After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 RepliesOk, Im trying to get my front licence plate holder off. I've looked in all the DIY forums and cant find what im looking for. My question is how do i get this thing off?? I've took the two screws that hold the thing to the bumper off, and its still soild as before i took the screws out. Is it held on by the rub strip?
View 24 RepliesI have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
What the heck caused this? Something melted through the license plate holder, then through the plastic of the bumper, down to the metal body. A week ago I had the timing belt, plugs and water pump replaced by my mechanic here in Orlando. I didn't notice anything when I picked it up but I didn't really do a visual inspection of the front of the car either since it was parked facing a fence when I picked it up. Since then it has been driven by my wife to work 3 times. While there, she parks against and facing her building with only a row of shrubs in front of her. And at home it's parked in our garage with about a distance of 3 feet from the washing machine. I asked at my repair shop and they said they had no idea what could have caused this other than a diesel truck, however there is no residue typical of a diesel exhaust.
View 19 Repliesyesterday I got the idea to move the plate bracket on the front all the way down so it gives it a much cleaner look and doesn't obstruct the grille. To do so test mount the bracket on the lowest position, then have someone hold it. Then you take a 1/8 drill bit and make the two new wholes then put everything back together.
View 8 RepliesI need to mount a plate on front bumper and there are dimples for 2 holes. Do I just use self tapping screws here as I've read you don't need a mounting frame?
View 3 RepliesI wanted to change my license plate bulbs to LED's. Can't figure out how to get to them. The book says have the dealer replace these bulbs if burnt out. I Always like to try to do things myself.
View 7 RepliesHow to change the license plate light bulb for lexus rx 350 2010.
View 4 Repliesreplacing the entire front bumper.I have removed the front license plate holder, and would like to fill the holes where it was screwed into the front bumper.
View 8 RepliesReplacing license plate bulb on a 3rd gen rx? I tried taking off the interior lining on the rear hatch but no luck. There's access covers for taillight & reverse, but none for license plate light. I also tried "popping" out the plate light cover right above the license plate... don't think they are designed to be popped out.
View 3 Replieshow the chrome trim above the rear license plate is removed?
View 4 RepliesMounting front license plate somewhere other than the "official" mounting location? I don't like the thought of putting holes in my front bumper. I can move it down a bit such that the holes are in the bumper just above the air opening. So, they would be less noticeable. This would block some of the airflow through the lower opening. But, unless I'm driving in 100+ deg temps, it probably won't matter.
I could also offset it to the right or left in the lower opening.
I plan to remove the front license holder from my car, fill the holes, and paint/clear coat/sand them. Any recommendation as to what to fill the holes with (I'm not going to use a plug.) Exactly what the bumper cover is made of, I can find the right material to bond to it.
View 2 Replieshad a couple questions about installing the front license plate. I currently do not have any holes drilled in the front bumper (though I can see the places where they are supposed to go). I have the black plastic attachment. What is the best way to drill those holes? Can it be done if I don't have a drill (i.e., just with a screwdriver and force)? Is this something the dealer might do for free (I don't have a warranty, bought my car used)?
View 9 RepliesHow do I get rid of license plate holes on my front bumper? I took my front plate off and now I am stuck with annoying holes drilled into my front bumper. Its not noticeable but i know its there so it irritates me.
View 4 RepliesFor a few weeks now I noticed my stock license plate bulbs started to act strange. My left one is about half burned out, and the right one started to flicker and burned out entirely.
So.. Easy fix right? I bought 4-smd led lights to replace the burnt out ones and as soon as I installed them they worked perfectly! But about twenty minutes later .. The right one burned out. And the left one is dim.
Is there something wrong with the wire? what can I do?
How do I change my license plate bulbs in a 2010 ES350? I bought some 194 JDM Astar LEDs. I took off liner and changed backup bulbs but can't figure out how to change license plate bulbs.
View 4 RepliesI'm in the process of replacing license plate bulbs. I broke the old housing for one of the bulbs so I bought new LED lights on eBay and they came with the housing. The problem is, I can't get the cover to stay clipped in to the tailgate. How to get the lights to stay in? What am I doing wrong?
View 7 RepliesI'm trying to change my license plate bulbs to LED but cant figure out how get to the bulb. I've already removed the carpeted cover but cant seem to figure out how to get the bulb out..... 2007 ES350....
View 3 RepliesWhere the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 RepliesI try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 Replies