Sierra :: 2008 GMC - How To Remove Brake Pads And Rotors
Jul 13, 2011
How to remove the front brakes pads and rotors on my GMC Sierra 2008 - 1500 - crew cab - 4X4.
View 2 Replies
Jul 13, 2011
Advertisement
Ford F-150 (2004-2008) :: Remove Rear Brake Rotors?
I'm having a hard time trying to remove one of my rear brake rotors.
I thought these simply pull straight out and off, but mine might be rusted in place. I soaked the front facing area around the axle with Kroil and then tried jolting it out by tapping it with a rubber mallet. No success
What's the trick?
Accent LC (2000-05) :: How To Remove Caliper To Replace Pads And Rotors
I need to replace the rotors and calipers on my 04 accent gl. I noticed there are 5 bolts on the back of the caliper. I know one is for the flex hose connection. Then there are 2 big hex bolts closest to the dust plate. Are those for the caliper mounting bracket? and if so will they need to be removed? Then the final two are on the outer edge, however the top one is rounded and rusted, is this normal? The one on the bottom is a hex. So what needs to be removed to change the rotors and pads? I also notice that there are two screw holes in the rotor, that I guess snug it in place against the hub, however the screws are missing. Is this bad? are they needed? and if so can I get new ones?
View 10 RepliesPrius (2004-09) :: 3 Brake Dash Warning Lights Came On After Got New Brake Pads / Rotors
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 RepliesLexus IS 2014+ :: Front Brake Pads Touching The Rotors / E-Brake Engaged And In Park
I noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 RepliesPassat (B7) :: Rear Brake Pads And Rotors Went Shot
So my car has 36 or so thousands miles and well the rear brake pads and rotors were SHOT! The rear rotor was falling apart and huge chunks were coming off. The issue stands now that I can't spread the rear caliper for anything, the ebrake is off too. I tried to use the C-Clamp trick but it honestly didn't even budge. I also opened up the bleeder and master cylinders cap just to cross that off the list when trying to compress. This is the hardest caliper I've ever had the misfortune of dealing with and I fear that the passenger side is not going to be any better. Aside from spending more money or renting the "tool" is there anything else to check because the C-Clamp trick has work on mine and my father trucks calipers.
View 3 RepliesLexus RC 2015+ :: Ceramic Brake Pads With Stock Rotors?
I'm getting sick of having my rims getting dirty after one hour of driving because of all the brake dust that the OEM pads give off. I keep hearing from shops that ceramic brake pads are not only more quiet but will put out much less brake dust. On the other hand, Lexus is telling me that if I do that, I will forsure damage the rotors but I really feel like they just want me to keep the car stock which is why they're saying that.
Are ceramic brake pads a bad idea with stock rotors?
Passat (B5) :: 1999 - ABS And Brake Light After Replacement Of Pads And Rotors?
OK, I just got back from having pads and rotors install on my '99 Passat. I was expecting this to clear up the brake and abs light problem but it did not. The brakes still feel mushy and the ABS light still comes on.What should I check? In the brake forum people suggested bleading the brakes, is this the next step? Any quick how to?
View 3 RepliesGolf IV R32 :: Jerking And Brake Pads Sticking To The Rotors When Turn Left And Right Going Slowly
Here is the problem. When I reversed the car out of the driveway i noticed it would not reverse freely. It felt as though something was blocking the car (as though the handbrake was still on).. When i turn left and right going slowly it feels like the car is jerking and the brake pads are sticking to the rotors.. Its the same when i reverse but I only feel it when im going slowly and the sound gets louder when turning left or right...
I checked all my break pads and rotors.. Im thinking it could be something with the haldex system... Hope not.. My haldex fluid was changed at 80k and im at 88k now..
Ford F-150 (2004-2008) :: 2005 - Brakes Shimmy After New Pads And Rotors
Brakes shimmy on my 05 f150. Been doing this since new new pads and rotors and alignment. what now?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Clunking In Front Brakes After Replacing Brake Pads And Turning Rotors
Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 RepliesFord Excursion :: Rotors Rubbing On Caliper Bracket - Brake Rotors Too Thick?
I replaced my warped front brake rotors a couple thousand miles ago and all was fine but when I went to swap over to my snow tires, I can see that the outer part of the rotor has been rubbing on the caliper bracket. This is happening on both front rotors. Could my new rotors be too thick or something?
View 4 RepliesPassat (B6) :: Front Pads And Rotors Went Shot
I've had a 2006 Passat 4Motion for about 15 Months now and it just went in for it's 20k mile service. The dealer told me that the front pads and rotors were shot, and the rear pads needed to be replaced.
I've read that the front brakes are rather easy to change but my question is: are there any aftermarket pads and/or rotors that last longer than the OEM ones? I just don't think I want to do brakes every 20k miles. Now in regards to the rear brakes, apparently my rotors are okay but my pads need to be replaced. I've read that you need the VW "Vag Com" to do that and I'm new to VW software stuff.
Passat (B5) :: 2003 - Changing Rotors And Pads
On 8/18/04 VW told me that my 03' Passat (38'000 miles) needed new rotors & pads. I bought the car new. They told me that VW used rear pads that eroded quickly and provided new rotors on the house. I decided not to press my luck and paid for new pads. I look at my pads now through the rims and it seems dangerously thin and the edge of rotors has gouge all the way around. HAS ENOUGH TIME PASSED FOR A LEGIT REPLACEMENT ON THESE PARTS?
View 4 RepliesIS F (2008-2014) :: While Washing Rusty Drippings From Brake Rotors
It's happened the last two times I've washed the car. I thoroughly cleaned the wheels with Sonax followed by soapy water, then washed the rest of the car. After washing, my usual routine is an initial towel dry, then I take the car for a short drive to shake the excess water out of crevices & the wheels, followed by the final towel dry & detailing.
This is happening on all four wheels. I know my front rotors are nearing their end of life, but the rears should have plenty of life in them (45K miles).
Chrysler - Pacifica :: Shudders When Braking After New Rotors And Pads
My 2004 Pacifica (130k miles) was left parked for 2 weeks while we were away. Upon return it didn't wqnt to back out of the parking spot. After about 1/2 revolution the wheels made a clanking sound and hung up. Rolling back and forth freed things up enough to drive the car to the mechanic (about 40 miles). And after the first mile or so everything seemed to go back to normal, with no absolutely signs of anything not wanting to turn smoothly.. The mechanic thought that the problem had been that the brakes were sticking due to the car being unused and said nothing needed to be done. However, upon examination he found that we could use new front brakes and 2 motor mounts. He said that the need for brakes and motor mounts was due to normal wear and tear, and was not related to the wheels hanging up issue.
But now, immediately after installation of 2 new front rotors and pads and 2 new motor mounts there is a vibration/shudder when braking from anything more than 20-30 mph, which was never there before. The shudder is rapid and sometimes pronounced like going over the warning groves cut into the edges of pavement on the interstate. He thinks that this may be a sign that there is a driveshaft issue, and dismisses it as due to an out of round rotor since they are new. I don't know what to think. By the way, he has always been an excellent mechanic, with a great reputation and loyal following.
Camry :: Rotors / Pads (new) - Low Medium Squeaking Sound From Brakes
I recently had rotors and brake pads replaced on my 2007 Camry (front pads/rotors and read pads/rotors).
It was done last week and she is braking fine. But sometimes now when I brake there's a low-medium squeaking sound from the brakes. Is this normal / what's the likely cause?
BMW - 328 :: Changed Front Pads / Rotors - Steering Wheel Shimmy
Have a 2009 BMW 328i with 78,000 miles. In the last year, the front brake pads and rotors have been replaced by the dealer 3 times, each time because of "warping" which is their diagnosis of a steering wheel shimmy (left to right oscillation) that occurs under light to moderate braking, especially at highway speeds.
The strange part: replacing the rotors and pads seems to solve the issue, but only for a few hundred miles.
I am led to conclude that something is causing very accelerated uneven deposition of pad material to the rotors - but what could it be? Suspension components and bushings have been inspected and check out. So do calipers. Recently completed: four wheel alignment, wheel rounding and balancing did not solve the issue. One dealer will no longer look at problem until "all four tires replaced" - but tires look fine, they are OEM RFTs with about 4/32nd's of tread left. Car seems fine cruising on highway - steering wheel shimmy only occurs under braking.
Lexus LS 2007+ :: Brakes Shudder After Changing Pads And Machining Rotors
2008 LS600hl with 31K miles, been having low speed brakes shudder for quite sometime even after changing pads and machining rotors. This weekend thought about putting grease on the pins holding the pads, this did the trick, shudder is gone!
View 9 RepliesCivic - Honda :: 2005, Car Is Pulsing Badly After Replaced Pads And Rotors
I replaced the pads and rotors on my 05 Civic 3000 miles ago. Now it is pulsing badly again when stepping on the brakes. I can feel the pulse in the brake pedal and the steering wheel. What should I be looking for when I pull off the wheels again.
View 8 RepliesFord F-150 (2009-2014) :: 2011 - Replaced Rotors But Pads Still Shaking
I've got a 2011 XLT. The front rotors have been turned twice already in 39k miles. Once at 12k and again around 24k covered under warranty. It starting having vibrations on the highway and shuddering when braking again around 36k. Tired of dealing with the OEM rotors and told it would no longer be covered under warranty I went to Autozone and got duralast rotors and pads for the front.
Swapped them out Friday
- took caliper off
- removed pads
- took caliper bracket off
- swapped rotor
- opened bleed valve to push back piston(used a vise/c clamp combo)
- closed valve with piston under pressure
- put in new pads
- placed caliper bracket back on
I did not remove the pins, they seemed to slide fine and the remaining hardware still looks fairly new.
Took it out all was good, bedded the brakes a bit and called it a night. Come out this morning and start to head out and it's shaking like crazy now once above 40 mph. Made it back this afternoon and took the passenger side off and its not making full contact with the rotors. I've read this can be common until the pads are broken in. Driver side appears fine, pads appear to be bedding fine and nothing looks out of the ordinary, I took the caliper back off but had to open the bleed valve to get it loose enough to let go of the pads.
I've even taken the passenger side back off and reset the piston again just to make sure.
Put everything back together and take it for a spin. Truck seems worse now even at slow speeds 25-50mph. Once the brakes start getting hot from stopping the shaking goes away. When the brakes start cooling back down it comes right back.
Going to swap back the OEM rotors and retest in the morning. Will take the new ones back If that puts it back to normal I may just replace with OEM ones then. The brakes work perfect it's just the shaking that I can't seem to figure out.
Anything to check? It seems like the new rotors are warped