Santa FE SM (2001-06) :: 2005 - Transmission Shifting Poorly And Getting Stuck In Limp Mode Intermittently
Apr 11, 2014
I have a 2005 2.7L Santa Fe that was shifting poorly and getting stuck in limp mode intermittently. I read up on it and found that it was probably an issue with the input/output speed sensors. The codes confirmed my suspicions and I replaced both the input and output sensors. The codes cleared and the tranny shifted like a dream. Unfortunately after 2 days and 100+ miles the car suddenly started down shifting randomly on my way home from work. The CEL came back on and the car went into limp mode. Could the sensor have gone bad again? Or could it be the wiring harness that plugs into one of the sensors? I don't understand why the car would be fine for a few days and then all of a sudden be acting the same way.
View 6 Replies
Advertisement
My wife has a 2006 santa fe 3.5l limited over the winter it started acting up went into limp mode and would only go 20mph so I went and picked up a TP sensor well it went out of limp mode so I never changed the sensor well last month it started doing it again so I changed it out didn't work!!! comes up with 2 codes sometimes p2110 and p2118 but normally its p2110 2 times.
If I hit the break it kinda bogs down and pulsates.i took it to my mechanic since I couldn't figure it out and with advice from a hyundai mech. He changed APS didn't fix it so we changed throttle body with used of course didn't work I checked wires and didn't fined any open circuits what are the chances that i got a bad APS or TPS...
View 3 Replies
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
View 2 Replies
My tranny is stuck in limp mode. I can manually shift it, but it won't shift on it's own. The 'automatic' part of the automatic transimission is definitely not working right.
I searched and checked for the usual suspects, low battery or alternator output (measured over 14v at batt. when on), and the range selector switch. I removed the switch, took it apart, cleaned it up, and reinstalled it. It looked like it was in decent shape inside, although it appeared to have had a bit of oil of some sort that had leaked into it. There was a bit of oil on that side of the tranny, around the gear selector and switch, but not enough to actually drip as I don't have any stains on my driveway where I always park. The only thing I haven't checked is the atf fluid level, as I can't seem to find the my wrench that will take off the fill nut. I'll get that figured out tonight.
The tranny hasn't been taken care of like it should, I've had the fluid replaced two or three times over 100k of ownership, but I'm not sure about the filter. Would the need for a filter and fluid change cause it to go into limp mode? Also, it's not throwing any CEL codes either.
View 14 Replies
So yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 Replies
My wife started up my 2005 GX470 this morning to go to work and drove maybe a half mile before she noticed a problem. So she turned around and drove it back home in limp mode. She put it in park and got out.
Most of the Warning Lights are on ( VSC OFF, VSC TRAC, Anti Skid, Check Engine etc). I tried moving the shift lever but there was some resistance and some grinding noises. And it now seems to be stuck in neutral.
How to diagnose this myself? We only drive this vehicle in the winter, and it was fine the last time we used it.
View 7 Replies
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
View 3 Replies
I'm a little bit stuck here. This happened last night, and the dealer is closed today. I have a 2008 Santa Fe SE. It stalled last night, and when I turned it back on, I got a check engine light, the ESC light, and the AWD transmission light blinking. When I go to accelerate, it will not go passed 2000 RPM, and it is driving very sluggish. Its not knocking, or making any other kind of sounds. The air conditioning does not work, but the fan blows uncooled air. It accelerates extremely slowly, even with the petal mashed.
I plan on taking it in tomorrow, but I'd like to know if there is some way to reset the computer. I tried disconnecting the battery for about 30 minutes, but it didn't work.
View 2 Replies
About a week ago my 2002 santa fe suddenly lacked performance and the check engine light came on . At the same time I noticed the speedometer stopped registering. I later discovered the poor performance was due to the fact that the vehicle was in 3rd gear "limp" mode. The code generated is 1602 "failure to communicate between the ecu and transmission control module". At this point I hoping its just a faulty speed sensor that's causing the problem and not the transmission control module.
Does it indeed sound like a bad speed sensor or does it sound like a faulty TCM or could it be a break in the wires between the ECU and TCM? Also, is it safe to drive the vehicle in limp mode until i replace the part later this week?
View 8 Replies
I have an issue with my 2004 2.7 Santa Fe. I keep getting fault codes P0335 and P1372, the engine then goes into limp mode and is very hard to start.
So far I have replaced the crankshaft position sensor, the MAF sensor, the spark plugs, new ignition coils and leads.
I have traced the wiring and found no shorts, the only thing which does not match the service manual is that I get 5v on the CKPS sensor wire when the ignition is on, it said it should be 0V.
The car can sometimes run for 50+miles with no issues - then stalls with codes P0335 and P1372. I have a feeling its worse when the aircon is on but cant be 100% certain/
View 16 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
I am the proud owner of a 2001 2.7L V6 Santa Fe. His mileage is roughly at 170,000 and I keep up with fluids and minor repairs (except an oil change, oops). Yesterday I was out with my fiance and our German Shepherd, we stopped at a restaurant and while we were inside our dog decided to redecorate the gear shift (PRNDL) with my ice tea. I noticed a problem immediately.
When I started to drive, there on the dash board was the normal "D" with and added "1" as if it were stuck between automatic and sports mode? I attempted to shift it to full sports mode to manually shift; I couldn't get him (the truck) to go above first gear, and nothing happened. I then attempted to fiddle with the gear shift to see if I could some how "knock" it back into automatic but nothing I tried worked.
The truck shifts easily into reverse, there's no abnormal sound coming from the engine, it drives just fine but refuses to go above first gear. I did discover tho that if I shift the engine quickly into neutral while driving and then down shift back to "D", the engine will shift easily but I assume this is not good on my transmission.
D and 1 light are on
Won't shift past first gear
Reverses just fine
Kicking it to neutral then D will shift the engine
Spilled something on the gear shift
I will try to upload a photo of what's going on with my dashboard lights referring to the "D" and "1" light.
View 2 Replies
We've got a new 2010 Santa Fe AWD LTD with about 2800km on it. About once or twice a week, under normal driving, we've noticed very harsh shifts. It seems to be the 2-3 shift and is around 40km/h. Just normal acceleration from a stop sign. And just recently a new issue. It seemed like it got stuck mid-shift...
I was accelerating slowly from a stop and on the 2-3 shift the engine revved up above 3000 as if it was in neutral. I eased off the gas and then it completed the shift. My wife took it into the dealer today, but I'm worried they'll send it back as "unreproducible" as we've only had about 1 problem for every 10 hours of driving. We'll see what they say. As you can imagine, I'm not very impressed that we're having these issues before our first oil change...
Somebody mentioned that maybe there's something sticking in the transmission and it builds up enough pressure and then finally makes the shift. But I'm not a transmission expert by any means...
View 691 Replies
Last night my girlfriend and i were coming home in her Sante Fe and it was driving perfectly fine. The check engine light was on, but it occasionally comes on so i figured it was probably just a sensor.
When we got in the car this morning and i put it in drive (automatic trans) it was in sports mode (i'm assuming because a "1" popped up under the "D")
And now i cant figure out how to just put it into normal drive. We spilled a tiny amount of soda on the shifter last night, maybe 3/4 a cup at the most.
View 2 Replies
A few months ago, my '00 Sentra developed a rough idle but I ignored it because it wasn't too bad, until recently at least. It had been getting progressively worse so I went out and bought some CRC MAF cleaner, which solved the rough idle altogether for about a day. After doing some errands, I started the car but it was now stuck in limp home mode, not matter how much gas I gave it, she wouldn't top 20 MPH and 2.5k revs.
I bought a new MAF, and that made the problem worse: in any drive gears or reverse, when given any gas, the engine would stall and die but when in neutral, I can rev it as high as I want to. I reset the computer and cleaned the new sensor to no avail. After re-installing the old sensor (which was visibly broken, it was missing an entire wire assembly), it will run poorly but will now drive with some quirks, and I don't trust it further than around the block.
My question is: with the new sensor, do I need an ECU reprogram, did I receive a bad sensor, or is there a compound problem? (I've heard with similar issues: bad alternator, bad TPS, bad IAC module, dirty IAC or TPS, clogged fuel filter, bad fuel pump, dirty air filter, among others.)
View 7 Replies
Wife come home the other day after leaving for work with the truck no going past 20KM to 30KM.. After some investigating it seems to be in Limp - In Mode. There was a Check-Engine light & after further investigation found a Vac hose with a leak, repaired this & test drove. Same issue.... then there was a loud hissing sound from the engine area so I investigate & now found the EGR sensor (DPEF pressure sensor ) had blow a hose & fried the sensor.
New sensor was replace along with 2-hoses cleared the engine light but the truck still will not go more then 20KM or 30KM max.. I checked the EGR valve with vac pump & engine stalls or so the valve is good. I have left the neg cable off the batt to try & clear the Limp-In mode without success. Looking for a way to clear the limp-in mode or do I need to clear it with a scan tool?
View 7 Replies
I have a 2005 2.5 vw jetta.
It has 150,000 miles....the cars been working just fine untill DEC of last year. I had the dealer check the transmission fluid and they said it was low....so they flushed and refilled the transmission oil...they didnt see any metal but that didnt fix the problem.....
Now i have the car not shifting correctly ....theres a delay when shifting in all gears but it is intermittent, sometimes it shifts hard and sometimes you can just baby the throttle and it wont shift as hard.....once on the freeway the car runs fine......but when coming to a stop you can feel the downshifting.....
I figured it has something to do with the valve body....my concern is the dealerships have quoted me 2000$ to replace the valve-body....the cars paid for and was wondering if i should just move onto a different jetta or fix this one?
If i fix the valve body will this jetta have the same issue later? Also i do have the vacuum pump leaking engine oil....not much can this be fixed while doing the valve body job???
View 1 Replies
I read another blog on here about stratus not shifting and decided to ask someone about my limp mode problem. A few months ago I was driving uphill when it jerked before it got into limp mode. I thought maybe the hot weather caused it(it was 95 deg). I let it sit overnight. and the next day car was fine. for about 3-4 months. Now it got into limp mode only after it goes through all the gears once only. When i come to a stop it will go into limp again. Got a 0700 and 0760 codes. My speedometer works. tach works. Basically everything works as it should.
I decided to change the ATF and filter, both speed sensors and i get the same old codes after a drive around the block. I then decided to remove the neg terminal overnight. Next day I would have no signal at the data link port. When i removed the key from the ignition my dash lights for the mileage will stay on for another 3-4 seconds before disappearing. I checked the ground wires to the PCM and TCM which are good. Fuses and relays are also good. I even swapped some of them. Still no change. 1997 stratus 2.4 auto...
View 4 Replies
My 2007 Santa Fe was acting up at one time, then stopped doing it, and recently started again. My wife is the primary driver so I'm not always in the vehicle when it happens. When the vehicle is started cold, it will run a short distance then the MIL comes on and it goes to a 5 mph limp mode. After pulling over and shutting the vehicle completely down for a couple of minutes, it will run normally with the MIL still on. However, by the time I get back home to pull the codes, the MIL goes off. I don't remember the exact codes, but when it acted up last time I believe the codes had something to do with the TPS, Pedal Pos Sensor, and one other I can't remember.
View 3 Replies
I have a 2007 Prius and it will be my first car once I get my license. It has a bad traction control computer and is stuck in limp mode. I have a neighbor who has worked on these and will show me how to replace it. Right now I have two questions. I keep coming up with how to disable it not the actual part.
View 1 Replies
I have 1 month left on my AAMCO rebuilt transmission. I took it in a few weeks ago when it went into "limp mode" (Stuck in 1st gear). Eventually, they got an error code of P0730, which I believe is electrical-related. All was pretty good but then today, driving @ high speed on the interstate, I could not get into 4th gear...
View 1 Replies
