Just got my 2013 RX 350 CPO and been driving it for 2 weeks without any problem. But today when I was trying to steer my wheel all the way to the left (car was parked) and I heard rubbing noise coming from wheel base. It only happens when making hard left steering not right.
I read online and seems like it's a common problem for wheel bearing for Lexus cars.
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
I just got a 2013 Corolla Saturday (manual transmission). So far, I love the car, but I think I'm having a problem with the steering column. When I turn the steering wheel in a parked position, I can hear an audible "rubbing" noise coming from the column. I called the dealership, and spoke not only to the service department, but also to my salesman, who has one too. He says he's never heard that, and the service department assures me it's normal and is because it's an electric motor now instead of a fluid power steering system.
So, do I have reason to be concerned? Experienced this after only 300 or so miles on a new car? We traded a Scion IQ for this Corolla (didn't like the CVT whine in the IQ), and never heard anything like this.
I bought a 2010 lexus ls460l awd with about 80,00 miles on it and also bought a warranty for 3 year/ 36,000 miles. After having the car for a couple of days i noticed things that I didn't like as well as figured weren't normal, alot of it had to do with noises, the dealer told me they didn't cover noises, and i asked if those noises meant something was wrong then what?? It was mostly squeaks and rattles that I didn't expect to hear in a car of this caliber, going over uneven road there's a constant squeak coming from the front, if its a bump its an extremely hard thump in the rear, and the idle.....is BY FAR the loudest I've ever heard in any car that I've been in.
When I turned the wheel all the way in either direction and pressed the gas, it made a rubbing noise with a harsh vibration, brakes squeak horribly about 2 days out of the week for about an hour then it goes away. When i took it in they said everything was fine except a part on the rear struts and said they needed some special oil for the vibrating rubbing issue. Picked up the car and noticed the vibrating issue was resolved but during the drive home noticed everything else stayed the same.
Basically, when I make a hard left turn I hear a noise out of the front right wheel area. I do not hear anything in any other condition. It sounds like something rubbing up against something else. I know that my rims are in good shape - is this an outer or inner bearing issue? Or is this something completely different?
View 2 RepliesMy friend with an 07 with about 109k miles on it now has started getting a "groaning" noise whenever the wheel is cut hard to the right or left, either sitting still or rolling. A local repair shop (not the dealer) checked it out and said there was some "stuff that needed to be lubricated". Not trusting this opinion he went to a Toyota dealer where he was getting new brake pads installed on all 4 corners (no Lexus dealer in the city where he lives), they diagnosed the car as needing 4 new struts and a new balljoint.
If in fact he does need the struts and balljoint, I am thinking chances are there will be a bunch more suspension stuff that should really be done at the same time when everything is apart anyway - perhaps bushings, endlinks, etc?
Is he better off sticking with the OEM strut replacements or should he go aftermarket? He's not looking to slam the car or anything, and is more of a ride comfort guy than handling enthusiast.
I took my car in the other day for 4 new tires at 8am I drive home 2 miles from the place. I work nights so I sleep all day. As I was going to work at 11pm I noticed it sounded like the front drivers side tire was rubbing up against the car when I turn the wheel from left to right. I took it back to the place I got the tires from. I thought something might be adjusted wrong or something. They call me to tell me that the tires are fine and the problem is that I need a new power steering pump. There was no noise or steering problem previous to me getting the tires.
I took it to pep boys (the only place open last night). They say the pump needs to be replaced along with racks and pinions..etc. I ask if the leak can be slowed or stopped with one of those stop leak products and they say no. The fluid just drains right out. Is there something the guy that put my tires on could have messed up to cause this problem?
I spent a lot for the tires and within 5-10 miles later this problem starts. The car has over 250000 miles on it and I cant justify spending that much money to repair it but at the same time Im in a bind financially (medical bills, divorce) to get another car right now. I realize even if they did mess it up when they put the tires on, they wont admit to it anyway.
Having issues with Gen3 Prius steering column? I suddenly developed this clunking noise when I rock my steering wheel from left to right. It's steering correctly but I've never heard this noise before....
View 7 RepliesMy 04 gli makes a rubbing noise when accelerating thru hard left turns.. but weird enough i can take the same turn at the same speed in neutral and have no noise at all. I changed both front wheel bearings and cant seem to find the answer. I brought it to vw and they checked the whole suspension struts springs cv's tie rods ect. and they all checked out good they said. the car used to have a exhaust and i just recently put it back to stock, could the exhaust make the noise perhaps?
View 1 RepliesSo, I put my RCs with Eagle F1 DSG3s back on and now I have noise. I thought there was some rubbing, so I spaced them out tonight, but the noise is still there. I thought it could be my alignment, so I got an alignment, still noise.
It happens when I'm going straight and when I turn left, but not at all when I turn right, things get quiet. It sounds like a a rubber rubbing noise but i took the wheel off and I couldn't see any wear... Could it just be tire noise??
Over the past few months I'd noticed an intermittent grinding noise coming from my left front wheel at low speeds. I took it in once but it refused to play along so I finally managed to catch it on camera and let the dealership listen to it. They booked me for today, saying it sounded like a wheel bearing (to which I agreed) and I dropped her off around ten, not expecting it to cooperate for the second time.
I got a call from the dealer around 2 PM saying that they were able to duplicate the noise and that when they took the left front wheel off and ran the car on the lift with the rest of the wheels off the ground, the noise went away. Even stranger still, when they put the wheel on the tire balancing machine and spun it, gronch, gronch...gronch, gronch....gronch, gronch. It was coming from inside the wheel! I gave them permission to dismount the tire from the wheel and about ten minutes later I got another call saying they'd found a handful of tiny hard rubber balls inside the mounted wheel/tire assembly that were rolling down the inside of the wheel and causing the grumbling at low speed.
Here's the kicker: they were in all four wheels! The tech even saved them for me so I could take a look and they don't look like anything mass-produced; some are larger than others, some are round and some are oval-shaped but when I dropped one on the glass advisor desk, it made a very clear 'Clink!'.
Experienced a buzzing noise from left rear wheel well. I have noticed it a couple of times after the car has been parked in the garage and sitting for awhile. The dealer said it is normal and the auto suspension readjusting. However, it will continue for a long time but will turn off if I start it up. I am concerned this normal leveling will burn out the motor in do time. We have a 2010 premium.
View 9 RepliesI recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
Took my car in for 10k mile service and let them know there has been some clicking noise coming from the front suspension when making a left/right turn...
I dropped off my car on September 21st and they have yet to complete my car... I've called them every single day since but, I don't get a good explanation from the dealer...
when i am stopped and turn my steering wheel a lot to either left or right, and i accelerate, there is a loud thumping hammering noise coming from the front of the car.
it also happens when i am turned a lot to the left or right, and i reverse. it sounds like a hammer hitting cement. it only happens when i turn almost all the way to the left or right...?
I've got a nasty groan and vibration on the steering wheel coming from my Steering Pump when I turn hard right or left. There seems like a little bit of oil around the pump and some traces of shiny metal (tiny sparkles) near the spline so I'm pretty sure the pump and pulley needs replacing.
View 1 RepliesI have a 2002 Silverado 1500 Z-71. In 4 wheel drive, I can hear a humming/rubbing noise from the front end. Not real loud, but enough to get my attention. It happens at around 25 mph, and just as I'm coming to a stop. This is on the street.....going straight, not while turning. I only engage the 4 HI during street driving on a straight line drive just to "exercise" the gears and transfer case. I don't notice it on the dirt 'cause of trial noise levels. All fluid levels are normal in transfer case and axles. How much noise is normal during 4 wheel drive operations?
View 14 RepliesYou can hear the clunky, groaning noise around 8 and 11 seconds when I turn the steering wheel, making a tight u-turn in an alley way.
What can it be..? I hope it has something to do with my tires since I'm getting new ones today. The current ones are pretty bald.
Quick video clip of noise...
I have noticed recently that I have a "rubbing" noise and vibration coming from the right front wheel on my FX4. It is most noticeable from 5-10 MPH, and more pronounced when turning right. it is not constant. It sounds almost like a brake pad rubbing on a badly warped, wet rotor. It goes away when I apply the brakes. I am thinking bearing or possible CV joint.
The dealer can't get it in until Tuesday, and they say I will have to pay the deductible on the ESP, even if it is related to the steering vibration they could not replicate or fix about a month ago. I am seriously considering going to another dealer for my service. Given, they did absorb the deductible last time, but they didn't fix the problem!
I ask this because when on the hwy (60-70mph) you can feel some vibration in your hands. I can let the steering wheel go and it won't move a bit but when hands placed on it you can definitely feel the road, including bumps, and regardless of road conditions. Tires where balanced at 7500mi but it still happens. Regardless of temperature or PSI in the tire.
I thought we had electric/electronic steering and no hydraulics? Maybe unrelated but, when turning in my driveway, very slow, I can hear a slight clicking (maybe rubbing) noise coming from the steering wheel column. Everything else has to be silent to be able to hear it.
My 2006 AWD RX330 rotors were starting to get warped so I changed them out along with new pads. I put new rotors in the front and new pads all around. Everything went smoothly other than getting the bottom rear slider pins to go back in easily.
Well it's been a week now and I noticed that if I press on the brakes at low speeds say 20-30 mph with a decent amount of pressure nothing too crazy there is a rubbing/pulsing noise right before i stop completely. It doesn't happen right when I apply the brake but right before the stop. It kind of sounds like the ABS is kicking in but i don't feel it in the pedal like you do for ABS or I don't hear the electrical noise you hear from ABS.