Encountered this check engine problem > 16805 and 16815 < I replaced the 02 sensors, problem solved for 1000 kms, and now the dreaded light is showing its face again ! Possible secondary air system at fault? Cat about to go, or already gone?
View 5 RepliesGot a check engine light, whoever scanned it said something about a secondary air intake? Upon searching, I found a post about a bad MAF.
View 2 RepliesMy 2006 W12 has been trouble free since taking delivery over a year and a half and 30K miles ago. Just broke 60K total miles over the weekend and the engine light came on. I have pasted the scan below. I cleared the codes and drove about 500 miles before the MIL reappeared. I have read this thread: [URL] ....
My first question is: Is there any harm in continuing to drive it?
I have visually inspected the secondary air injection system hoses and can't find anything glaring (no kinks, leaks, disconnections). I am open to taking the car to the dealership but I have low confidence in their diagnostic capabilities. I am fine with them doing work once we know what is wrong but I want to tell them what to do (replace a bunch of hoses for example). How to proceed?
Address 01: Engine Labels: 07C-906-018-BAP1.lbl
Part No SW: 07C 906 018 AJ HW: 000 000 000 00
Component: D1-6.0L-AT-LEV2 G 6722
Revision: --H01--- Serial number: VWZ3Z0E5400307
Coding: 0000173
[Code] ....
Check engine light is on and my code reader is giving me a P0000 code that is not listed in the Bentley's list of OBD II codes. My nose is telling me it's emissions related as the exhaust smells too rich. And the car is nearly stalling at idle. Suspect #1 is the MAF but the OBD II code does not support this.
View 13 RepliesI have a 2006 passat and the check engine light came on so I performed a scan, the results are below. fault codes... which ones would need to be repaired immediately?
VCDS Version: Release 805.1
Data version: 20080823
Tuesday,06,March,2012,18:12:35:26365
Chassis Type: 3C0
Scan: 01 02 03 08 09 15 16 17 19 1C 25 42 44 46 52 53 56 62 65 72
VIN: WVWAK73C86P106340 Mileage: 107910km/67052miles
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
[Code] ....
Earlier this week on my way back home from the gym I got my first check engine light . I scanned the car and got the fault below. What may be causing it?
About the car: 2008 LUX Wagon2.0T FSI50,2XX miles
Scan:
Address 01: Engine Labels: 06F-907-115-AXX.lbl
Part No SW: 3C0 907 115 S HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH16--- Serial number: VWZCZ000000000
Coding: 040C010A19070160
Shop #: WSC 25129 444 59131
VCID: 3041DE6FDAB3
1 Fault Found:
008583 - Bank 1; System too Lean at Idle
[Code] ....
2002 Passat 2.8L... I am averaging 11.8 mpg in city driving I do not know what the problem is... My check engine light just came on fault P0114 something like that secondary air hose could this be the cause of me getting 11.8mpg and I use grade 91 and higher of gas...
View 6 RepliesJust got a check engine light last night. Pulled the code and got a P202a fault. Some digging indicates its the Ad-Blue tank heater module. TDI forum indicates its anywhere from $850 to 1K to fix. Also that it's not covered under any extended warranty (now there's a shock!) The cars going back to VW so that's not happening.
Is this one of the conditions that will cause the car to go into limp mode at some point? I know that happens when the ad-blue runs low. I'm in Florida so the heater isn't really a big deal. I need to use it another couple of months and I don't want to have this thing leave me stranded. If I have to I'll park it.
I recently had a check engine light come up on my 2004 r32. Dealer told me that the secondary air pump is broken and needs to be replaces, codes that came up were p1432, p1423, and p1411.
I replaced the pump and the next day I heard the "vacuum" sound of the air pump so I know that it works. A day later my check engine light come on again, and I cannot hear the pump anymore.
Now I just changed the pump, not even the rubbery inserts as I didn't know. The pipes seemed to be fine. I checked the quote from the dealer and they also mentioned that the intake pipe is broken, part number 1J0-131-128-AB.
Is that one of the pipes that is connected with the secondary air pump or it's the main intake pipe??? If it's from the main intake, is it possible that the secondary air pump want work because of that???
Should I change the rubbery inserts on the secondary air pump??? Is it safe to drive until I take care of this?
I recently had some work done on my 2001 1.8t Passat. All new vacuum hoses & camshaft tensioner replaced by VW dealer. Check engine light is coming on and an independent shop near read out a code: Bank 1 mixture adaptation(multi): System too lean.
What does this mean??? And could this relate to these parts being replaced??? Work was done approx 2000 miles ago.
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.
I've had my 2000 V6 Passat in for service three times with Secondary Air System issues - the dealer said that the whole thing needed replacement. The indy shop identified a couple of things to repair but said total replacement was unnecessary. A secondary airs system valve has been replaced twice (same one both times). Check engine always comes on within a day - we took it to another dealer for their opinion and again. Said that I need to replace the valve (third time!).
View 2 RepliesI recently bought my new (For me) R32, the first owner of the car remove the 2 catalyst from the car and now I have the check engine light on. When my friend put the vagcom on the car it shows an oxygen sensor fault. What can I do to fix this? can I just buy a MagnaFlow exhaust?
View 11 RepliesI driving 2011 Sonata. Check engine light was ON while driving, which are fault P0741, TORQUE CON CLUTH ABNORMAL. The light sometimes ON, and sometime will OFF while driving, is it any problem?
View 5 RepliesRecently got check engine light fault code p0320
2005 3.5 with 172k miles
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 Replies1996 izusu rodeo had check engine light on got code for egr valve. Replaced it light when out drove fine all day. Stopped at grocery store came back out would not start ... Will crank over but will not start. did a obg (two) scan get a p1640 output A circuit fault code along with a 1460 egr code ....
View 5 Replies99 Ford Ranger 4-cyl. Check engine light is on; pulled fault code: "catalyst efficiency below threshold, bank 1." Cat converter is new as is rest of exhaust, o2 sensors are new, and its been recently tuned up.
View 6 RepliesCheck engine light came on and stopped by the local autoparts store to get the error code.
Code: P2270
Bank1 Sensor2 fault
Where is this O2 sensor? I've replaced O2's on other cars I've had and just want to make sure I replace the right one.
Turns out I've lost nearly all of the coolant from my secondary cooling system and am trying to diagnose the problem.
Things I noticed:
-All of the hoses appear to be in good condition.
-Coolant is dripping from the center of the engine bay.
-After inspecting the turbo area, it appears the valley below the turbo is wet.
The intake manifold is still on the truck, so I haven't been able to get a better look. Is there anything else near the area I am describing that has coolant? My guess is the turbo water inlet?
Perhaps this : Coolant leak on the 6.7 Powerstroke diesel - YouTube...
i have a b.5.5 V6 4motion and My check engine stays on the majority of the time. I've had a tech check the code and he tells me its my Evap system. The same tech told me that it was actually pretty useless to repair the problem unless the check engine light bothers me..
View 5 Replies