issue. Hit the brake to shut it off and it doesn't stop it! Not sure if the 2 are related. The internet said I need to replace the switch on the master cylinder to fix the cruise control. I got lots of different stories on the park issue.
View 2 RepliesI have a 09' 4cyl automatic engine with 54k.
About 30min ago when when I parked the shifter would not move past neutral into reverse and go into park. I can go from D into neutral or the next slot over for manual shifting. Naturally this causes a problem as you can't take the key out of the ignition if its not in park.
I took a screw driver and popped open the cap for the shift release button and used that to move it into park. Turned car off, back on, etc etc seemed fine. So when I tried moving it into reverse and it wouldn't budge. It instead would make a electronic click or snap coming form the steering column but more back toward the engine. Like more into the dash area but back in it. It would make this noise every time I attempted to move it but it wasn't a continuous sound. Just once with each jerk to the side to move it out of park.
So the car works fine except for this. I used it with the screw driver/shift release to unlock it and it drives fine. Goes into reverse and back in park but if I move it into neutral or drive it will not go back into reverse or park.
I've got a 2006 F250 6.0 5R110W 4wd 220,000 miles It started getting a slight delay going into reverse and tow light flashing last week. all else functioning perfect Got a pending code P0700 and P0741 I stopped at NAPA when I was leaving no reverse checked every thing all was normal no leaks and fluid good color drove perfect in drive I got back to the shop [10 miles] put truck in park it was like its still in drive same with neutral, in reverse it wants to creep forward.
View 1 RepliesI am able to operate my power drivers seat in all position except for reverse. My wife was the last one to drive and the seat is stuck in almost the full forward position. I can move the seat forward but not in reverse.
I've already looked under the seat for blockages along the railing and didn't see anything. I would try to remove the seat, but its positioned too far forward to access where I think the bolts would be. I did notice one unconnected wiring harness coming up from the floor under the seat, but it looks like it doesn't go to anything. Maybe its for models with heated seats or something because I don't have heated seats. My car by the way is a 2009 sonata GLS.
Where is the oil filter located on a 2006 1/2 Kia Optima EX V6?
View 5 RepliesKia Optima LX: I have a 2006.5 kia optima. I am replacing my stock radio. I have hooked up plenty of radios with out trouble in all o my old cars.
I have hooked up this radio to where I am only getting power to turn the radio on with out sound. I do not know what I am doing wrong. I have hooked up all the wiring according to the radio insert.
I have heard something with the stock amp which I have located in the trunk on the rich side wheel well area. I can not see what I need to change or if I need to.
Tranny started acting funny recently...shifting hard into reverse at first, then last night it was like it was stuck in high gear or slipping on the way home. Limped it home and took the following codes:
P0743 TORQUE CONVERTER CIRCUIT ELECTRICAL
P0750 SHIFT SOLENOID A MALFUNCTION
P0755 SHIFT SOLENOID B MALFUNCTION
P0760 SHIFT SOLENOID C MALFUNCTION
P0765 SHIFT SOLENOID D MALFUNCTION
P0962 PRESSURE CONTROL SOLENOID A CONTROL CIRCUIT LOW
P0966 PRESSURE CONTROL SOLENOID B CONTROL CIRCUIT LOW
P0970 PRESSURE CONTROL SOLENOID C CONTROL CIRCTUT LOW
On my '96 ranger with an automatic the reverse lights only come on between park and reverse, but once put into reverse they go out. The gear selector on the dash reads right, when the needle is on"P"it's in park, "R" drops into reverse and so forth. Do I need to adjust the shifter cable on the side of the transmission? If so how do I do this (I kinda need step by step with removal and adjusting, I've already tried and couldn't get it off the bracket). It's starting to drive me nuts, I've searched on the web for hours with no luck. I've even posted on other sites with zero answers.
View 7 Replies