Santa FE SM (2001-06) :: Code P0715 - Input Speed Sensor Location?
May 18, 2013
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 Replies
Advertisement
2004 Sport Trac V6. Been having hard shifting and P0715: Input/Turbine Speed Sensor Circuit. Cleared the codes and still returns.
From my searches, readings and looking at the parts diagram. On the newer 5 speeds the sensor is the one on the inside of the tranny. This requires taking the entire tranny apart? Is there an external connector for the sensor that I can check or clean first? Replace this sensor. I know the older ones were mounted on top of the tranny. I think this one is mounted on the inside though.
View 1 Replies
I have a 2001 Santa Fe GLS 4WD, I've had my Auto Transmission Speed Sensor replaced and will have the output speed sensor replaced to have speedometer/odometer and cruise control fixed. While having the first sensor replaced my mechanic noticed the Input Shaft Speed Sensor Connector (the plug on the wiring harness) was cracked. I've been looking everywhere for this connector. I don't want to buy the complete wiring harness because I've heard it is very expensive. I want just the connector. What is the part number of just the connector?
View 2 Replies
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 Replies
My santa fe is throwing a vss code. I was trying to replace it but was not sure exactly where it was. Is it the one right under the air filter box or is that a crankshaft position sensor or some other one?
View 12 Replies
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
View 3 Replies
My brother's 2005 Santa Fe keeps locking up in 3rd gear. I've read around here that the P0715 error code that I have is for an input sensor, but I replaced that and it still doesn't work. I also tried the vehicle speed sensor as well and it didn't work.
I was with someone at AutoZone who pulled up a page here that said no I really needed to replace the transmission control module but I can't find that thread here.
View 2 Replies
My brother and father just finished with all of the small issues after throwing in both a "new" engine into the vehicle and a transmission..both have around 80K miles (chassis has around 180K). There were some issues with codes after both were installed, but then everything was diagnosed and fixed, vehicles codes were gone and vehicle was able to be registered, afterall.
Anyways, now the car threw a P0715 code and has issues with shifting. It appears that the Santa Fe is stuck in a single gear (appears to be a higher gear). The car won't shift properly, especially noticed at higher speeds in a main road. Using tiptronic does not seem to make a difference. After the car sits and is taken around the neighborhood, it seems to drive fine, until it is taken out into a main road...I'm guessing once it heats up?
So, what should be looked into? A sensor? Is it maybe because this "new" used trans was swapped in and all of the trans fluid was replaced with new fluid? What could the issue be? I guesss the car's been a headache but they're trying to get it finished to avoid any further codes/issues.
02' Santa Fe 2.7 FWD
View 3 Replies
So my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
View 10 Replies
Where the vehicle speed sensor is located on the 2007 es350. Reomoved battery and air filter box but just can't find it.
View 1 Replies
I have an 08 avalon w/ 281k miles. NEED to replace the transmission speed sensor (P0500 code thrown). Where is it located on the trans and what is the part #? I'm thinking about servicing the trans while I'm there but looks like a lot of "comments" regarding this transmission and the problems with servicing it!?
View 9 Replies
I went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 Replies
Engine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?
View 5 Replies
My 2001 Hyundai Santa Fe V6 is giving out a P0118 code, and the "freeze-frame" data reports a -40F for the coolant temperature. That doesn't make sense so perhaps the sensor is faulty or perhaps the sensor connector is loose?
I'd like to take a look at the coolant temperature sensor but I cannot find it. I have scoured hmaservice, hyunda-forums but all the various pics are still not clear enough for me to actually find the sensor. I have seen all the online pics from Hyundai but I can't get my head around exactly where the sensor is - the pics are either too zoomed in or so many things have been disconnected for the purposes of taking the picture I can't get my bearings.
View 9 Replies
My mother in laws 2012 Santa Fe had a number of dash lights on (ABS, hill decent, stability control). I put my scanner on it and came up with fault code C1209 which showed up as a faulty right rear wheel speed sensor. I have replaced this module and then cleared the codes.
However, the dash lights still light up and the vehicle continues to throw the same code. I don't work on Hyundai's very often so I am at a bit of a loss.
View 1 Replies
I have an ABS light on. I have crawled under the truck I don't know how many times everything is connected just as it should be. The wires did have to taped up because they burnt into after getting against the exhaust at some point, but I had fixed that awhile ago, I've even tore back into the tape and re-did everything again, nothing gets rid of the ABS light. When this first happened it would go away after I turned the truck off, but would come back after using the brakes a few times, especially harder stops. Then it got to where it just came on and stayed on, and didn't go out no matter what. Thinking my ABS speed sensor went, I bought a brand new motorcraft one from rock auto it fits perfectly in the rear, plug looks good. I can't find NOTHING that would keep this light on. The code is always the same "Rear ABS Center Speed Sensor Input Malfunction", how to get rid of this?
View 1 Replies
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
View 8 Replies
So I am getting a CEL and p0501 (Vehicle Speed Sensor) code and don't quite know how to approach it.
Other forums/posts suggest that I check or replace the input and ouput sensors on the transmission, but from what I understand those are each a unique code, and the p0501 is for a sensor located on the transaxle. Is this the case?
I was under the impression that because my car did not have ABS that I did not have the latter sensor on the transaxle, only the input/output on the transmission. If that is the case, will replacing both eliminate the CEL/p0501?
View 1 Replies
My 2003 Santa Fe 3.5 is in limp mode, you can't change the gears and showing signs of faulty tps sensor, but my mechanic is telling me to change whole electronic throttle system , May be its only the sensor.
View 1 Replies
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 Replies
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
View 3 Replies
