Nissan - Maxima :: 1998 - Check Engine Light Come On And Car Started Running Very Rough
Aug 10, 2014
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
View 19 Replies
Advertisement
I have a 2008 Kia Rio, 4 Cyl 1.6L, and recently the check engine light came on and the car started running real rough after getting the timing belt replaced at firestone. I took it back to Firestone and they said that 2 of the cylinders where misfiring and i need to replace the ignition coils and the corresponding spark plugs, but that i also want to get a catalytic converter cleaning or flush or something like that because of the unburnt gas that was running into the converter. Is this true? They want to charge me another 100.00 for the cleaning on top of the 300.00 to replace the 2 ignition coils and spark plugs, should i get this done or can i clean it out myself?
View 6 Replies
I have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
View 1 Replies
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 Replies
I recently bought a 2003 nissan maxima 134k and i bought it with the p0300 check engine light on a looked at the engine and though it was an air box problem because they had previously installed a K&n filter so I went to the junk yard and got a 2000 nissan maxima air box and new filter i changed the oil and checked the spark plugs they look new and the dates on the coils are 2012 and 2013 and still its misfiring. i bought it to a mechanic and he discovered a vacuum tank had previously broke and they glued back together so i replace that with a factory one today same problem still misfiring but it got better but now its a p0306 then i erased the code and p0304 came back i erased it then p0302 came back then i change the cam sensors, and the crankshaft sensor and now it get a p0300.
Symptoms:
*when sitting for a long time HARD TO START ( takes multiple cranks to start it ) but once i leave it off for short time like 30 min it starts right up no problem
* when stop at a stop light in drive i can feel small little explosions sounds like my car is beat boxing
*performance is strong good acceleration no problem on that i just don't want it misfiring
View 14 Replies
Well it finally happened, a couple of weeks ago I was headed to an MX race and my check engine light came on and it started running rough. Long story short a piece of an exhaust valve broke off and went out through the head. Dealer has been great even though I was 300 miles from home and they did get me a rental(small POS SUV). Truck was supposed to be finished this week, but now they are saying the head gasket is on back order and they probably won't have one until the middle of April......... I can't be without my truck that long, but not much I can do. By the way truck is completely stock with just under 20K on it, and I have never had any issues with any of my Ford trucks or Ford diesels, even my old 6.0.
View 7 Replies
I keep failing my emissions because my check engine light keeps coming on. I was told that the problem was the catalytic converter rear and needed to buy one for both sides. The problem I am having that I don;t know which Catalytic Converter I should buy. I know without it is causing my car to stutter. Which I should get?
View 8 Replies
My 98 Maxima won't idle without dying, it sputters when you accelerate, and it tries to die while coasting. I've changed two O2 sensors (AutoZone gave me the code for bank 1 sensor 1 & 2) changed spark plugs, tried fuel injector cleaner, oil change, and cleaned MAF sensor & checked the wiring. It;s still spitting out the black exhaust. Although after changing the O2 sensors it quit for about a day or two but started again (I'm guessing the other sensors need to be changed to) But the main problem is once it warms up, it really runs like crap, and is a major gas hog. I'm getting about 12 Mpg.
View 19 Replies
My Nissan Maxima GLE 2000 is showing CEL with code of P1320 ONLY, and the car is running rough/or loss of power. The shop that checked for the code advised that it could be something related to Ignition, and also provided me with the system generated list of reasons for the code. Before I decide to do anything, I wanted to check what option I have to address this in a most cost effective manner:
1) Is there a quick way to check which coil would have gone bad ?
2) Is it advisable to change 1 LH and 1RH at a time, and see if it fixes the problem ?
3) Could it be cam shaft sensor that could have gone bad ? Are there any symptoms of cam shaft sensor failure to isolate it to one way or the other ?
View 1 Replies
I have a 98 frontier 4 cil. 4x4 manual transmission. The CE light is on telling me that the evap system needs work. I replaced the purge canister valve and now the light wont go off at all. You can clear it all you want, as soon as the truck starts the light come back on.The truck also runs rough, bucks at certain RPMS has no power and bad gas mileage. Within the last two years I have replaced; catalytic converter, fuel filter, plugs, wires, cap & rotter, transmission and clutch, air filter, cleaned the MAF sensor.
View 11 Replies
Lets start at the beginning. About two weeks ago my girlfriend got a check engine light and the car started missing( 98 Passat 1.8T, 5 speed). Checked obvious things like fuel delivery-good. Pulled coil packs and had no spark on #2 cyl. Investigated more and found one of the pins on the ign. control module was shorted. Felt pretty sure that was the problem since everything else checked out. Ordered a Huco installed it and that fixed the problem except the car seemed slow reprogramming to the new part. I disconnected the battery to clear the memory and that seemed to do the trick.
About 2 weeks later my GF is coming home and fortunately it died in front of the apartment. Checked everything again. Getting fuel, no wires shorted on ign. or fuel harness plus they all get power just no signal when checking with an LED tester. Ign. module was good also. Checked speed sensor for resistance per the book it was good. Tried a new Camshaft Pos. Sensor hoping that was the problem, no luck. I believe it must be the computer. I'm trying to get one from a salvage yard. I don't know if the old computer can be reprogrammed or not. Also was wondering if the dealer(where I really do not want to go) can test the computer somehow and tell me if it is bad or not(don't know if I would trust them anyway), just wanted to include that option.
View 7 Replies
My mechanic tells me I need the intake manifold gasket replaced (check engine light on, engine surging, running very rough). How much damage can I do to the car by doing this repair myself and screwing it up? I've done lots of repairs on my car before -- brake pads, rotors, replace oil pan. I also have a copy of the manufacturer's shop manual.
View 2 Replies
Our R32 has 2428 miles- and today the check engine light came on and it started to run pretty rough, babied it home and the the light was blinking when I turned into the driveway.. I know that booklet 3.2 in the owners manual is diagnosing catalytic converter issues...I have always used super unleaded, it hasn't even reached the halfway point of the first service.
View 10 Replies
Filled tank with 8 gallons of 91 octane to top off. One hour later noticed car running rough at idle then check engine light comes on. Could it be the coil pack? Car has been running very well until now, and this Gremlin appears. I don't think it's the gas.
2004 -V8 Treg
52,000 on the odometer
View 4 Replies
I recently replaced the head gaskets in my 2003 Malibu. First time and all seems other than it runs rough at stop lights. The check engine came back on and so I had it read and there is an air flow issue. Is there anywhere that I can get a schematic for the vacum lines? I have all over and cannot seem to find a loose or broken one.
View 3 Replies
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 Replies
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 Replies
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 Replies
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 Replies
i have a 2008 maxima with 30000+ miles. its service engine soon light came on recently. i disconnected the battery the light would go off, but would come back on again after a few days. it happened several times now. once i got a code P0011 from autozone while the light was on. the last time the light was on was a week ago and this time the light finally went off by itself yesterday. i took my car to a dealer today. a service advisor told me the reading on his code-reader is NO CODE and the car is fine!. so what have happened and what is wrong with it? could it be serious?
View 4 Replies
I just purchased a 2000 Nissan Maxima GXE with 219,000 miles. I've had it less than two weeks, and the Service Engine Soon light just came on. I live somewhere that requires emissions testing in order to register the vehicle. My temporary plate will expire soon, so I need to get the car to pass emissions.
This is my first Japanese car and first non-American vehicle. I didn't know until after I had given the check to the guy selling the car that he used premium gas. He said that Nissan recommends it. I've never driven a car that required premium gas before and wasn't keen on the idea since here, it is 40¢ a gallon more expensive than regular unleaded.
I spoke with my landlord about it, as he is a certified Honda mechanic. He told me to first try getting half a tank of regular unleaded and putting it in with some fuel injector cleaner. He said if I didn't notice any decrease in performance or knocks, to then just add a bottle of of fuel injector cleaner to every other tank of gas.
I got a half tank of regular unleaded with a bottle of fuel injector cleaner and didn't have any issues. I then filled the tank with regular without any fuel injector cleaner. I used about ¾ of that tank when the service engine soon light came on. I took the car to Valvoline to get the codes read, and while they couldn't give me any code numbers, they said it was something to do with emissions.
Here are my questions:
Is it possible the light came on because I switched from premium to regular unleaded or perhaps because I would need to add fuel injector cleaner to every tank of gas I get and not every other tank as my landlord said he does with his car?
Should I try either adding fuel injector cleaner to every tank of gas or just switch back to premium? If I try either of those, and one of those was the problem, how long would it take for the Service Engine Soon light to turn off?
View 10 Replies
