Lexus GX 2004-09 :: Shifting Too Slow - Resistance Moving Into Or Out Of A Gear
Dec 8, 2014
I have had the habit of manually shifting down to slow my 2005 GX since new. Only have 55,000 mi so not really a high mileage or worn out yet.
Now the other day there was a resistance moving into or out of a gear (can't remember which) at a time where I needed to get moving so used some extra oomph to try to complete the change and seemed to have a resistance ..... and then felt what I guess was something plastic break.
Now the selector does not stay in 4th when moved left but springs back to "D". Also feels as if the spring resistance is less. All seems looser.
What am I looking at for repair and what is really amiss? Where is a diagram to see the broken parts and how to access it? ---- Part #?
View 10 Replies
Advertisement
I bought a 2010 Elantra Blue in November. It has 1200 miles on it now, but as early as the 2nd week or so I became aware that there is occasionally resistance shifting into 2nd gear despite the clutch being fully depressed. It can also make a slight "crunching" noise after passing through the neutral position and fully into 2nd (though this sound is distinct from grinding, it's not the same as if you were grinding the gears). I've tried a million times to narrow down the cause (i.e. cold weather, low RPM shifting, high RPM shifting, slow shifting, fast shifting, gentle shifting, strong shifting) but every time I think I got it, and have corrected it, it happens again anyways.
View 13 Replies
After car warms and while driving trans moves to 3rd gear and stays ??
View 2 Replies
1996 Mazda Protege, 133224 miles, mostly city driving, automatic transmission
This weekend the car started bucking, problems shifting into gear, chugging, slight odor of oil, very slow moving. This morning (in my pf's) I ran the Scan OBDII and there were no error messages. I checked fluids and they were fine.
Possible problems? I am at a decision point, get rid of the car (needs tires, front brakes and it burns a bit of oil each month (1-2 cups) or fix it.
View 6 Replies
I have a 2001 Elantra gls which I bought a year ago. It had shifting problems from 2nd to 3rd gear with CEL on. I replaced the input and output speed sensors and connectors and fixed the problem to a point. It was still shifting a little hard even after a fluid change with SP111. I added 2 bottles of Lubeguard red and it has worked immensely almost to the point of no problems....except. At slow speed shifting like going into a store parking lot or on a freeway with stop and go traffic, it will shift hard from 2nd to 3rd (I think) maybe 1st to 2nd not sure. If accelerating at normal speed shifts fine. No cel and the tranny fluid is on the full mark, not overfilled. Would a wheel speed senso cause this or damaged clutch pacs maybe?.
View 4 Replies
I have 142k miles on my 2005 RX330 AWD. This week I can feel the transmission slip/shudder when shifting from 2nd to 3rd gear.
My local transmission guy is pretty reasonable but like most salesmen he's going to say rebuild it the entire transmission in lou of something less invasive.
View 6 Replies
I have a 2007 Passat wagon 4 motion V6 and what the problem is I am getting a rough shift between 3-4 gear sometimes, usually on a slow acceleration. I have had the valve body replaced which worked for a couple of months until the problem returned. I then had the transmission replaced which worked a little but the rough shifting is still present at times. The car still has warranty and not even the dealership knows what to do?
View 12 Replies
Stage 2 clutch with a diesel geek short shifter. I have started noticing shifting from 2nd to 3rd is difficult. Sometimes it will go into 5th when shifting up from 2nd. Not a lot of resistance but it is more than noticeable. How do I resolve this issue? Am I hurting my clutch if I keep driving like this? Nothing is grinding at all in between shifts.
View 2 Replies
I have a 90 Celica GTS thats a 5 speed, and the last month or so when going at slow speeds and turning, it almost sounds like tires rubbing bad on the fenders. But they are clearly not. There is also some resistance too when turning. I've checked the PS fluid and its full and not leaking.
View 2 Replies
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 Replies
Feel resistance going from neutral to 1st sometimes (and 4th to 5th or reverse)?
It doesn't happen all the time, but it doesn't feel very smooth. It feels like something is rubbing against the stick. When I reset to neutral and try it again, its smooth as butter.
View 11 Replies
l got a problem with my 01 hyundia accent I have no gears at all,the gear stick is floppy. I have looked at the linkage from the stick to the gear box it's all ok but as it enters the box it has no resistance. The clutch is about 1year old.
View 2 Replies
Just went to leave my apartment and I get at the first traffic light and put it into neutral. Light turns green and I try to put it into first and it won't let me... In fact I cannot shift into any gear while the car is started. Put the flashers on and I am stumped. There was also more resistance in the clutch pedal as soon as this happened.
I turned the car off and tried wiggling it into any gear. For some reason while the car is off I can put it into any gear. So I had to put the car in first gear and start it and limp it home. I had to rev the engine to about 2,800 - 3,000 RPMS in order to get the car to bite and take off. Shifting into any other gear while driving was a hassle and it felt like there was a lot of resistance.
Just did some quick Vwvortex recon and some people are saying that it is a broken pressure plate? Pressure plate welds itself to the clutch? Or possibly a throwout bearing? Also what Transmission is in a 2003 Passat 1.8T Engine code AWM.
View 2 Replies
I have a 2004 Explorer 4.0L with 190,000 miles. My wife was driving it and the vehicle stopped moving. Sounds like the torque converter whining and will not drive in any gear or 4wd.
View 1 Replies
I have a 2008 F-150. When moving gear selector from park to either reverse or drive, trans has a delay engaging. After engagement, it runs fine, shifts ok, downshifts ok....
View 7 Replies
The afs light on my wifes 05RX has been blinking. After removing the sensor I opened it up and saw that it was shot. I ordered a new one from Autozone and installed it. The light now doesnt blink until I start driving it. When I first start the car the afs light is off and if I turn the headlights on they operate normal (starting high and cycling down). If the car is moving the afs light blinks and when the lights are on they are stuck in the high position. I tried the reset procedure I found online but nothing happens.
View 2 Replies
I have a 2006 GS RWD the transmission started acting weird 4 month ago went to many workshops and no codes were found in the computer and my problem is that when i am moving in the car for more than half an hour and stop the car seems hard and jerking while shifting to 2nd gear and if i put it in tiptronic it go to 5th gear immediately it seems ok when the transmission is cold so what do you think it has got 125000 miles on it and what is the normal temperature for the transmission so i can test it with mini vci...
View 7 Replies
I just purchased a brand new 2016 LX 570 two weeks ago. It is a beautiful car and I love all the new technology but I am concerned about the transmission gear change between 2nd and 3rd. The car hesitates and vibrates when shifting between second and third gear then levels out. It a little slow and scary pulling out in traffic without just punching it. This is my first LX and just found out that the LX transmission went from 6 speed to 8 on the 2016 model. I called the dealership and they said the car is very new and they have not gotten any reports from Lexus about the transmission hesitating. Taking it in next week for service and have it checked out.
View 14 Replies
Bought a 2007 es350 2 months ago and transmission shifted fine during test drives but now seems to hesitate when shifting from 2nd to 3rd gear when not warmed up. Also seems to not engage at low speeds of around 5mph again when cold. Seems to shift normally when warmed up or after the the first couple shifts of the morning. Is it a simple fix or a prelude of something worse to come? Other than that I love the car so far.
View 7 Replies
Since recently buying my 2008 GX470 with 100K miles I have been trying to find what is making a low rumble sound when moving. I have checked everything underneath, tightening up a few things etc. to no avail. However recent experimenting with the shock settings from comfort to sport. It seems that the rumble is less when it is on comfort. So I am thinking the shocks themselves are making some noise.
View 10 Replies
While driving, the phaeton acts as if it doesn't want to shift to next gear...it hesitates 2 or 3 time as if it wants to stall then goes.
I've replaced the pcv valve and got the maf checked(good). What could be going on?
View 11 Replies
