My '99 Suburban 350 with the autotrac 4wd is having electrical problems. The transfer case fuse always blows. I thought it may be the transfer case shift motor, so I took it out and tried and the fuse still blew. I tested the pins on the fuse, and sure enough they are shorted together, but only when the car turns on.
View 14 RepliesI have a 2002 GTI 1.8T with the AWP engine and tiptronic. There is a fuse in the picture below that blows as soon as the car is started. It is located next to the brake booster on the firewall. It does not blow when the ignition is turned on, just when the engine actually starts. I'm not throwing a check engine light, pulling a scanner code or noticing any of my electronics not working. I took a 20 AMP fuse out and replaced with another 20.....and have since blown 5 of them trying to diagnose the problem.
View 10 RepliesI purchased a 98 dodge ram 4x4 v8 with automatic transmission. When I purchased it the guy told me there was an issue with the transfer case. From what he told me he got stuck and the transfer case is the result. I was told there is a fork in the transfer case that is probably bent? Does this sound correct? It is currently in 2wd. Do I have to remove the transfer case to replace the fork? What is it like to remove the transfer case? Drop the tranny?
View 16 RepliesLooking at another Ex but the owner says the transfer case does not engage. Says it can be locked into 4X4 by crawling under it and engaging it manually by removing a motor [Servo motor ?] Does this mean I would need a new transfer case or just the servo motor ? I know mine did the same thing last winter. It would go into 4X4 and then pop out.
View 10 RepliesI just replaced the transfer case BW 4405. And I noticed that the 2 sensors (front drive shaft and rear drive shaft) are bad. What is the name of these two sensors? I'm looking for a brand new ones...
View 13 RepliesI own a 2006 mazdaspeed 6 with 90k+ miles, 2 weeks ago I had a 90k service done at the dealership. On the 14th of May, the 90k service was done (which includes the changing the transfer case fluid/oil). Car was not driven every day, but on the 23rd of May the car made horrible noises on the way home from work. I called a flat bed/tow truck, and have tried to lock in the problem. The sound seems to be coming from the transfer case.The question is could they have done something wrong or was it just the transfer case’s time to go up?
View 19 RepliesTook it in for the 10K service and squeak that started coming from under the treg. The said it needs a new transfer case.
View 12 RepliesWhere/how to check the ATF in the transfer case? I found the lower drain bolt,but I don't see anything up higher that looks like a fill hole.
'91 Aerostar 4.0L AWD
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 RepliesSwapped out my transfer case since mine was detonated and now my tranny is running hotter? Drove in town for about 10-15 minutes and noticed my temps climbing and once it got to 180 it felt like it was slipping when moving from a full stop. i went home and parked it. Checked my fluid level and it looked a little low so topped it off while running and went through gears to make sure it was good. Drove again and it still went up to 180 in 10-15 minutes in town driving. Before we swapped the transfer case it was driving fine and went on a road trip 6 hour drive and felt fine. I bought the excursion and it supposedly had a new tranny in it.
View 14 RepliesSo long story short I have a 92 Aerostar AWD which I'm pretty sure had the transfer case recall done (97V204000 1992 FORD AEROSTAR Recalls) it has the aluminum driveshaft but a couple of years ago the transfer case cracked and I replaced it with a "New OEM" transfer case off eBay. Fast forward to the present and my van has a strong vibration at 60+ my transmission guy says it all looks good so the vibration has to be from one of the driveshafts. My thought is that I may have got a transfer case without the recall done on it and its warped my driveshaft. I don't really know thats possible or what I could do about it if that was the case.
View 8 RepliesI bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 RepliesAbout 9 months ago heard a strange noise when shifted into 4 wd , sounded like driving over those grooves on the side of the highway to keep people awake.
Had to pull over to stop , as it would not go back into 2wd with the noise still going.
Then it stopped , after shutting truck off and restarting.
Then earlier this year after trying to do it again in 4wd had bad clunking noise and was hard to get back in 2wd , I can here the shift motor engaging and the dash reads in 4wd, seems its not engaging fully in 4wd and not going back to 2wd, its a very bad clunking noise, shakes the whole truck.
The dang thing leaks from the fill plug, I been reading about using liquid teflon on it.
View 4 RepliesI had sold my Explorers but just picked up a 2000 Excursion V10 plow truck. It has been hacked and slashed I find cut wires under the dash and hood. I have tried everything to get the 4x4 to engage and no luck. It is used just for my driveway no road driving...
So question is: Can I engage the 4x4 at the transfer case so it will go, and stay in 4 wheel drive. If so do I take the shift motor off or does that big bolt by the motor do anything.
I keep getting a check engine wrench on the readout, put a scanner on it and got the following code:
P183b transfer case code ...
What this means?
My 4WD sport trac was running fine. I took it off road and put it in 4WD. After I was done in the woods. I put it back into 2WD and backed up to unlock. I then drove 2 hours home. The next day the transmission started shifting funny, especially overdrive almost like I was low on fluid. (which I check and I'm not) And the truck sounds like its running ruff. Is my transfer case still ingaged? Do I need to take it in for tranny work?
View 9 Replies I have a BW 1345 transfer case. Does it have the shift in the fly capability? And, if so, what precautions should be taken if shifting on the fly?
Second, where can I get a "plate" or label that shows the shift pattern? I know the shift pattern, I just want to post it in my vehicle in case anyone else ever drives it and needs to use the 4 wheel drive.
It has a floor shifter for the xfer case with 2wd, 4wd-H,and 4wd-L, and Neutral positions. It works fine in the 2wd and the 4wd-H positions. The problem is it sometimes slips out of 4wd-L position into 4wd-Neutral, which I have just lived with, but it is annoying. I think I heard this is a known problem with these 1970's Ford xfer cases, and the fix involves removing the xfer case and replacing a part.
View 10 Replies80K miles on this truck. pushbutton 4wd controls. Operates normally in Auto 4wd, 4Hi, and 4Lo, and 4wd functions as it should. By that I mean that the front wheel driveline is engaged in 4Hi & 4Lo, and engages under hard acceleration or rear-wheel slip in 4wd Auto. Here's the problem: when I push the 2Hi button, it shifts into 2wd as it should whether moving or stationary. However, when I take the rig up to road speed in 2wd, it operates fine for a minute or two, but after I've slowed or stopped, it won't move, and acts as if the transfer case has shifted into neutral. At times, it will move forward, but not in reverse for a short time before going neutral. Push the 4wd Auto button, and it goes back to working as it should in that mode. Transfer case is full of clean oil, wiring harness at transfer case (including ground) has been disassembled and inspected carefully. No codes nor "Service 4wd" messages are displayed. There is no clunking or grinding, and the actuator motor sounds as if it is working when the buttons are pushed with ignition on and engine not running. I have been unable to locate any fuse or fuses which might be associated with the transfer case or 4wd system.I'm stumped.
View 13 RepliesThe Touareg has been a great family car for last 6 years, no issues with it at all until a few months ago, when the hanger bearing or drive chaft bearing went out with only 45k miles. No loger under warranty so $500 later and all was back to normal, until last week when the car started developing a humming noise above 40 mph. Had the local shop look into it, they put the car on the lift with it in gear and seems the noise is coming from the transfer case, i search the site and i have a few questions. Is there a recall on the transfer case?
How much should i expect to pay for a new transfer case? Is this a known problem with these cars like the drive shaft bearing? Car is a 06 with a 6 cyl, still under 50k milles im not sure if i should get it fixed or trade it for a new car