Phaeton :: Car Starts Fine But Dies After 10 Seconds
Apr 30, 2011
I have an 04 w12 with 80k miles on it. It will start fine but will not run for more than 10 seconds. As it idles down from startup it settles to about 700 RPM's where it normally does then dies. If u drive it it will start and go into gear fine as u go to pull away it loses all power and dies. I have checked the minor things i know like air filters, oil, tranny juice all appears normal. New batteries less than 3 months ago also.
View 11 Replies
Advertisement
I am working on my father's boss' 2004 Phaeton V8. The car usually sits on the weekends. What it is doing is, it will start and run smooth, but after 15 seconds, on the dot, it stalls and dies. It sounds like it is starving for fuel.
What I have done so far:
LH intake actuator arm found broken, replaced both with "Gruvenparts"
Checked all fuses and relays
LH fuel pump reads 14 volts until the relay kicks it off
Tested fuel pressure-good
Batteries fully charged
LH fuel pump reads 0.7 ohms w/key off
RH fuel pump reads 6.0 M-ohms when first connected and gradually climbs to 31.5 M-ohms
(I assumed this meant RH pump was bad and so I pulled it out and bench-tested. Ran perfect and tested at 0.7 ohms out of the car)
Re-assembled everything to pull the car out of the shop, and wouldn't you know it started and ran like normal.
Road-tested for 2 hours the next day without any problems.
So, I call the customer to pick it up and he says he will be there 2 days later.
View 15 Replies
A few days ago, I went to start the car, and it will start, and idle fine for a few seconds, and then begin to run crappy, idle down, and die. I tried starting it, and giving it some accelerator pedal, and it dies. I changed the timing belt, idler pulley, and tensioner this summer, so I'm ruling out a bad timing belt. There is no check engine light, and I replaced the plug wires because when I removed the cover, I noticed one of them was worn in a spot, and the wire shielding inside the rubber insulation was visible.
View 11 Replies
I have a V6 with 162,000 miles. A year ago in the early spring we replaced the alternator, starter, fuel pump, lines, filter, dropped and cleaned the tank, fuel coils, repaired / replaced almost all injectors, spark plugs.Since April of last year, every few months my Car would have a hiccup of that it starts fine but would immediately die out. It would take anywhere from 5 to 30 minutes of trying to get it to start again. Other than that it would run beautifully. This week, while on the road it would jolt and die out. It happened 3 times. Yesterday morning it would once again crank fine and immediately die out. It will no longer keep running. We have not been able to keep my car started since then.
View 14 Replies
I've been having some issues with my mk4 R32. Right now i'm leaning toward changing the fuel pump and filter but i want to be sure before i do.....
Problem: I've been daily driving my r32 to work for the past couple weeks and about once a week it will start, idle for a couple seconds and then just bog out and die. no codes, just idle, then chugging and dying. it will fire with some starter fluid and will sometimes hold a very sickly idle but most the time will just run the starter fluid out. the weird thing is is that it's intermittent and will happen randomly and if i leave it overnight or sitting for a couple hours it will fire up like nothing was wrong. i just wanted some input on what it might be before i replace the pump. i have already done the relay so its not that.... the only code that it has ever thrown while i have owned it was for the intake changeover valve (N156) which i cleared and it hasnt yet to come up again.....
View 14 Replies
Our car starts, then dies. It starts fine, then dies. This only happens in warm weather, which we have finally been experiencing in Northern Illinois. It eventually gets to the point where we can drive it, but then might die at a stop sign, or it can go the rest of the day and not have any difficulties. I know later models have timing chains, not belts. Does our car have a timing belt problem or maybe fuel pump? And why only in warm weather?
View 7 Replies
Having some problems with my 92 Nissan NX2000. i just finished changing the clutch on the car now its acting horrible.
When i start the car, it will run decent for like 2 or 3 seconds then the idle drops down till it almost dies, catches itself, idle goes up to about 500 were it will pulse around for a few seconds until it dies. If i rev it it will stay running, kept it running for about 2 mins. but as soon as i let off it will pulse at 500 until it dies
After i changed the clutch it started up fine, it ran great for about 20 seconds before it just died. when i started it after is when the problem arose.
I took a video of the car running, which can be seen here. [URL] .... (It has never caught itself like that before and jumped up to 1000 rpms before. It normally will die at that point)
The video is really quiet, not sure what happened there. if need be i can get a video of the engine bay so its louder, was mainly focused on the RPMs.
Here's a few things i tried: Checked fuses, Changed spark plug wires, made sure they were all seated good, MAF wires were rubbed a bit so i cut the MAF pigtail off one of my other sentras and soldered it on,Changed to a good battery, Changed fuel filter, Added more gas (in cause gauge is broken), Made sure all connectors are plugged in, Checked around for vacuum leaks, found that one of the large hoses coming off the intake going to the engine had separated so i plugged them back in and nothing.
View 4 Replies
I've shipped my R32 back to the UK, the combination of cold and damp weather has taken it's toll on my car. I started it up Saturday and left it ticking over to allow it to warm up before driving it. The car is used to Houston heat, so a few minutes running will allow the oil to warm a little as the weather here is around 40F at the moment. The car ran for 5 or so minutes, then stalled.
The car starts to about 3 seconds, then dies. I have checked VAGCOM, the only fault is a steering wheel sensor (?). It has a full belly of Shell 99 RON fuel and was serviced just before if left the USA in October.
I have had it towed to the local dealer for repair. I have tried disconnecting the battery for 30 mins to reset the car, it didn't make any difference. I have also tried another key in case it's s sync problem.
View 10 Replies
I have a 04 late model F250. I have done the EGR delete, oil cooler upgrade, and blue spring upgrade. I have a SCT tuner but truck is currently set to stock.
My issue is it starts fine runs good but dies after about 2 minutes. No stutter or stumble. It acts as if some one just turns the key off. I have to let it sit for about 2 minutes and then it will restart. If I try any sooner then it just cranks but will not fire. This started about three weeks ago. At that time I would be driving and it would just die. I could slip into neutral turn key and it would fire right back up and I could continue down the road. As time has gone by the issue has reoccurred more often and now I have to let it sit for about 2 minutes to get it to start again but then as stated only runs for about 2 minutes and then dies again.
I have a scangauge and here are the readings I can get.
FICM main power is 47.5 - 48 volts at all times = good
FICM Logic power is 10.5 - 11.5 volts at all times = ???
IPR is 33% at idle = good Scangauge does not react fast enough to get info at startup.
ICP voltage KOEO 0.25 volts
Start 1.33 volts
Idle 1.11 - 1.13 volts dips briefly to 0.96 volts
ICP pressure Start 900+
Idle 830ish
Sync between CAMshaft and Crankshaft is 1 = good
Have not gotten fitting to do fuel pressure test yet.
View 14 Replies
So i start my car and it starts easy but after a few seconds it dies. I can get it to keep running by changing the fuel mixture but then it has no throttle and it will die if i try to use the throttle. It is 1985 VW Jetta engine in a 1981 Scirocco
View 2 Replies
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
View 2 Replies
I have been suffering from LH battery drain for some time now. sometimes its random I will park it for 10 min. come back and the battery is drained (I have to use the key to gain entry). sometimes it only happens over night, where other times the battery doesn't go dead overnight. so last weekend I decided to change the brakes...That was easy but then I forgot to hook up my battery maintainer...so you know what happened! now the problem is I charged the battery and hooked it back up. No start! everything works fine the battery is fully charged and only 1 year old.
But this is the weird part if I disconnect the starter battery the car starts up fine. I hook both batteries back up and try the parallel start way (turn to start then full counter clockwise then full clockwise several times no luck). the LH battery is drained now after a few start and stops (no driving) and the starter battery is fully charged. but with both batteries hooked up it wont even attempt to start and now I also have no power to the power trunk!!! this car is starting to suck balls.
View 12 Replies
2006 ... HV battery changed over 4 months ago and car ran fine until last week when the car just stopped and won't get ready. Before that incident, the vehicle was running fine all day, while he was returning from the days chores in the evening, it just stopped, dashboard all lit up. After a while, the car started again, and he was able to move it away to the side of the road...just about 2 meters and it stopped again.
View 15 Replies
I have a 2005 ranger SOHC 4.0 new rebuilt engine It starts then dies after a few seconds then doesn't start at all unless it sets for a few hours or over night and will do same thing. It has 60 psi on fuel rail, good spark I'm starting to think my PCM is causing all this?
View 14 Replies
Went to start this 5.0 TC after it sat idle for a week, and it died within 3-4 seconds. Further attempts resulted in similar response. After some initial checks, I was able to keep the engine running by manually depressing the IAC plunger into the barrel. The engine ran fine as long as I could hold that, but stall immediately after release. Codes: TPS out of range; HEGO HO2S sensor out of range-always lean. Bought a new TPS no change.
Today: With the key "on" and engine off, the fuel pressure is a steady 38psi. There is an air release button on the fuel gauge line and when I pushed that, the gauge pressure dropped to zero and does not come back (until you key off and on again). I removed the IAC from its mount and with the key on--I observed the plunger move inside its body--guessing maybe 1/4 inch. I casually checked all the engine management items I see in books and looked at vacuum hoses and couldn't see anything amiss (also climbed on top of this engine and checked the rear--PCV lines etc.). I removed the fuel regulator vac line and observed no fuel leakage there.
View 1 Replies
It's a 05 Kia Rio. I've recently put a bit of work into it due to a few issues which were fuel related, namely replacing the fuel filter/pump. It also has brand new spark plugs. That solved the issue that originally put it on blocks for a few months and it ran fine for the past few weeks.
Today I went outside to drive to work and got the symptoms in the title. I know it's not a spark issue because it does start, and I used it on accessory to air up my tires this morning.
I'm just not sure where to go next. I've done a bit of searching and have found recommendations for checking the grounds and the distributor cap.
While running at rough idle, depressing the accelerator makes it die faster, rather than keeping it running. It rained last night and this morning. It's about 70 outside instead of the 80-90 it's been the last few weeks. No check engine light, but I've only tried to start it about 10 times.
View 2 Replies
Have 2005 Phaeton with about 140,000 miles. Has run fine as long as I've had it at about 100,000. Last week it died in a parking lot after starting. It keep doing that all the way home.
Next day it started and ran a bit longer and then the serpentine belt broke. Replaced the belt and car ran fine for 10 minutes, parted it and the next day it quit after running 2 minutes.
Seems like it dies right after the computer systems cycle up.
I replaced the left side battery and keep the correct charger on it to make sure its fully charged. I start the car and it dies after a few minutes, then I notice the charger is charging the battery.
I checked the J367 battery control unit and its a D rates 2800 so should be the right one. I don't know if they can go bad. But think it could be the problem, not sure if they can be tested. Called my vw dealer and they say they need to whole vehicle.
The meter on the dash show 14 plus so I think the alternator should be fine. I did check to make sure all pulleys were turning smoothly when I changed the belt. Today I checked the Smoothing Capacitor and it tested fine.
View 16 Replies
This must be the week for Phaeton issues.
This evening as I was leaving from work, I started the car up and within a minute it died. I thought it must just be the cold, so I started it up again, and again it died. I had driven the car to work this morning, then taken it out at lunch time to run an errand, and everything was fine. I decided to drive the car to see if it just needs a charge, but again, as I was pulling out into the street the car died again. And again across the street in a big parking lot. Eventually I just pulled back into work, called the wife to pick me up and to bring along the vag-com cable and her laptop.
While waiting, I decided to start the car again, and again it died. So I wait, and once my ride arrived, I plugged the vag-com in and did a read. I got some initial intermittent faults, so I cleared them, started the car, waited for it to die, then did another scan to see what happened. Couple of things came up: Intervention load management kicked in (00907) and Supply Voltage Terminal 30 - Lower Limit Exceeded (00668 - 002).
I read another post where apparently it was the fuel filter that needed to be replaced. I did check the measuring blocks on Control 07, and it did say that Terminal 30 was at 0 amps, while Terminal 15 fluctuated but never went higher than 10 amps.
Is it a bad battery? A loose connection on the battery? Or should I do the fuel filter? Both batteries were replaced in late 2007, so it's not that old.
View 24 Replies
This is concerning my little brothers truck. It is a 2008 4.2 liter with around 55,000 miles on it.
He drove it to work today, and called me this afternoon saying that the truck starts then dies a few seconds later, and the battery light illuminates. He and a coworker checked the battery and connections....cleaned off corrosion on terminals, battery reads 12.xx volts without a load on it, it is the original though.
As of right now he is changing the fuel filter which hasn't been done yet. I also know of issues with the fuel pump driver module. I remember checking the one on my 2005 back when I owned it. As I recall it causes a no start condition, but would it cause a start then stop condition like this? He will check this when he is done with the filter.
Anything else that we can check in a parking lot to try and at least get it home?
View 6 Replies
Simple enough the truck starts then after about 30 seconds it bogs down and dies. I am getting these codes.
705 Transmission Range Sensor Out of Position
708 Transmission Range Sensor Circuit High Input
720 Output Speed Sensor Insufficient Input
743 Torque Converter Clutch Circuit
745 Pressure Control Solenoid Malfunction
1747 Electronic Pressure Control Solenoid A- Short Circuit
Sounds to me like the converter it locked up. What do you think? Its a 5.4L
View 3 Replies
I've got an issue with my 92 2.3 ranger.... sitting at idle for 30 or so seconds it starts to chug and sometimes dies.... I can hit the throttle and its fine for another 30 or so seconds.... while cruising on the freeway after about 30 minutes it starts to cut out badly... let out of throttle for a few seconds and it clears up and drives fine...
Here's the part that has me confused... pulled codes yesterday using a innova scan tool...
koeo were 4, 10, and 538...
koer were 111, 10, 157, 158, 181, 327, 328, and 334....
How does it give me a 111 pass code and then still come up with all the other codes? I am thinking my ecu may be screwed.....
View 4 Replies
