Chrysler - Ptcruiser :: 2006 - Gauges Drop - Stop Working - Power Loss
Oct 25, 2013
2006 Chrysler PT Cruiser. While driving, it seems at random, all gauges drop and stop working, no gas getting to the car, power loss. Sometimes lasts a split second, sometimes lasts up to 30 seconds. The car will even stall here and there, but usually not. Usually, power gets restored. But sometimes the car won't even start for an extended period of time. Of course, when the mechanic takes it for a ride it does nothing wrong.
View 2 Replies
Advertisement
I have 2006 Pt. Cruiser Touring with 150,000 miles on it. It has been well cared for with oil changes, tire rotations, tune ups, and preventative maintenance done regularly.
My problem is this. Sometimes when I drive the vehicle, all the warning lights on the dash board will light up, and all the gauges go dead. But the car keeps running and does not decelerate or lose power. The lights shut off within 3-6 seconds, with the seat belt lights being the last to go out. I have paid over $600 dollars for 6 hook ups to the computer at the dealer with no codes showing.
I have just replaced the belts, cam & crank sensors, spark plugs, spark plug wires, battery, alternator, hoses, water pump, timing belt, and it still does this. This morning when driving to an appointment, it did this again 3 times within 5 minutes. I had activated the cruise control when it did this. When I turned the cruise control off, it did not do it again. But in the past, this has happened when I was not using the cruise control. And it happens at all speeds, 60, 20, 35, or 40 MPH. What is wrong with my car.
View 19 Replies
Last weekend we had our first warm weather up here in the Finger Lakes. My girlfriend wanted to be able to put down the top on her 2005 PT Cruiser convertible, but for a few months now the power windows and power top have not been working. She was going to take it to the shop, but I said, it may just be a fuse. I looked up the owners manual online, then drove the car to an auto parts shop and replaced the circuit breaker in the fusebox under the steering column, because it controls the power windows. The two passenger side windows started working but not the others. So I bought a fuse tester and tested all the fuses in the dashboard fusebox. They were all fine.
I drove the car some more, and couldn't figure out why the other windows wouldn't work. At one point I stopped but forgot to turn the engine off. I pulled some of the fuses out and plugged them back in, one by one. When I pulled one of them out, the engine stopped. I thought "uh-oh," then turned the ignition key to off and replaced the fuse. When I started the car again the engine light was on. I drove home (about 12 miles). I looked up stuff about the engine light on line and learned that after three trips, if everything is okay, the engine light will go out. That is exactly what happened. So I thought everything was okay except that I hadn't solved the window problem.
Two or three days later, my girlfriend got in the car to go to work in the morning. The car started but the engine light was on, and as she backed up out of her driveway the engine stopped. It wouldn't start again. The starter would just make a ratchety sound. We both figured my experiment with the fuses must have done something. I took the car (by tow truck) to a mechanic, and he didn't see how the fuses could be the problem. It turned out that the starter was bad and had burned out the battery. So I paid to have the starter replaced and a new battery put in. But when we picked the car up, he said what I'd done had nothing to do with the problem. He said the starter had probably been bad for some time, and it was just a coincidence that the car broke down a couple of days after I fiddled with the fuses. Now I'm convinced he's right, and my girlfriend is just convinced that he's wrong.
View 15 Replies
My dash board lights up for no reason. All the lights -- seat belt, engine, oil, etc. Also the speedometer goes from 0 to 100, the RMP needle goes from 0 to whatever and my gas tank need goes from empty to full to back to empty. In addition it is now loosing power --no gas is getting where ever so I must pump gas peddle to get it going again. It usually lasts only seconds and there is NO rhyme or reason to when it does it. I left it with a dealership and they drove it 265 miles and it did nothing. I got it back and within 48 hours it started doing it again. They did put in a new instrument cluster and it still continues.
View 3 Replies
My '06 Pt Cruiser A/C works fine @ speed, but idling and @ stop lights it blows moist warmish air and idles roughly.
View 7 Replies
Recently my PT Cruiser was having trouble shifting into park so the car could not be started or the key could not be removed. I had to force it into park a few times and then something popped and broke. The car thinks it's in drive so it will no longer crank. I took a look under the hood and the shifter cable looks to be fine and connected properly but what I found under the center console seems to be the problem. The entire cable and plastic mechanism move freely. To me it seems as if the plastic piece holding the cable aligned is quite stuck. The metal rod looks like it's supposed to move inside the casing? Here are some photos of what we're dealing with.
View 5 Replies
My 2005 PT Cruiser Limited 2.4 Turbo bucks under acceleration and had displayed the codes for a bad Map Sensor, Throttle Positioning Sensor, and Oxygen Sensor. I replaced both Oxygen Sensors, Map Sensor and the TPS. Each time I replaced a sensor and took it out for a test drive it ran great. The next day my wife is on her way to work and I am on the phone with her, she accelerates to get on the freeway and the bucking is back. The codes it displays now are P2074, P1697 & P0038. All the previous codes except P0038 disappeared when I disconnected the ground cable for 15 minutes after the repair. I start the car every morning for her and run the heater for 15 minutes as it is in the 30's here in the morning and so I replicate that before I take it on a test drive after completing a repair so the conditions are the same.
View 1 Replies
I have a 2006 PT Cruiser with approximately 94K miles on it. This year I started a 2-hr round trip commute every week day, so the car went from getting ~200 mi. a week on it to ~700 mi. a week. I bought it used ~4 years ago with 28K mi. on it.
2 months ago, the car started shaking between the speeds of 50 and 60 mph. Not sure how to best describe it - kind of a shake/jerk, like someone was jerking the car forward very quickly and repeatedly. It seemed to be strongest in the front of the car on the passenger side, although you could feel it throughout the car. I took it to a repair shop. They balanced the tires, but that only very mildly worked. Then they changed the front axles (said there was a lot of play in them). They replaced the brakes, rotors, and timing belt at as well, for unrelated reasons. With new front axles, the shake disappeared, but the car has been idling incredibly rough ever since I got it back. You can see the steering wheel vibrate and feel it in the seat when I start the car or am stopped with it running. This never used to happen.
Additionally, the shake has now returned, but from the driver's side of the front of the car now. Again, it's between 50 and 60 mph, although it's slowly creeping up into the 60-65 range also. It's stronger if I'm pushing the gas down more, like when going up a steep hill. If I'm going downhill at 50-60mph, I don't notice it or barely notice it. On flat ground it's noticeable, uphill it's becoming severe.
View 3 Replies
We have a 2006 PT Cruiser. Within a year the Dodge dealer has replaced the heater core five times. They say it's a defective part each time, but I'm not so sure. Usually the core gets a leak after the car has been driven, then parked for a few minutes. When we restart it the heater core blows sending antifreeze vapor out the heater vents.
View 2 Replies
My check engine light goes on ONLY when my husband starts the car.He is starting it normally.Then all the controls read incorrect such as temperature and RPMs.When I get back in my car later , I start it and it goes off! Why this is happening or what he might be doing?
View 8 Replies
My 2006 PT Cruiser Touring Edition has a lot of squeaks from the front. Most noticeable at low speed going over speed bumps or potholes. My mechanic has checked front end and says noise is coming from rear cradle bushings and wants to drop rear cradle and inspect/lube bushings. Also says sway links are dry and recommends lubing these as well. Everything else is OK. Estimate is $100-$150. Other than the annoying squeaking (which I can live with) is there any other reason (safety/mechanical) to get this done?
View 2 Replies
I have 2006 PT Cruiser Turbo Convertible that violently shakes when I am stopped at idle in gear and the A?C compressor is on. When I turn the A/C compressor off (leaving the fan on) there is a drastic reduction in the vibration. If I put it in park and turn the fan off, there is an additional lessening of the vibration.
I have taken it to three different mechanics and had the following done: spark plugs and spark plug wires changed, fuel injection system cleaned, the 'whatchamacallit' in the fuel system cleaned out, the two main motor mounts changed.
None of the above maintenance has lessened the vibration one bit. Question: What is causing it?
View 6 Replies
I drove the car to town this morning, and then to work without problems. I go to get in the car and the car has no electrical power what so ever. I am going to check the voltage and battery terminals, but is there a fuse that sends power to everything in the car, including lights, horn, etc? There is NO power at all.
View 5 Replies
So over the last few months I have been having more and more idling and power loss issues with my 2006 V6. When idling she intermittently will try to stall and the rpms will drop below 500 and then spike back up. A large percentage of the time I hear a loud whining sound while driving down the road and I notice that turning off the air conditioner will remove the sound at times.
***what I have done so far**
Idler Pulley
Belt tensioner
sepentine belt
cleaned MAF
Cleaned Throttle body
Throttle Position Sensor
Had car reprogrammed
So I pulled the belt off and checked all the pulleys and did notice some grittiness in the AC pulley (inner) and was wondering if this might be the issue. Attached is a video I uploaded, Video .....
View 7 Replies
I have a 2006 town and country with a 3.3 and 220,000 miles.
Last week I was having some hard starts and loss of power on acceleration. My check engine light flashed during one episode so I had autozone check the code and it showed a misfire. I changed out my plugs and wires and that solved my issue. It started and ran like new.
Yesterday, I was running errands and my charging light came on. I was about ten miles from home and I decided to go for it. It was night so the headlights were on. Along the way, everything started to dim. Headlights, dash lights, airbag indicator came on and then the van just died. I walked the final mile and we towed it home.
The alternator and battery were both replaced last year in November making them both one year old. AC Delco battery 660 cca and I had a very reputable alternator shop rebuild the alternator.
So before I towed the van home, I hooked up some heavy duty jumper cables from a running chevy venture and let it charge 15 minutes. After the 15 minutes it was just clicks in rapid succession.
I hooked it up to a trickle charger overnight, 12v 2 amp setting. This morning, the van started, idled fine for about five seconds and then started trying to cut out. I kept it running by giving it gas but after about twenty seconds it stalled. I tried to restart and nothing but the rapid clicks. Three more hours on the trickle charger and the same exact thing happened. It started, began to stall, quit and then wouldn't restart.
I noticed today that the power steering reservoir was leaking a decent amount of fluid down onto everything around it including the coil pack. I replaced this today and used brake cleaner to clean all the surrounding components.
After doing some internet sleuthing, I found a thread with the same problem. For this guy, he had a disconnected ground from the negative battery terminal. I chased mine down (G101) disconnected and wire brushed it all clean. Put it all back together and still the same problem.
Here is what I have discovered:
Trying to jump it from another vehicle only results in the clicks. This is true whether the jumper cables on the dead battery are on both terminals or the negative is grounded on the motor. If the battery were the problem, I should be able to jump through it. If the alternator were the problem, I should be able to start with a jump.
After charging the battery, it will start once but then die soon after. Battery with the key off will read just under 12 volts (11.9, 11.6). With the key on, it will drop to the 8's (8.6, etc.) I have not yet had the battery or alternator bench tested. I plan to start with the battery in the morning.
It seems to me that the alternator wasn't charging the battery or it wouldn't have just killed the battery as those accessories should be powered by the alternator. It shouldn't be a starter issue since it will start after being on the trickle charger.
View 6 Replies
2003 PT Cruiser won't start immediately after short trip with a short stop. Always does start after turning the key and holding it to start position. The check engine light is often on and the code is for a cam shaft sensor or resistor sensor. A companion problem is the cruise control. If the check engine light is OFF and I use the cruise control, it works fine for a while and then the check engine light comes on at the same instant the cruise control turns off. Are these 2 issues connected? How much should it cost to have the sensor replaced? The car always stays running once it starts and the problem occurs randomly. What are the consequences of not repairing it?
View 1 Replies
I'm trying to find the power steering pressure switch for a 2002 PT Cruiser. I have been under the car and located a pump on the passenger side with a two prong connector. The connector looks to be in good shape. I thought the switch was replaceable but there was nothing to screw out only two prongs going in. Am I looking at the wrong part and if so where is the power steering pump?
View 4 Replies
It's a 2005 Chrysler Sebring with a 2.4 DOHC. A couple weeks ago I tried to use the wipers and nothing happened - at all. The next day the gauges inside the car went hay wire, started flashing on and off. Turned out the car needed a new battery and alternator. Replaced both and the car has been perfectly fine - except for the wipers. I checked the wiper fuse and it wasn't blown so I pulled the cowl, unplugged the motor, turned the key on, turned the wiper switch to full speed and then tested for voltage at the plug and got almost 12 volts when testing several terminal combinations.
I thought for sure I had it figured out so went ahead and bought a remanufactured wiper motor but nothing happened when I plugged it in. I thought maybe since I didn't mount it it wasn't grounded so went ahead and did that and still nothing. Thinking maybe it was defective I returned it and went to a different auto parts store and bought another one, hooked it up and got the same results. So then I tested all nine relays in the relay control center and they all passed. So now I'm thinking the only thing left to test is the wiper switch. Am I correct?
And also I'd love to bench test the original motor just to verify that it works but don't know which terminals to connect to. I've searched the internet with two different browsers and came up with nothing. The motor in question is a Bosch 05-02-14 41. And then underneath it has 0390 241 7411 12V 058 written on it. The terminals are labeled: 31b, 31, 53 and 53b. And since the OE replacement motor for this car is a Cardone 40-3026, which terminals to use to bench test that one, I could then figure out which terminals to use on the Bosch.
View 19 Replies
I have a 2006 Jeep Commander. Periodically, and quite inconsistently, all the lights on the dash board flash on and off while simultaneously all the gauges drop to zero and the air stops blowing out from the vents. My car will continue to drive and all lights work along with the radio. This has happened while driving at 75 mph on the highway and my car will continue on as if nothing has happened. I know this isn't good, but completely baffled by it all. I have taken it to a Jeep dealer and they only saw there was a weak reading from my battery, but the battery isn't even two years old so I have yet to replace it.
I'm including a video I took while stopped at a light so you will see the RPM's drop down, but since I wasn't moving the MPH remains at zero.
View 4 Replies
My son's wife has a PT Cruiser, she told me last night that it has a shimmy at 70 mph. What are the causes of this ?
View 10 Replies
My PT has a vibration, I've replaced rear drums, rear hub assemblies, front brakes and front rotors and all four tires.The vibration is only while going 55 to 60 MPH each time I've replaced the different parts (rotated the tires and rear drums) the wobble seems to go away for about a few miles and then comes back!I'm going to replace the front hubs and bearings now, but why would the wobble change each time I changed I've changed all these parts around. Could it be a bent rim? or just the front bearings?
View 5 Replies
