Lumina :: 1994 Chevy 3.1 Stalls When Put In Gear While Engine Warm
Oct 18, 2014
A week ago, driving home, the tech started to drop quickly to zero then recover, like the ignition was turned off and then back on. I was able to make it home. The car was due a tune up. I replaced the crank position sensor (OEM), replaced sparkplugs (Autolite Iridium), air filter, fuel filter, no luck. I ohmed the coil packs, secondary resistance showed good, replaced the ignition control module (aftermarket). After this, engine would stall after it was at temp, could restart, once put in gear it would stall, but I could go in reverse and drive home backwards.
Reinstalled original OEM ignition control module. Towed to GM Dealership, mechanic said fuel pump was bad, ignition wires needed replaced, one injector ohmed bad. I took car home, replaced fuel pump (OEM), ignition wires (OEM), no luck. Removed plenum, found pcv valve clogged, and hose kinked, replaced both, ohmed all 6 injectors, 5 injectors read 12.3 ohms, 1 injector was 11.6. Replaced all 6 injectors, (Napa), plenum gasket, still same problem.
GM dealership said computer said no data, they though perhaps ignition control module was bad, but I don't think so. I hooked up my Actron shorting plug, reads code 12 which means no faults, no other codes. I noticed EGR valve has a lot of carbon in the hole, thought about changing it, but I'm really not sure where to go now. The car is a 1994 Chevy Lumina with 230,000 miles, spent about $500 the last week doing brakes, and trying to fix this engine. Where to go from here.
View 5 Replies
Advertisement
My 1994 volvo 240 stalls at idle when the engine is warm. It's happening more frequently as the weather gets colder, I'm not sure if that's a coincidence. The car is an automatic and I'm wondering if it could be something as simple as low transmission fluid.
View 1 Replies
My 1994 Chevy Lumina drives great when its in motion but when it warms up it will stall when your at a stop light. It does great at a quick stop, like a short red light or a stop sign but when I am sitting at a long red light it just stalls. It will start right back up but this is annoying. Recently the car radiator was replaced, so the car over heated. What could the problem be?
View 2 Replies
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 Replies
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies
I own a 95 chevy 1500 with a 5.7 engine. The other day I'm driving home and my truck completely stalls out and has no power what so ever. To be more specific I didn't have lights, radio, key buzz nothing. Well by the time I got the under the hood I had power again and it cranked right up. I put it in drive and 5 minutes down the road and it stalls again with no power what so ever. I've been having problems recently with it stalling at stop signs/red lights but never with a loss of electrical systems. What this could be?
View 3 Replies
I have a 1999 chevy lumina 3.1 with only 317,000 mi. and running strong. I had put new plugs,and wires about 6 weeks ago. The other day it started misfiring and I could smell the gasoline. I checked the tail pipe and it showed black smoke. In addition I put a piece of paper on the tail pipe and I could feel the misfiring with a consistent rhythm. I notice that it is running flooded(like if a fuel injector is not working correctly.) I cleaned the throttle body, checked all the coils and the spark plugs and they are good. It does not show any check engine light on. What could it be?
View 6 Replies
Was called today to look at a car that wont start its a 92 Chevy lumina euro with the 3.1 v6 automatic 4 door. The car has a new crank sensor recently installed ran well for a while and now has no injector pulse. Checked for spark its good. sprayed starting fluid in the intake and it fired for a second acted like it wanted to run and then died. Checked for fuel at Schroeder valve it has fuel there I don't have a fuel pressure gauge but it sprayed pretty good. I'm not real good with electrical but thought maybe the ICM under the coil packs could be bad I have one off a running engine on my shelf but wanted to see what other people had to say first.
View 4 Replies
So about 3 weeks ago, I was driving down the road at about 55 mph, on cruise control, when my car just started slowing down. I looked to see all of my dashboards lights on and I realized my car was not running. I shifted into neutral and the car started right up again, but when I pushed on the gas it just kind of stuttered and shuttered before dying again. When I came to a stop, again the car started right up, but repeated the shuttering and hesitating when I pushed on the gas and tried to get going again.
So, I repeated, but this time i just pushed very gently on the gas, getting up to between 5-10 mph before the car died again. At this point, it just stopped running completely. The engine would turn over, but would not keep running. When I got it into the shop, the mechanic said they put a fuel pressure gauge on there and the readings indicated that there was plenty of pressure, no problems the fuel pump or lines.
After further research, the mechanic said he thought it was an electrical problem, that it could be the crankshaft sensor or the ignition switch module, but he just did not really know for sure. I had him replace the crankshaft sensor, since it was the cheaper part, and it didn't fix the problem. So now I am just kind of stuck on what to do here.
View 4 Replies
This car started to stall sputter. I replaced the ignition module and it worked for while then nothing at all but still cranks. I checked all of the fuses and every thing was working. What I have found and i think this was the whole problem. The wiring harness that goes from the ignition module to the crank sensor, the wires were twisted and frayed and most likely grounding out on the frame and making the computer to shut down. So far after replacing the wires it started right up. Have not had a chance to take it for a test run to re learn the computer because my brake line busted.
View 1 Replies
My brother's 1995 chevy lumina 3.1 engine has been dying while braking for a stop and while reversing. Has replaced fuel filter, map sensor, throttle sensor, o2 sensors and still no change. He says he doesn't believe a tune-up is the cause either.
View 8 Replies
I have a 99 Chevy Lumina. The car periodically flashes the low coolant light. I check it and its fine. I don't know if its related to my recent problem. A couple of days ago, my car wouldn't start. All the lights and stuff come on, but there is no clicking or even trying to start. I kept trying. It wouldn't work. I left it alone to make some phone calls. I messed with it again after a little while and it started. It has been running until today. It started, I got my son to daycare. Then when I tried to start the car to leave, it did the same thing again. I let it sit for a couple of minutes and it started again.
View 13 Replies
Last winter, my car sporadically stopped while I was driving slowly or while I was standing still. I usually turned the engine off and restarted it right away without a problem. It happened a few times and then it stopped. This winter, it began again - frequently. I realize now that it only happens during the cold months.
View 10 Replies
Have a problem with my Santa Fe. 2004 2.4l.
My wife drove the car when the problem first appeared. She had been driving for 30 min, roughly 30km, and the car looses power and stops. Won't start when she tries. It cranks but won't fire up. When she waits for a minute it fires up but stalls.
We took it to a workshop. No code. They changed the fuel filter, which hadn't been changed for a long time.
They took it for a drive and it worked fine. I picked it up and it was working. Then it died when I exited the highway. It had lost some power during a second while still on the highway. I had driven it for roughly 30km and the engine was hot. Again, was able to start it it up for a couple of seconds if I let it cool for a couple of minutes. Got a lift home and returned in the evening and it started on the first try.
Took it to work the next morning. Wouldn't start in the afternoon when it had been standing in the sun and was gazing hot. Opened the fuel cap to release any vacuum. No change. Again started when I returned this morning and it wasn't very hot.
The engine warning lamp hasn't light up. Will try to see if there is a fault code tomorrow. Will try to measure the fuel pressure eventually.
The valve position sensor and timing belt was changed a year ago.
View 8 Replies
1995 Chevy Lumina 3.1L Sedan with ~182K mi
Over the past 6 months, I have noticed fuel odor just about any time I turn off the vehicle, and I am also experiencing progressively higher levels of fuel tank pressure each time I remove the fuel cap. The fuel tank pressure seems to be greater the lower the level of fuel in the tank whenever I remove the cap. 6 months ago (~Sept) it was only a slight "hissing" periodically when removing the cap to fuel up, but now it occurs at every fill up and seems to have enough pressure to push the cap entirely off had I not been careful to slowly loosen the cap to relieve the pressure.
The entire fuel pump and sending unit assembly in addition to the tank and filter were all replaced about 4 years ago in May 2010 or about 28K mi ago. The issue has just come up progressively over the last 6 months.
Today, I inspected the evap. emission components and lines from the tank to the canister to the purge solenoid mounted on the rear of the engine. All lines are connected and seem to be in operable condition. The line from the canister to the purge valve mounted on the engine is completely free with no obstructions. I blew out the line with compressed air and absolutely no exiting particulates were observed. The lines on the bottom of the canister did not show any signs of wet fuel and there were no carbon particles present in the lines from what I could tell from disconnecting and inspecting. The vapor line from the tank to the carbon canister is not kinked or pinched in any manner.
I believe there is a fuel vapor check valve that resides inside the tank connected to the fuel pump assembly/sending unit. This was all replaced as a single unit as mentioned above. I am thinking this check valve may not be functioning properly and not allowing the vapor to escape into the carbon canister. I tried to apply slight pressure and vacuum on the vapor line connected to the check valve on the tank but no air was able to move in or out even with the gas cap off. However, I do have a full tank of gas right now, so I imagine the check valve will be closed.
The check engine light is not on but since this is an OBDI vehicle I am not sure there are any evap. emission codes anyway.
How can I test the gas tank vapor check valve? How can I test the vapor purge solenoid located on the rear of the engine? What malfunctioning component could be causing the excessive fuel tank pressure.
View 9 Replies
1995 Camry 2.2 4cyl 165,000 miles FED (not CA).
Two days ago while doing a routine oil change I noticed my kids engine compartment was real dirty as we had alot of flooding from rain a few weeks ago. I sprayed the engine with a water hose w/nozzle to clean it. At the time I didn't know any better. The car was driven without any issue briefly that day. The following morning the car was driven a distance of 25 miles without incident.
After resting 30 minutes the car was started and began to idle rough and stalled repeatedly. When I showed up to inspect the issue it had been sitting about an hour. I went for a test drive and the car ran good. About 20 minutes later iI get another call saying the car is doing it again. It was sputtering/ hesitating when I attempted to accelerate it began to stall unless I limped it along staying off the gas.
Once I got it home I started doing some research and discovered that my spraying water in the engine compartment was probably what caused the issues I was experiencing. So I began to go through the motions trying to repair. I also noticed the car ran good when cold but at operating temp it would run rough. The check engine light has not come on.
I replaced the spark plugs, plug wires, distributor cap & rotor, etc... sensor, and air filter, I cleaned the throttle body port and IAC valve port with sea foam cleaner. I cleaned and tested the EGR valve & ports. Nothing has improved from my efforts.
I must of screwed something up good, since its been 2 days, it should be dry by now. I also been thinking that maybe some water got to the injectors. NOt sure if a cause, but the oil was changed right before I sprayed engine.
My course of action as of right now is.
1.Check and clean all electrical connectors
2.Replace distributor with a re-manufactured one
3.Replace upstream o2 sensor
View 13 Replies
I have a 1994 Chevy S10 truck. I been having some problems with it.I was having transmission issues with it (I posted on that one before) , but now it has started leaking oil and I would like to know why. The color of the oil in the oil leak is dark brown and oil gauge is giving me odd readings. For example, when I start the truck the oil gauge says it is half full (40), but it warms up and I am in stop and go traffic it drops to 20. But, If I step on the gas the reading goes back to 40 again for a while and then drops back down again. I thinking about just getting a different truck because this one is becoming a pain to fix, but I would still like to know what could be wrong with it.
View 3 Replies
I purchased a 92 Lumina Euro with a 3.1 and 101,400 miles on it a little over two weeks ago. It has been having problems since I got it.
It stalls intermittently, typically after I drive to work, shut it off for two hours, and then start it to go to my next client(home health aid) sometimes it stalls right after starting it then, and/or sometimes when put in reverse and/or drive and occasionally at stops signs after the aforementioned problems occur. It has also stalled out twice after highway driving after the car is shut off and started shortly afterwards, for instance, when I ran into a tobacco store for some cigs.. After the problem occurs it usually drives ok if I continue to drive it awhile even if I shut it off for a short time and restart.. I added some fuel injector cleaner when I filled the tank but it didn't work.
After about a week of the stalling issues the car refused to start after dying and didn't start for two or three days. As I was unable to get an answer from the dealer my step-father, who went with me when I bought the car, called him and he said if I could get the car there he would fix it. So I borrowed a bundle to have it towed the 25 miles or so to the small town car lot.
His mechanic supposedly fixed it by replacing the TPS and the dealer informed me that they had cleaned the throttle body before I bought it and apparently the TPS needed replaced to. However the issues again started after one day of it running fine. I tired to get a hold of this guy again and again I get the voice mail and no return call so as soon as I got off work I drove it over there and again he said he would fix it. He had it for three days and I again tried to get a hold of him without success and he again answered the phone for my step-dad and told him they had ordered some kind of module that would be in Monday. So Wednesday he calls me and tells me that they didn't replace this module because when they took it out it tested good five times but they noticed some gunk build up at the contacts of the wires that hook to the module and now the car was fixed. Why did they order the part before testing??? This doesn't make sense so it throws doubt on what the man said. I went to get the car and when I got back to my town and went to get those cigs it died twice after restart and put into reverse. That was two days ago and it has been dying once or twice each day since then although it is somewhat better than before as it isn't taking as long for the idle to even out at sufficient rpms after I throttle it at idle or drive awhile. BUT now it seems to be sucking the gas hard and I am wondering if this guy just did some jerry-rigging because he sure isn't fixing it.
A few more details. The rpms drop rapidly when this occurs, it has a couple of times had a rough idle at the same time but more often the rpms drop and it dies.Sometimes if I use the throttle and keep it up around 1000 rpms for a short time it won't die. I have smelt a burnt smell a couple times when I shut the car off, like electric burnt, not oil burnt or stinky exhaust. Lets see, I felt a very brief loss of power feeling when driving on the highway on two different occasions, so brief that it was barely discernable. It runs over the halfway point on the temp gauge after driving awhile in town, seems a little hot to me but I read these cars don't kick on the fan till 220. Sometimes the rpm bobs a little up and down at idle and slow speeds and once the battery power dropped and popped right back up when it was idling funny and when it had that no start an acquaintance tested it by putting a screwdriver in a plug wire and pointing it towards the engine as I cranked it and he said it had no spark and it did crank every time I tried to start it during the no-start condition. It has also done a bit of surging from time to time when the prob happens. The car is recovering from the stall condition quicker than it did before since this last "fix" but still stalling.
View 5 Replies
I have a 89 chevy 1500, 5.7 pick up. I beleive it's referred to as the c/k series.
Recently I've been having some issues with stalling. When the engine is cold everything runs fine but after warm up I've noticed the problem start occurring.
When I'm doing a slow turn ( any direction) , backing up, or in stop and go traffic, the truck want to stall when I touch the gas pedal. Once I get past the intial slight throttle it picks up and does fine.
I've replaced the distributor cap and rotor, plugs and wires, fuel filter and even the fuel pump( mainly because it never gauged fuel correctly but I thought it might have a pressure issue).
Nothing seems to work and I'm not getting any codes.
View 14 Replies
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 Replies
The issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 Replies
