Phaeton :: 2004 - Digital Sound System Failed / Navigation System Unavailable Error Message
Sep 27, 2011
I have a 2004 VW Phaeton.
Today, the sound system failed, then shortly after, the navigation system failed.
On the console, if I press any map/navigation buttons, the error message "Navigation System Unavailable" is displayed.
If I press an audio related button, the error message "DSP system is unavailable". I took it to a private vw repair shop and a vw dealer. What was causing the issue.
I am now headed to a vw dealer with certified phaeton tech. I looked towards fuse issue, but they appear to be ok..
View 10 Replies
Advertisement
I cannot get any sound from my DNS! Everything was working fine a few days ago when I turned off the audio system by tapping the Power/Volume knob. I tapped it today and screen comes up as it normally would but no sound. The volume is turned up to max. No sound in FM, Xm and no navigation instructions in the Navigation mode. It is as if I hit the "mute" but if I did I don't know where the mute button is located.
View 5 Replies
I've been getting this "system fault workshop!" error message popping up like crazy. Its got a picture of a key, and makes the audible beep when it appears. on a short drive to work, maybe 10 minutes, it will randomly come on and beep anywhere from 3-10 times during my drive. The car starts and drives perfectly fine. This has been happening for a little over a week now. I noticed one post about this before, but that owner seemed to have different symptoms as their car wouldn't start. I really would hate to bring it into the dealership, as I've just paid them a small fortune fixing different things to finally get down to the bottom of it to find out i needed new fuel pump modules.
View 3 Replies
My wife drives a 05 GX470. Is there a way to disable the caution message (i.e. Caution: Drive safely and obey traffic rules...) that appears on the navigation screen every time you start the suv?
View 5 Replies
I was playing around with the navigation system of my 06 RX400H because I read about the motion override online; however I was being stupid and chose the wrong option under the "load" menu, so the navigation system kept telling me "insert correct disk. ". Hoping that I could find a simple "reset" option there, I was playing with the diagnostic mode quite a bit. One setting allow you to select the navigation unit start up logo between Toyota, Lexus, and None. There is another interesting option called "car setting" don't know what it does.
Seemed like it let you toggle between a numerous of settings, I remember one being 9001X4WD or something. I didn't know what the setting does and accidentally changed the vehicle setting for my navigation unit. After confirming the edit, I realized that the mapping for all the buttons on my panel completed changed! First of all the map button (which wasn't working at the time because I had the wrong load option) became the "Audio" button that is similar to the audio button on my other car, 06 IS350, it showed me all my audio presets and I could choose using the touch the screen (normally this feature is disabled for RX400H).
I realized I might have screwed up the setting and wanted to change back to the original vehicle setting. I couldn't find much information online, so I figure I probably hit that set button by mistake 2 or 3 times, so I reverted the car code back to what it was 3 selections ago, and bam! My panel buttons are messed up even further! Now I don't even have access to the "info" button any more! I can still get access to the first level diagnostic mode using the "display setting" (display key is mapped to the info button now) then left upper corner + left lower corner method, however I can't change the vehicle code in this mode.
I took the car to a local dealer, and the service tech was like "what the heck did you do" and he said he don't know how to fix this except to replace the whole navigation ECU which would cost thousands of bucks. I asked him it would be as simple as getting access to the onboard ECU memory and rewrite it and he said the data format is Toyota proprietary and the dealer doesn't know how to fix it.
Of course I wasn't satisfied with the answer I got, I took the car home. Following some good information on forums and navigation ECU replace instructions on AllData, I was able to remove the navigation ECU from the car, then took it apart, disconnected the power daughter board, pushed the black reset button(?), and then put everything back together. I have seem people saying this method working and not working, but for me it did work. When I restarted the vehicle, the "loading data do not turn off" screen came on, and after the system booted, GPS navigation is working as usual now. On e interesting observation, before the GPS unit has established a connection with the satellites (took about 2-3 minutes to do so), the default location for the vehicle in the system is somewhere in Washington D.C.
Now I have undone my "load version" mistake. However, without the "info" button being mapped to the dashboard, I don't even have access to the menu where you can change the "car code", so even if I know the correct code now, I wouldn't be able to enter it. also it seems that I was able to reset the ECU when I took it apart, I am suspecting that the setting for "car code" isn't store in the ECU but it is stored somewhere instead.
View 14 Replies
I have a 2006 RX400h. On 3 occasions I've been stranded. The car won't start and I get an error/message Shift to P when Starting. However I am in Park. It's coupled with a Check VSC System warning. Service department says I have just drained the accessory battery, however nothing is being used other than standard equip such as lights, dash etc. I've had all batteries changed in the car over the 4 years I've owned it. Is this usual?
View 14 Replies
I have had a problematic navigation system that loses it way some times (loss of GPS signal). However it worked for sometime without problems till I dent my rear left side and had to be in the shop. I guess they disconnected the batteries and now the unit has stopped working. This is the relevant VCDS output. Most importantly I checked the adv measure feature to find the following statuses
CD ROM OK
GPS Antennae OK
Available Satellites 8
Satellites in view 0
GPS Status None
This was a clear day and so the unit is not picking up the satellites. However VCDS output shows no faults or anything.
Address 37: Navigation
Labels: 3D0-919-887.lbl
Part No: 3D0 919 887 A
Component: NAVIGATION 9968
Coding: 0400000
Shop #: WSC 02134 444 59226
VCID: 326BD7F1AE43028E5D3-5140
No fault code found
[Code] .....
View 3 Replies
We bought our ES350 used a number of years ago. When we changed the battery, the Nav system no longer worked and a " A program cannot be read. Please consult to a dealer." message appeared. Am I wrong to assume that the loss of power from the battery swap caused the software to dump from the system and there was no disc installed to "reboot" the system? All I need is a disc and the system will restore? If so will an "update" disc work or do I need an original "program" disc?
View 1 Replies
I was driving my NHW11 in the hot sun this afternoon when, about 30 minutes of pleasant and unhurried driving, I got the dreaded 'hybrid system error' message...
View 10 Replies
1. I think my battery is getting weak.... when i cranked it, it didnt sound strong and the original battery eye says to add distilled water. I am thinking about getting a replacement battery at Costco.
2. so right after it started, the message of "Check Brake System" shows up. Tried to restart but no go. Drove about 15 miles and all seems fine but message is still there.
* is it OK to replace with a Costco brand battery (they have a great returns policy) and is there anything i need to do before or after replacement?
* could the Check Brake System be due to the weak battery? How can I reset it?
* Anything else that can cause this error message?
View 3 Replies
So with all of the snow we've been having in the north east this is usually an error message I get almost every week. Normally this is due to the front sonar sensors being covered in ice or snow and will go away once it melts when I'm parked in the garage or is washed off.
However the past few days, I've had the car washed a few times to make sure the salt is off of the sonar on the front bumper but I'm still getting the error message stating to check the front sonar. If I leave the park assist on it works for the sides but not the front and the error message still stays on the screen. I've hand-washed the sonar sensors several times and 'massaged' them in place to maybe break up some ice behind the bumper or get the sensor to work but I've gotten nothing. Upon further inspection, one of the sensors has a deep scratch in it to where you can see past the paint of the car slightly.
I'm really not looking forward to taking the car to the dealer to have them look at the sensor because they will most likely charge me a ton. I saw a few other posts on the forums about the LS400 from '99-'00 having a similar issue and it cost them $550 to get it fixed. Obviously it's not the same car but I'm expecting a similar quote. I'm assuming the paint scratch is what is causing the issue as another post for the LS mentioned the same thing and said they had to scratch all the paint off of the sensor to make it work again.
View 5 Replies
The "car" symbol on the nav screen seems to lag the actual position by up to 1/2 block.... when I make turns onto another street, for example, the map will sometimes indicate that I am turning into the block itself (instead of the street that I am on), and about 1/4 mile later, it will mysteriously "shift" the car location back onto the correct street.
View 24 Replies
My 2008 LS460L has been periodically displaying the following message in the dash display: "VSC System Error" ...
This message displays on and off about every other day. Yesterday, I hooked an OBD2 scanner up and discovered the following error code history:
P0171 : System Too Lean Bank 1
P0174 : System Too Lean Bank 2
P0022 : "A" Camshaft Position - Timing Over-Retarded Bank 2
P0335 : Crankshaft Position Sensor "A" Circuit
P2195 : 02 Sensor Biased/Stuck Lean Bank 1 Sensor 1
Every now and then the engine will run a little rough, but usually at low RPM, and (again) not very often. The car has 166,000 miles of mostly highway driving.
View 14 Replies
Have an early 2004 US Phaeton with the smaller sound system. Everything works normally on the system, but when putting some commercial CD's into the player can yield some really nasty clipping (clicking on drum-beats or other high-frequency sound) on the loudest sections. The clipping only occurs on the loudest sections, irrespective of how high the volume control is, and it only occurs when listening to the CD.
This is either a defect in the digital/analog converter in my particular unit, or it's a design defect with the whole series. For techies, the highest bit (#15) in the D/A is feeding an overload signal into the analog path of both channels. This symptom also could occur on CD's you burn yourself if you tend to record your CD's really loud (right up to the limit of CD dynamic range).
View 3 Replies
I have Lexus 460 LS L 2007. Few months back changed the battery and every thing was ok. 2 months after I had problem in the sound system ( radio and dvd ) which was on and off. One month back suddenly I had all the warning lights in the dashboard on with massage saying that that the brake system is malfunctioning and check the ABS system.
I took the car to LEXUS dealer and they reprogrammed the computer abd then every thing went back to normal and the problem fixed. Two days after I had these warning lights again with the same massege. I do not know what to do ??
View 4 Replies
I just got back from being gone awhile to find that my rear view camera has stopped working. I get a message that says "rear view camera system is currently unavailable" when I put the car in reverse.
The camera does come out like it should so I'm guessing it's something to do with wiring maybe a short or something. I have a 2014 RCD-510 with the camera input...
View 6 Replies
In the past few weeks I have seen an intermittent "Level Error-Workshop". However every suspension function has worked perfectly, and no height was lost even while sitting at the airport for a week.
How to track down the leak. I can see a tank pressure of about 13 PSI. Is that about right. I did a raise / lower while VCDS was connected and there was a pressure drop to about 11.7 PSI but no level error. What is the correct range of tank pressure settings?
Address 34: Level Control Labels: 3D0-907-553.lbl
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0005521
Shop #: WSC 01065 000 00000
VCID: 2757057592F60B6
1 Fault Found:
01583 - Leak in System Detected
000 - - - Intermittent
View 4 Replies
After replacing at a Toyota dealer in my country the JBL 6CD audio system under warranty (was not responding on the commands from front panel, the unit was faulty), I've found some error codes left in System Check Mode and I don't know what is their meaning. What those codes show, especially 380H error code? Here is how to look ...
View 4 Replies
I just realized that I should be hearing the nav system giving me audible turn notifications. And I haven't been getting them. I have a destination entered, and am in the middle of being guided.
Having the audio system on/off makes no difference
I have the voice guides turned on (via Menu screen)
I have the voice volume set at 7 (via Menu screen)
Turning the speed-adaptive volume on/off makes no difference (via Menu screen)
I am on what seems to be the original DVD disc (v3.0?) that came with the car
I have what appears to be a dealer/aftermarket installed rear entertainment system (not OEM)
So:Does the nav system audio have it's own speaker and dedicated channel in the ML amplifier? Or perhaps it's own amplifier
View 14 Replies
I was recently in a rear-end crash. The body-shop presumably disconnected the battery, fixed the rear door, and then re-connected the battery.
Now, however, the Navigation screen just flickers.
If I press Info, Audio, or Climate, the screen is just fine
If I press Menu, Dest or Display it flickers.
(Curiously, if I press Info, Audio, or Climate AND THEN press Display, the DISPLAY is fine)
Took it to the dealer, who said it was a coincidental to the body-shop repair.
View 1 Replies
I bought a 2003 GX470 a couple of months ago and love it. It was a good upgrade from the 98 Land Cruiser I had a couple of years back and much better than my recent X5. Even though it runs great right now, I have one issue bugging me.
The Navigation unit hasn't ever really worked. Actually, it works, but since I bought it has used the secondary system which calculates location based off direction and speed which is only accurate if driving 50 yards or less - even after calibration
I found out how to get into the secret menu and looked through the settings. When I go to the screen which shows connected satellites, it says "Ensure nothing is blocking gps reception." I've tried a couple of resets, but nothing seems to work. I looked up where the antenna is to see if the connections is loose, but the only reference I found said it was on the rear glass. Unless integrated into something, I don't think it is, though.
The system still runs a factory 2003 disc for maps which is Gen 3. I tried a used 2007 map disc which upgraded the system, but didn't work. It gave disc errors so had to go back to the 2003 one. I haven't had a GPS signal since the day I bought it.
View 5 Replies
