Driving home today I was cruising along hwy about 50mph. I threw the shifter over to the manual mode and noticed immediately that it must put it into a lower gear than I was in when I was in automatic bc the rpm jumped up a little higher. I think it put me in 4th or 5th?? I put it back in auto mode and rpms went back to normal. I'm guessing it's the normal way it operates?
View 4 RepliesI have only driven my car a handful of times, but I noticed the past two times, that it sticks in 5th gear during the time that the oil temperature finally gets above the 1/4 mark until it finally settles.
It doesn't stick before reaching the quarter mark, and as far as I can tell, it doesn't stick in auto mode. This doesn't sound like something that should be normal, but what say you?
Driving in normal mode and the transmission in auto. Once the car gets up to temp, (usually at a stop), move the gear selector to manual mode. If you punch it, I have not issues shifting from 1st to 2nd gear, but sometimes, the up shift paddle will need to be hit multiple times in 2nd before the car will shift to 3rd.
It seems to only happen the first time I go from auto mode to manual mode during a drive cycle. It happens on my car and another car I test drove.
I was driving along today and my dash lit up light a Christmas tree. I got PCS, ABS, Brake and BSM lights and I was locked out of first gear in manual mode. Other than the lights and having to driving in auto mode, the car drove fine. When I got home I inspected the rear suspension and saw that the driver's side speed sensor's rubber shielding where it attaches to control arm was damaged. It was not completely severed, but there was a hole and some exposed copper wiring. I had SPC rear control arms and RSR coilovers installed and the car was lowered about 1.3 inches in rear. I was able to use extra copper wire and electrical tape to temporarily fix the problem. After all the wires where connected and shielded with electrical tape, I got zero lights when I started the car.
I'm not sure how it happened. Maybe the wire was damaged during install or it was pinched due to car being lowered. Whatever the case, make sure the wire is secured in a way to avoid being pinched during suspension travel. I ordered the new wire and will attempt to replace. Looks pretty straight forward except the wire goes into the interior of the car somewhere. I read that I will have to remove rear seats. If so, that should be pretty easy. Is there something I'm missing? Will any of the rear interior need to be removed? How to do this?
I have the 12 Accent GL Auto, I have about 161,000 km, and recently say 3 months I've been hearing/feeling this click click noise come from under the car whenever I am in "manual" mode in 1st gear coming from a stop, now I`m 99% sure its not the brakes releasing because I just replaced both my caliper's in the rear and pads and rotors all the way around, And I know this sound because I've had the problem (twice) were my brakes stick so I'm very familiar with that sound this is something different, I want to say transmission because it only does this in 1st gear manual mode, but i know where the transmission is on this car, and this sound isn't coming from where the transmission is, more like under the firewall ( where the trans would be on a RWD car).
View 3 RepliesGot in the car today and moved the gear selector into the manual shift mode. Usually there is no play forwards or backwards. Today there was about 3/8 of an inch travel forward before the spring tension started. I'm taking the car in tomorrow to have the console latch replaced but was wondering why encountered this anomaly in the shift mechanism?
View 2 RepliesMy 2006 Elantra (54,000 miles) shifts really, really hard when it's not cold and passes through the 35 mph range -- hard enough to make you glad you've got your seatbelt on. I've taken it to my regular mechanic and now it's in an automatic transmission shop.
My mechanic changed the fluid (twice), and took it through a "learning sequence". The fluid didn't look that bad and he reported that there were no codes to work with. He thinks I'm going to have to get a new transmission.
The AT shop has confirmed that there are no codes to work with and that the problem begins at 143 degrees. They tell me that the transmission is shifting into a higher gear without releasing the lower gear. They tried replacing a couple of solenoids, but that yielded no change in behavior. Now, they're telling me they "think" I need a new computer. I'm just afraid the trial & error approach is going to cost me a boat-load.
I have a 2007 Santa Fe 3.3. On occasions in low gear as it goes to change gear it will seem to cut out, check engine light flashes on then off engine revs as I have foot on accelerator but then everything seems to restart and is fine. Seems to buck for that second or so and is when I have just started a journey. doesn't seem to do it at other times during a trip.
View 6 RepliesI have a Hyundai Santa Fe 2007. have recently had problems with the car not want to start in P mode on the automatic gear box.
It starts as usual in the N mode instead.
Looking for recognize the error, what could it be? A sensor, fuse, or what?
Just got a 2012 Lexus RX 350, but find out that the engine sound is quite "noisy" in the lower gear or when pushing the pedal. Is this just my car, or is common?
View 14 RepliesI just bought a 2013 model RX350 about two weeks ago.
I am wondering why does my car default to 4th gear even at a stop when put into Selectable Gear Mode; I would think it should be in '1'. Is this a faulty vehicle requiring some fix?
In other brand vehicles I have driven, shifting into S-mode at standstill puts it in '1'. At highway speeds, it would be '6' and at intermediate speeds it will be some number in between. I can then upshift and downshift from that number as I would change gears in a manual drive car.
Is that kind of "manual simulated" driving feasible or advisable in the RX350 with the default 4th gear behavior? I have not dared to try starting from the '4th gear' for fear of ruining anything.
how to use the steptronic on the RC , it's going to shift by itself or i had to press the shifted pedal to bring up the gear , before i had a BMW so usually it autoshift on DS mode , what about the shifting on the RC.
View 5 RepliesWhy my vue manual tranny only goes in first third and fifth . Can't get it in second fourth or reverse . Bought it like that .
View 1 Replies1997 Saturn SL ... It's like 3rd gear is where 1st used to be and 4th is where 2 used to be. 5th and reverse work but are more towards the center. It's as if the stick shifted over to the left.
Is it possible for the shift stick and it's linkage to become displaced? The temp did drop today about 40 degrees and it snowed but the car stays in the garage and was only parked at my work for a couple hours after a 2 mile uneventful drive.
No warning lights that I can see but the check engine lite has never worked. The engine is a 96 rebuild but the transmission should be a 97 like the rest of the car.
Great mileage and otherwise drives fine.
I have a 2007 es 350 106000 miles. Other day it happened car stopped i took it to my mechanic and he looked at the codes and it indicated key fob prob and something with the trans. Now it happened again. Car wont go into any gear.
Past few months i noticed a stutter at low rpm. i read a lot of people had tourque converter problems when this happens.. My question is i was just gonna change the converter and see if it fixes it but I don't know if the trans is shot to.. it was shifting fine only the shutter at lower rpms....
What speed the car is in 8th gear ? My 08 LS supposedly has 8 speed A/T..
View 7 RepliesMy 1997 Saturn SL2 with 5 speed manual transmission won't shift into first or second gear. When I shift into the location where first would be the car is in third gear. It shifts into 4th, 5th and reverse just fine, though the shifter is in the wrong position for those gears. I can wiggle the shifter in neutral and get it to move into the position where 5th and reverse are normally found, but it is stiff and makes a clunking noise when I move the shifter over to the far right side.
I have removed the center console and the bushing appears to be intact. Both cables are in their proper positions inside the vehicle and at the engine. One of the cables (the top one in the engine) has some wear and tear on the boot, but does not appear to be binding. Other than the stiffness and the clunking noise, the shifter seems to be working fine too.
I am loosing gear oil through an odd place . There appears to have been a rubber boot or cover over this area that got cooked by a hot exhaust (whole other story there). This is left (passenger side) just above where the axle enters the gearbox. Not sure what this is and how I can resolve the issue. I have temporarily used silicone to stop the flow and have topped off the gear oil, but am still leaking a little. I have already done some damage to the bearings I fear, as the tranny really whines when I get up into 4th and 5th.
View 4 RepliesWhat RPMs do you see in 6th gear, say at 60mph or 80mph? Consumer Reports claims the RPM at 60mph is 3020!
So I went to vw.com to look at the gear ratios for a reality check. The site lists two final gear ratios for the manual. "Final I" is 3.94 and "Final II" is 3.09. When do you get one versus the other? With a final gear ration of 3.09, I get roughly 2400RPM at 60mph. But with a ratio of 3.94, I indeed get about 3000RPM at 60mph or 4100RPM at 80mph!!! That's absolutely insane.
1993 Geo Prizm with some odd 275,000 miles on it. Was at a stop sign, in first gear, and gave the car some gas. Very quickly it jumped out of first gear and stopped moving abruptly. Tried to get it back in first gear and it just stayed in neutral. Had to push it to the side of the road. Tried putting it in any gear and it wouldn't go. Then tried to have the car running in neutral and let up on the clutch and as soon as I started letting up on the clutch, something (like metal) started grinding. Pushing the clutch it (in neutral) stops the grinding. So, do I need a new clutch? New transmission?
View 11 RepliesMy 1985 BMW 635, standard transmission suddenly developed shifting problem. It will not shift into 1st, 3rd or 5th gear. It will shift into reverse,2nd and 4th gear. The car is not driven on any frequent schedule, infrequently. I can't remember the last time the transmission oil was changed.There has not been any mechanical distress,grinding of gears,etc. you just cant engage those gears. They all are moving the shifter from neutral to a up position. Is it possible that sludge could be blocking the movement of the synchronize r?
View 2 Replies