Santa FE SM (2001-06) :: Jerk, Almost Like Sputter When Going Into Second Gear
Feb 23, 2012
I have a 2004 3.5L Santa Fe with about 170k miles on it.
Runs great. I am going to change the timing belt here in the next week or so.
I have started having an issue where going into second gear it will jerk, almost like sputter. Does not do it all the time. Seems like a sensor or computer issue because the rest of the gears shift smooth. And if was a problem with the internals of the transmission I would think it would always do it and never go away.
What the issue could be since I am already going to be digging deep into the vehicle might be worth replacing more parts, what it is.
View 7 Replies
Advertisement
What are the symptoms of a bad CPS. This thing is driving me crazy. Iv'e changed the accelerator, Throttle body, plugs. It runs really sluggish when in gear, sputters.
View 1 Replies
So I replaced my turbo about 2 years ago give or take and maybe 15-20k miles on it since. The last few weeks my car has been running some what weird so i decided to bring it to the shop. The guy thinks its my turbo but its hard for me to believe. Here are the symptoms it was having..
1) Lose of power
2) When I was on the high way i would floor it and it just wouldn't go. It would accelerate after 60 mph and it would almost be at a stand still. A few times it almost lost power completely and i had the pedal to the ground and it was decelerating.
3) When I would drive the car would sputter and jerk like almost it wasn't getting gas.
4) After a overnight where it was shut off, the next day i would go turn it on and it would barely turn over and it would be rough for a few seconds.
5) The exhuast/muffler after accelerating would pop
6) I don't hear my turbo spooling as loud and as much as it use to.
Could this be some sort of sensor or even the fuel pump? I feel that it wouldn't have some of these issues if it was the turbo compared to something else.
View 3 Replies
I have a 2003 ranger with 2.3. I drive it daily but it has started to sputter and jerk. The truck has 94000 on it and I bought it new. It sat for over a year but has been driven every day for the last year. It started a couple months ago but would just do it for a second, now I cant drive it on the highway. I think it might be injectors but how do I know for sure?
View 12 Replies
I have a 2004 santa fe with the 2.7L v6. I was driving and then it started to sputter and then stalled. I tried to restart, but the the engine would crank but no start. I came back to it about half hour later it started up as if there was no problem, and then after a 10 minute ride it stalled and did the same thing.I got it home and scanned it, came up with a couple misfire codes, a crank sensor code, and improper segment timing code ( I never heard of improper segment timing ). Also after fuel fill ups it never wants to start or stay running. I researched the fill up problem and found the purge canister valve to be bad. I haven't changed the purge valve yet, would that have anything to do with the stalling? If the crank sensor was bad, would it start later if it sat for a while. With my experiences when a crank sensor goes bad, the vehicle wont restart at all.
View 2 Replies
I drive a 2004 Santa Fe GLS with the 3.5L. The car has a seldom jerk when at a stop after decelerating, and occasionally it feels like the driveline is binding when backing out of the driveway in a turn. The symptoms are consistent with TSB 04-40-003 (attached). As the TSB directs, I have acquired a 4WD Electronic Control Module (ECM) with the updated design.
The TSB suggests I can just replace the module and expect everything to work. However, I have found information that I should use GDS to reset the transmission adaptive learning. I have also seen mentions of engaging a special setting in GDS if my car has an immobilizer. Obviously, I don't have GDS. Is there anything I need to know or is it really just plug-and-play?
View 11 Replies
My car has three codes P0102 - MAF or VAF Low Circuit Input, P0030 & P0050 which are signaling O2 sensor issues.
Car symptoms are a hiccup type sputter when accelerating for the first few times after starting the vehicle. The RPMs will drop down under 1000rpm and it will come back without taking my foot off the gas. The power comes back faster if I flutter the pedal. The last few times it stalled while taking off.
After the car is warm, it runs better smoother. I'm also noticing slightly poor fuel economy. The exhaust smells rich to me.
I'm wondering if there is a fuse that could cause all three codes? Seems like a power problem? Where is the fuse for these sensors?
Should I replace MAF? Can I use the MAF from a 2004 2.4L engine that's at the junk yard? How to proceed.
View 1 Replies
I have a 2002 Chevy Impala driving it in the city of Chicago. It's recently had the oil changed, and the transmission fluid flushed and filter replaced. This car was mine before I went off to school, and I meticulously maintained it for three years, and then my step sister inherited it. She drove it for two years, and then it sat in the driveway for a year and a half. It's got about 175,000 miles on it.
Problem: Every time I start to accelerate past 25mph and get around 2000rpms, the car starts to give out, sputter and jerk. It starts to drop off right when it should be shifting to second gear. When on the highway, even if I floor the gas peddle, it won't accelerate normally, but instead just crawls slowly to higher speeds.
It will eventually reach the higher speeds, but it takes about 5-10 minutes for it climb up from 25mph. I don't know enough about this level of car trouble to make a diagnosis myself, and would like an estimate of the cost for repairs. Also the car is getting around 19mpg on the highway, which I need to improve if I'm going to survive the $4.50/gal of Chicago gas. I'm hoping that fixing this problem will take care of that as well.
View 3 Replies
Its not my car but my sister in laws. She stopped by our house tonight to pick up her kids and when she put the car in drive it showed both drive and 2nd gear. we tried disconnecting the battery so she could at least get it home (3 min away) but it didn't change anything.
She left with it still in 2nd thinking she could make the short drive without any problems but half way home it shifted down to first and it wasn't even driveable. Everything i have read on the web (which was not really specific to the santa fe) was say that its stuck in safe mode. What could have cause the problem? So far no check engine light has come on.
View 2 Replies
ok, I had quite bit of work done, prob over yr ago All oem parts, timing belt, crank sensor, idler pulley, some other things while in that area. So when he was done I got this vibration when it goes into gear never in park only in rev. or drive but only in cold weather and after it warmed up it was go away. No Trans service was done. He kept it overnight outside, had the timing cover off rolled it in the garage, started it and seen that the belt was flapping crazy. So he thought it was that. well every cold morning I have to wait till it is warm to not hear that sound. it only happens during cold mornings never in summer. He had back in his shop 3 times after parts were installed. and its to this day isn't the same. its unfortunate that I didn't have many cold mornings when he had worked on it. but after I had it and the next cold morning it was there.
View 7 Replies
2003 Santa Fe 41,000 stuck in first gear.
View 1 Replies
When cranking, i have to give it gas and rev it til it smooths out. Eventually it will run smoothly. When i throw it in gear, it wants to sputter and die out. If I put in D, i have to give it gas or it dies, but I can only barely touch the gas or it dies out. There is a vacuum leak in brake booster, but ive been told the headgasket could be blown.I want to know if the head gasket could be a problem and if its worth replacing the booster.
View 2 Replies
Two times in the last month my 2003 Sante Fe would not start - the radio, air conditioning will come on but nothing from the engine - not even a click - no check engine light. Had it towed both times - as soon as it was towed it would start up. It seems to happen in 2 week intervals. Now I realize bc they had it in neutral to get on the truck that is what required to start. It hasn't happened in a week but I know it will again.
View 3 Replies
I have Santa Fe 2002 v6 2.7 and it's have been in the mechanic for 2 months now.
Suddenly my gear box don't go up 3rd, the error that the diagnostic reader is P 1528. What it can be? How to Fix it?
View 2 Replies
2003 Santa Fe, 2.7L V6
When placed into Drive, the transaxle (and indicator lights) behave as though the gear selector was in the manual gate and at 1st gear. It seems that no matter what I do (wiggle the selector, disconnect the battery, etc) will bring it out of 1st gear while in D. This issue first occurred about a month ago and it somehow corrected itself. I had hoped that it was a fluke, but it is happening again. Initially, I suspected that it might be a switch or something within the gear selector lever housing in the console, but I've done a bit of searching the webs and it looks like it may be more of a sensor(s) issue.
View 8 Replies
I've been having ongoing issue with lack of power uphill in my 2005 2.7L Auto and noticed during recent freeway driving that when its in cruise mode the car will shift down through 3rd then into 2nd to maintain cruising speed on a steep-ish slope.
That was with adult driver me and two kids in the car so no extreme load involved.
Does car needs to be in such a low gear at 110kmh/70 mph to cope with a slope?
View 6 Replies
My Santa Fe 2001 model V6 4X4 Automatic shift gears down hard from 3rd in to 2nd. I checked transmission oil and its light brown. Should I drain and refill or not worth it.
View 7 Replies
The shifter will not usually stay in 5th gear for very long. The clutch and flywheel were replaced a few weeks ago just before i purchased the car but this problem has only cropped up in the last week. Could it be shifter linkage adjustment?
View 3 Replies
I have an 01 and 02 santa f. I took the v6 out of 01-and put in the 02.put new gaskets on engine new timing belt etc. Got engine in and runs like a champ. But the tranny which looks new I assume its been replaced. It starts out in 2 or 3 all the time want shift into od. Reverse works. So I found one plug dangling I couldn't figure out where it went then i found it. It plugged up on top of tranny. Well now it starts out in first and shifts through all the gears. Drove it down the rd shifted fine. Turned around and put in reverse then when i went to drive it jerked real hard. Shifted out fine so I went to floor it to make it kick down and it jerked again. This time it was hung in 3 or drive cause when I pulled into my driveway it was in high gear and u can put it in manual mode and the light only goes to second and d when it acts up like this. So i killed the car started back up and know it will go into first in manual mode and shift out and do fine?
View 3 Replies
I recently started having problems with my 98 GMC Sierra c1500. I'll be driving and all the sudden it will jerk as if it's shifted from 5th to 1st gear, but the revs don't go up, they drop to about 600 like it is about to die and then it go back to normal revs. It only does this while I'm on the gas and very rarely at idle. I don't know if it could be the transmission or something is blocking fuel from the engine.
View 5 Replies
So yesterday my car was running as fine as it always has. Then today came around...Car started fine, shifted into first and second fine, but when I hit 3rd it started to sputter in the low rpm's. Around 3000 it picks up a bit. This then continued happening through all of the gears. I noticed that the engine light was flashing for a few seconds and then went away completely. It still putters, struggles, and shakes when accelerating in the low rpms but its not throwing any codes. I know there are a few things it could be i.e. vacuum pump, bad coils or plugs, are maybe something more serious (fuel pump maybe?). I'm at a loss, especially since the car is throwing no codes (so there is nothing to scan for). I was hoping vortex could give me somewhere to start on this, I don't have a VAGcom so getting it scanned means $$$ and I want to get a start on the problem before I go that route. Here's some basic info:
Its at 182,XXX miles. Its never thrown any engine light or cel code in the 2 years 40,000+ miles i've owned it. I run 0w 40 eurpean car formula oil through it every 3-5k. I run seafoam through it every 6 months. I'm NOT sure when the last time the coils have been replaced.
View 3 Replies
