My 2002 Mazda MPV will stall everytime after the rpms go over 2,000 and I let off the gas. I can put it in neutral and it will start back up. Not sure if something is clogged or its electrical? It has 177,000
View 6 RepliesI have a 2001 Mazda Tribute with 150,000 miles that is meticulously maintained. This past winter (as far as winter goes in San Diego) the engine would run rough and the rpm's would drop close to stalling when stopping at a light for the first 2 or 3 miles. After that the engine has warmed and there is no problem. Could this be the intake gaskets needing replacement. This only happens on a cool or damp, rainly morning.
View 6 RepliesI own a 2007 Ford Taurus with about 108k miles on it. When I first start the car, the rpms stay very high (2000) or so for about25 seconds. Once I start the car, until it gets all the way warm, the rpms want to stick around 1300 until I'm stopped for a few seconds, then they jerk downwards hard to almost 400 and come up to around 700.
After the car gets warmed up, it no longer sticks when I brake, but then when I'm stopped it lurches shakes and jerks between 400 and 1000 rpms. Occasionally it will die ( maybe twice a week) but then starts right back up again. I have replaced:
Air compressor
Idle air control valve
Throttle body sensor
I replaced the throttle body sensor yesterday and it seemed to drive better but it only lasted for about 12 hours then the next time I started the car it's doing it again. The only solution I've found so far is that it jerks just a little less when I'm in neutral.
My standard 2002 accent is undriveable and at the mechanic right now (100,000km). For the past few weeks the car has driven very jerky. While in first and second gears if i accelerate too quickly it just jerks/slips and has very little power.
Yesterday the check engine light came on and i got codes P0300, P0302, P0303...misfire in cylinders 2 and 3. Checked this forum and decided to buy new spark plugs (last replaced plugs and wires 1.5 years ago). Got into the car and could go more than a block because it was jerking and then kept stalling. Replaced the sparkplugs and nothing changed. Had it towed to the mechanic...after a few hours he said he had cleaned the exhaust manifold and it was driving fine. I picked it up and a block away it stalled again.
The mechanic now says 3 of my fuel injectors need to be replaced and the fourth will probably go soon and it will be about $700 to fix. Does this sound right for these codes?
I called hyundai parts and they told me each injector is $236...he also told me he doubted they had to be replaced cause he has never seen an accent have fuel injectors replaced and also they rarely sell these injectors, he said it was probably something electrical.
I have found 4 injectors on ebay for $200 but is this really the problem? The mechanic says it is 100% the problem. But from reading the forum I dont think so.
Also wanted to add that i often noticed the smell of burning plastic. Smoke seems to be coming from spark plug area when i notice the smell but nothing looks burnt/melted.
I have an 02 Accent 1.6L that has about 190,000km on it. It is now misfiring under low rpm's (anything under 2000) and the engine light will flash and then go off after about 5 seconds. Once the engine light went on and stayed on but I got the code read and reset it. The code was P 0303 Cylinder 3 misfire. I replaced the coil pack since that is apparently the common cause of this issue.
No luck with the new coil pack still have the same problem. I started smelling gas about 1000km ago so I assume that it is burning rich and putting raw fuel into the engine. My spark plugs are under 10,000km new and the wires show no signs of any problems. My next thought was to buy a new MAF sensor and hope that is the issue.
What this could be? FWIW the engine seems to run a little better for about 5km after using a throttle body clean on the TB. It also runs minimally better when I use a Lucas fuel additive.
I've got a misfire problem with my Focus. It started about a month ago and did not trip a code until last week. It stumbles on acceleration between 2,000 and 4,000 rpms. It is only a slight stumble and although noticeable, it does not impede driveability much. Last week I was able to get it to finally trip an OBD code. P302 - Cylinder 2 misfire. I changed the plugs and wires with no effect. I thought I had it narrowed down to the coil or injector until my wife noticed a new wrinkle.
Under normal driving conditions the misfire is annoying, but my wife found that if she turns on the A/C, it is undriveable and will not accelerate past 30 mph without some patience and a neck brace for the bucking. My first thought was the A/C compressor was freezing up. I turned off the A/C and left the blower on and it would not stop missing. I turn off the blower and it smooths right out to the annoyance I described first.
Right now I drive the car without A/C and blower whenever I accelerate. If I'm going a steady speed, all is well and I can run the blower and A/C.
I am a proud owner of a 06 Mazda tribute 3.0, 6 cylinder, 2 wheel drive, automatic. That is not the problem. The problem is on long drive 100 miles or more when we take a pit stop, to stretch our legs, we exit and when we come to a stop the suv stalls out. Its like we are driving a manual and forgot to push in the clutch. We can start it right back up and when we put it in drive it does it again. If we start it in neutral it will ideal but as we shift to drive it stalls out. We are not seeing any other problems. The MPG are the same and haven't gotten any worse. What should I look into fixing?
View 11 RepliesI was driving my car on the highway, stopped to get gas and it started stalling but would never loose all the power. The check engine light did not go on. They have replaced spark plugs, hoses and it keeps doing the same, they told me there could be water in the fuel i pumped so i burned through the gas, drove 5 hours back home and when going uphill i would give it gas the rpms would go but no speed.
I took it to the ford/mazda dealership in town and said that the codes it was giving em they could not decipher, their best guess was a timing belt issue, they suggested i took it to an exclusive mazda dealership...but the closest one is 3 hrs away. They said it wasn't my transmission. There is no set speed when it stalls..it does it often maybe every 20 seconds or so...the car is a mazda protege 2000 with about 140000 miles...
My Mazda MPV will stall at slow speeds, such as if I am turning a corner or slowing down at a stoplight. Sometimes it starts back up once I put it into park, but other times it takes a few minutes of trying/resting before it will start up. One day, I am afraid it won't start up at all again. I just got new spark plugs and recently got a new mass airflow thingy put in. Check engine light does not come on for this.
View 2 RepliesI have a 2005 Mazda 6. When it is cold - I start the vehicle & begin to drive. When I slow down and the RPMS get around 1000 - the car begins to run really rough & try to stall. If I put my foot on the gas - I can usually prevent it from stalling. The problem disappears once the car gets warm. The dealership recalibrated the PCM based on a Mazda Alert. However, it has not corrected the issue. Looking for thoughts on what could be causing this?
View 5 RepliesMy voyager stalls when rpms are low--turns, backing up, stop signs etc.., RUNS FINE WHILE COLD!!!!!
Replaced fuel filter, iac, whats next!??? nothing shows up on computer - no error codes etc etc....
About 5 weeks ago my 2008 Hyundai accent's check engine light came on. It came on right after I filled up a tank of gas and started running a bit rough. About a year ago the same thing happened, and it turned out to have been because of some bad gas (I ran the tank down, refilled and everything went back to normal). I assumed that was the same thing this time because the gas was from the same location and the problems started right after the fill-up.
I drove it for about a week and then it stalled out completely. Rpm wouldn't go over about 2,000 and if I tried to drive I wouldn't go over about 10mph. I took it into the local shop. Replaced all kinds of fuel sensors, spark plug coils, and the main computer, and I think the fuel pump (all of which got fried). The error codes are all fixed and the car idles just fine. Only problem, when you put it in gear to drive it almost immediately bogs down, rpm stays below 2k (still) and eventually it will totally stall out.
The shop is now saying they think it's the catalytic converter - but they aren't sure. The car idles smoothly now, no error codes. But as soon as you try to drive it barely moves. It feels like there's a governor on the engine or like there's not enough fuel getting through. What to try next.
I have a 2003 Mazda Tribute that seems to have a bit of an idling issue. When my heat on my car is off, everything is fine as far as the idle speed. When I have the heat on, even when it is low, and I am stopped, the rpm's rise a bit, then go back down to normal idling speed. The car also gives a little jump when I come to a stop. I think all of this is related to turning the heat on and off, as it doesn't happen when the heat is on.
View 11 RepliesI have a 2001 vw jetta 2.0l manual. When the car is running the rpms jump up and Down from about 300 rpm to 900 rpm and I guess that's why the car will stall out every time I press the clutch to stop. Also the car won't run with the MAF plugged in. If the MAF is plugged in it will drive but will not idle the car will just stall.
View 16 RepliesI have a 2004 Hyundai Santa Fe with about 83,000 miles. Lately it has been having issue with the rpm's going low and stalling out while I'm driving. I've taken it to a mechanic and it has not been resolved. He said it does not need a tune up and it's nothing with my fuel. I've also heard it could be a crank shaft censor but he says no. The check engine light has come on sometimes, very quickly but then goes off.. He ran the code but nothing came up. So then what's causing my car to do this?? While the car is running and I'm in park, the rpm's will go from 2 to almost 0 then back up again. While I'm driving down the road it does the same thing and sometimes it completely stalls out while I'm going about 40mph. So incredibly scary. What this could be so I can take it back and get it fixed!!!! I'm so scared to drive it but I have to get to work.
View 3 Replies2003 Mazda6, 3.0 liter, 6 cylinder, FWD. My RPMs are starting to jump, so I believe a clutch replacement may be in line soon. However, I'm not a huge car guy, and I don't have much experience in regards to replacing clutches.
(1) The RPMs are jumping occasionally at higher gears (not every time). How long do you think I could go before the clutch dies completely? I'm not a "racer", and I just use my car for daily driving.
(2) Do mechanics replace clutches based on symptoms alone, or can they actually visually inspect the clutch and determine that it needs to be replaced?
(3) When replacing a clutch, what parts need to be replaced besides the actual clutch itself? Also, I've read about flywheels needing to be resurfaced, but is that necessary?
(4) What manufacturer makes good clutches? As mentioned, I'm not a hard driver or anything. Just need something that is good quality and affordable.
(5) Is the best way to save money (I'm a graduate student) to buy an aftermarket clutch and have the clutch installed by a local mechanic?
(6) At what mileages do clutches typically need to be replaced? I know it depends on how you drive. Let's say you're a casual driver and simply use your car to get to work, school, etc.
So here's the deal, I bought this 93 Volvo 940 turbo station wagon about a month ago. It was stalling when I got it so I replaced the rotted hoses, fuel filter and cleaned the fuel system. The fuel pump was replaced a little before I got it. 2000 miles later it is stalling again at any speed mostly when the rpms go up and on hills. We are trying to replace the map sensor but can not find it anywhere under the hood. Does this car even have a map sensor and if so where is it located... We are also trying to clean the throttle sensor but cant seem to get it out without taking a bunch of other pieces apart, is there a trick to this. Is there anything else it could be...
View 4 RepliesI have a 1993 protege that was previously not having any issues. I recently had a mobile mechanic replace my axle after it broke. Since then I have had issues with the rpm's increasing but the speed staying the same or decreasing. This happens mostly uphill and especially when the vehicle is cold. Is there another reason this can occur besides a bad clutch?
View 17 Replies2001 hyundai elantra. Car is almost stalling randomly at stop lights. Low rpms under 500 and stops. Sometimes drops to 100 rpms then shoots up to 500 right before it might stall. Engine light came up got misfire on cylinder 2 and 4 with codes p0440 and u0d00.
View 5 RepliesI have a pretty bad flex pipe leak on my 20th. Would this leak cause a very rough idle almost stalling when I come to a complete stop. The Idle fluctuates from almost stalling to 1000rpms.
View 1 RepliesMy families 2001 Nissan sentra often stalls at stoplights, has low power sometimes in the low rpm's and sometimes (though not always) chugs/jolts a bit at low rpms and has trouble "overcoming" that window and getting more power. If I give it more gas the engine seems to get "normal" at around 2500 or 3000 rpm's and then is fine.
We took it in and the mechanic said it was a bad O2 sensor or MAF sensor... can't remember which. We tried replacing the MAF sensor but it still has the problem. We have heard that we may need the computer re-set somehow or made to recognize and sync up with the new part. As we call around this is very expensive just to make a part that is already installed work. Is this necessary? What's the next, cheapest, step.