I replace the frond brake pads. Press the piston caliper using a c- clamp. When my brake job is done, start the engine, pump the brake now the yellow light come on.
View 4 RepliesI have about 50,000 miles on my pads, they look 50% gone, but couple days ago I've got short "beep" and light yellow came on(circle with several small parts of larger circle). What and why? Rotors, pads, other?
View 4 RepliesI know on some cars and trucks you need a special tools to push the caliper back in. i just use a large c clamp to do the job. Question do i need any special tools to replace the front brakes pads?
View 7 RepliesI'm gonna replace my front and rear brake pads. Any tips? Do I need to pull the rotor off and clean the axel? I've watched a couple of youtube videos but they leave me with a few answers. I have all the tools, what kinda lubricants will i need? Any recommendations? I hoping I can do a flawless job without and squealing...
View 13 RepliesI just changed brake pads front and rear. My light was on indicating need for such. After changing i figured light would reset and turn off. Not the case. How do i reset the light? Was there something i needed to do to sensor when pads changed?
View 5 RepliesOK, I just got back from having pads and rotors install on my '99 Passat. I was expecting this to clear up the brake and abs light problem but it did not. The brakes still feel mushy and the ABS light still comes on.What should I check? In the brake forum people suggested bleading the brakes, is this the next step? Any quick how to?
View 3 RepliesMy front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 RepliesLooking for instructions on how to replace emergency brake pads on a 2003 F250 2-wheel drive Ford truck?
View 11 RepliesI have a 2001 ranger 3.0 auto 2wd and the abs light is on. this is what i have done so far. I had to replace all the front end joints so i took the front sensors and ohmed them and got continuity and voltage when i ran a metal past them and the same for the rear on the diff. so i figure they are fine. the wires to the frame look ok and i the truck has no damage so i figure the wires are fine.
I checked to see if the fuses are installed after I got the fuse layout and all the fuses are there and good. So I took it to advance auto and it came back with everything bad sensors motor controller and if anything else could be bad with the abs it said it was. I told them it is impossible for all of it to be bad. so it must be the controller. No I'm thinking the controller it the box attached to the abs pump and lines at the power distribution box under the hood.
Can I just remove that box and replace it with little difficulty or will i have parts fly out all over the place if i remove that box from the pump? All the pictures i see the the abs controller don't look the same as the one i have on my abs pump.
Second time my Tiggy is going back - first time I was told to speed up to 50 or 60 MPH and slam on the brakes and that appeared to work for a while, but now, I feel like the neighbors are going to file a noise complaint on my brakes!
There was mention of a TSB - just wanting to see how to be able to get that number and if there was any other solution, minus the replacement of pads as they have plenty of meat on them still.
I took my R to a local mechanic to have my rotors turned and my brake pads replaced (RedStuff). A couple of days later, I noticed a loud noise coming from my front passenger wheel well when I was driving, and the pitch changed when I hit my brakes. It appears that the anti-rattle spring was not reinstalled properly because it has fallen in between my caliper and rotor, causing damage to the rotor and my aftermarket wheels. Since I'm not much of a DIYer, I wanted to get your opinion on the situation and how I should approach things with my mechanic. How hard is it to properly install the anti-rattle spring?
View 7 RepliesI noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 RepliesI'm having issues with very loud screeching noises on my 08 awd. Sounds like a garbage truck. Lexus said its $625 to replace brake pads and rotors to stop the noise. I'm not really a fan of DIY so is that a fair price for the parts and labor or should I bring it somewhere else?
View 14 RepliesA week ago my brakes started squealing badly. This past weekend I pulled off the offending tire to take a look and sure enough the squeeler is riding on the rotor so it looks like I need to replace the brakes at 53,000km.
The rotors look good so I plan to only replace the front pads. While I am working on it, I am going to disassemble and preform the TSB on the rears as they have been neglected lately.
What pad material should I go for, metallic or ceramic? Ideally I would like something that has good performance, yet had a good life span. I occasionally pull a 2500lbs (dry weight) braked tent trailer, but that is not very often.
03 f350 4x4. New front calipers and pads.
Wondering if there's a 'trick' to getting the front brake pads into the caliper . Those damn springs kept popping out. I'd get three of the four ends into place in the pad holes then one would pop out while I'm trying to get the fourth in.
After about a hour of trying every different way that I could think of, another set of hands came by and with four hands holding things in place, it finally did the trick.
Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 RepliesToday as I was adding pressure to my tires I noticed the front brake pads were wearing unevenly. Both outer pads wore the same. More "meat" on the inner section of pads than on the outer, evenly worn, just sort of slanted down as you move out towards the outer rim of the brake disk.
Is this normal? What would cause this? Should I have it looked at? I've never seen anything but even pad wear, perfectly parallel to the brake disk.
Edit for these pictures to clarify.....
Having trouble with front brake pads rattling? About a month ago, I replaced pads - rotors - caliper pins on my 20th GLI. I know these cars ride a bit stiff but it sounds like my front end is about to fall off. All brake parts were torqued to spec - I've gone through all T25/T30 torx front end screws etc and I just can't find the rattle??? This has only started within the last few days. Any other places to check for obvious loose bolts etc?
View 15 RepliesThe front pads on the R shift from one side of the caliper to the other whenever I move from forward to reverse they make a loud "clack". I thought it might be an O.E. pad issue, but I've changed the pads out to EBC's, but still no bueno. The new pads fit snuggly into the calipers and seemed to have solved the problem at first, but about 5k km's in, they're making the same noise.
I have anti-rattle springs installed, but they're not working. Is there supposed to be a pair of shims between the caliper sliders and the pads grooves that the previous owner removed for some reason? I don't think so, because that car only had 25k km on it when I purchased it; but you never know.
Just got out of the dealer they said they recommend front brake change. They quoted me for ~730 just for Rotors/Pads/labor on the front (I am going to shop around).
I tried search Golf R Brakes info prior to posting but alot of the searches are for people buying Golf R brakes for Gti's.
1) Do I need to Replace Both Rotors and Pad at the Same time?
2) Currently Car is still stock and see's no tracks, the most car would see in the next 2 yrs would probably be stg 2+ if that. Would OEM Rotors + OEM pads be sufficient? or should i upgrade pads? Below is listing i found with some different pads options.
[URL]
3) Car is currently a 47.5k miles with oem brakes, should i just replace rears as well? even though dealer did not recommend?
4) SS Brake Lines, should i get them?
Scion TC for Camry SE 2007.
I changed the front brake pads and resurfaced the rotors. After putting everything back together, I took the car to test drive it. The stopping power is fine and there is no squeaking or robbing sounds. However, when I apply the brakes at lower speeds moving forward there is knocking sounds the comes with the tire rotations. What is the reason for this sound?
This is my second time changing the pads and rotors, with the first with no issues. I put grease between the shams and the pads, and I sprayed the rotors with brake cleaner before the installation.