Ford :: Very Difficult To Get 2006 Mustang (manual Transmission) Into 1st Gear
Apr 30, 2013
I have a 2006 Mustang (manual 5 speed) that recently has been having a problem getting into 1st gear
Symptoms:1. When the engine is cold, there is no issue getting the car into gear2. Once it warms up (after approx. 20 miles or 30 minutes driving), it is very difficult to get into 1st gear. I have to put it in 2nd then get it to slip into 1st.3. On hot days the problem starts sooner and is hard to get into the other gears4. when the car has warmed up on a cool day. I can get the car into the other gears (2nd, etc) when standing still, but first is almost impossible
Originally the problem showed up when my wife drove the car, but it is getting worse. Why the engine and/or outside temperature would affect how my I can get my car into gear?
View 6 Replies
Advertisement
2007 V6 Mustang Manual Transmission. I recently got stuck in my drive way due to a poor plowing job by the plow guy. I had to turn the traction control off and aggressively shift transmission between reverse and 1st to rock the car and spin the tires. I eventually got unstuck but now the transmission doesn't feel right.
I thought it was the clutch but the issue seems to occur only shifting from 1st to 2nd. The higher gears all seem relatively fine. There is just a catch between 1st and 2nd now that sometimes causes me to not be able to shift into second gear without forcing the shifter down roughly.
Is it possible that I just threw something out of alignment inside the transmission itself? It doesn't make the car undriveable but i get ticked every time i drive it knowing that it was fine before the poor plowing job.
Should I even bother having it looked at? I know transmission repairs are expensive.
View 1 Replies
In the last 8 months I'm having a shaking of the car when starting in first gear (manual trans).
I thought it was a loose engine mount - had it checked and one replaced and still the shaking is there.
I notice it is more pronounced when the engine is hot and starting on a decline.
Since I've had this Camry (almost 8 yrs), I've had the clutch changed 2x. First time was just wear and tear. The person who replaced it put the fly wheel on backwards! Drove it for 3 years until it just broke. Replaced by another shop who couldn't believe I got three years out of the bad job.
At any rate, this doesn't feel like a clutch-related issue. No slippage feeling or other issues when moving through the gears at higher speeds. But maybe they did a bad job too?
View 8 Replies
I have a 2010 accent blue model with stick shift. been fine for 50k miles. Lately i have noticed an issue where i am in first gear and then when i push clutch in to go into second, the lever won't budge. it does eventually go in but it just isn't like it used to be. it happens say about 25% of the time. Since at higher rpms it won't do it but normal rpms it will.
Also, i just had a new short block installed, perhaps something is binding? If I sit in the car, stopped, i can shift into and out of all the gears perfectly. Maybe my 1st gear synchros are going?
View 2 Replies
I just got my 03 F-150 with 112k on the clock. It has the manual 5 speed tranny behind the 4.6L.
However, since I've gotten the truck, it's kind of difficult to put in first gear. If you are sitting at a light and in neutral and the light changes and you push the clutch to the floor and put it in 1st (fairly quickly - a normal reaction time), it will actually do a little grind and/or thump. However, if push the clutch to the floor and wait a couple of seconds and then shift into first, it's a bit of a "push" but it will go in without grinding.
Once in a while shifting to 3rd it feels the same way, but won't really grind.
I'm just wondering if that means the clutch is toast or is it the trans that is toast? Reason I ask is my 96 Cobra with the T-45 5 speed would grind going into 5th gear if I just normally put it in. I used to have to put it in neutral and then push the clutch in again and slowly shift to 5th for it not to grind. And it wouldn't go into 3rd if I tried to shift fast or under power. I replaced the clutch and found out the trans was actually going bad, but it had 173k on the clock.
So, I'm really paranoid that it's my darn trans in the truck instead of just the clutch. Whenever my old Camaro clutches used to be dying, they would slip more than they would ever grind going into a gear.
View 14 Replies
Our 2002 Elantra (automatic, 57000k) seems to have a blown transmission. A few days ago, it sounded like the car was "whining" and then it was having difficult time engaging next gear and eventually check engine came on and the car stalled. Firestone said it's a transmission problem.
We've had the car for less than 10 years so technically this should be covered under their powertrain warranty but I have a strong suspicion that the dealership will find a reason to not honor the warranty. It's still below 60k miles so we really didn't have to replace transmission oil.
View 5 Replies
My transmission is manual, front wheel drive, 4 cylinder motor, plunger has come disconnected from shifting forks, car is stuck in 3rd or 4th gear. Would it be easier to change transmission or is replacing the plunger mechanism a viable option?
View 3 Replies
Why my vue manual tranny only goes in first third and fifth . Can't get it in second fourth or reverse . Bought it like that .
View 1 Replies
1997 Saturn SL ... It's like 3rd gear is where 1st used to be and 4th is where 2 used to be. 5th and reverse work but are more towards the center. It's as if the stick shifted over to the left.
Is it possible for the shift stick and it's linkage to become displaced? The temp did drop today about 40 degrees and it snowed but the car stays in the garage and was only parked at my work for a couple hours after a 2 mile uneventful drive.
No warning lights that I can see but the check engine lite has never worked. The engine is a 96 rebuild but the transmission should be a 97 like the rest of the car.
Great mileage and otherwise drives fine.
View 4 Replies
My 1997 Saturn SL2 with 5 speed manual transmission won't shift into first or second gear. When I shift into the location where first would be the car is in third gear. It shifts into 4th, 5th and reverse just fine, though the shifter is in the wrong position for those gears. I can wiggle the shifter in neutral and get it to move into the position where 5th and reverse are normally found, but it is stiff and makes a clunking noise when I move the shifter over to the far right side.
I have removed the center console and the bushing appears to be intact. Both cables are in their proper positions inside the vehicle and at the engine. One of the cables (the top one in the engine) has some wear and tear on the boot, but does not appear to be binding. Other than the stiffness and the clunking noise, the shifter seems to be working fine too.
View 8 Replies
I am loosing gear oil through an odd place . There appears to have been a rubber boot or cover over this area that got cooked by a hot exhaust (whole other story there). This is left (passenger side) just above where the axle enters the gearbox. Not sure what this is and how I can resolve the issue. I have temporarily used silicone to stop the flow and have topped off the gear oil, but am still leaking a little. I have already done some damage to the bearings I fear, as the tranny really whines when I get up into 4th and 5th.
View 4 Replies
What RPMs do you see in 6th gear, say at 60mph or 80mph? Consumer Reports claims the RPM at 60mph is 3020!
So I went to vw.com to look at the gear ratios for a reality check. The site lists two final gear ratios for the manual. "Final I" is 3.94 and "Final II" is 3.09. When do you get one versus the other? With a final gear ration of 3.09, I get roughly 2400RPM at 60mph. But with a ratio of 3.94, I indeed get about 3000RPM at 60mph or 4100RPM at 80mph!!! That's absolutely insane.
View 11 Replies
My 88 celica's manual transmission grinds a little, at times, when going in 3rd gear. I have atf fluid in it now as specified in the manual. Should I replace it with gear oil?
I don't want to damage the transmission or clutch.
View 2 Replies
I have a 98 saab 900 se turbo.90000 miles on it. Just had a new clutch kit/throwout bearing and master cylinder clutch installed, as the clutch was going bad.
When I shift the car (while driving) from 2nd into 3rd/4th/5th gear,and accelerate I suddenly notice what sounds like a "grinding"/raspy noise that stays with the car while in those gears. It does not occur in 1st or 2nd , although it seems that in first gear the rpms go up real fast now (could the gears be slipping again?? this is a brand new clutch..).
The second I shift to 3rd gear and give it gas, the noise shows up instantly. Now when I let my foot off the gas, the noise goes away 100%. The second I give it gas again, it comes back. Also I don't believe the noise increases or decreases in relation to the speed of the vehicle. It seems to stay constant no matter what speed I'm at, as long as I'm actively giving it gas.
It occurs every time I drive..not sure what to do and what causes this..maybe I just need to check the transmission fluid?
View 19 Replies
2004 Jetta 1.8T w/5 speed manual transmission. Bought the car this way, mostly for a parts car, but everything else runs and drives good, so if it wasn't for this issue it would be a decent driver.
Won't/can't select first gear. Seems like there is no "spot" for first, or that the shift mechanism has no where to go., locked out. All the rest of the gear selections work perfectly. Tried the cable adjust ritual, but it was fine-as I suspected. The shift assembly works/moves perfectly from the tranny end and the shift lever end. Not a synchro, it won't go in stopped, moving, running or shut off.
So, what's the probable best guess or best way to come to a diagnosis? Shift tower parts broken somewhere, or something like a shifting fork bent broken? Seems like if it was internal there would be other gear selections that would be affected. Any links to some diagrams?
View 7 Replies
My 2003 Corvette has 17,000 gentle miles on it. At around 15,000 miles I found that I couldn't get the car into 5th gear. It has a grinding metallic sound. All the other gears and the clutch work fine - and I've been forced to shift from 4th to 6th.
View 5 Replies
I was recently driving my 1993 Volvo 240 wagon over the Bourne Bridge in bumper to bumper traffic (surprise!). Traffic was moving at 3-5 mph as I navigated the rotary and ascended the bridge. Needless to say, I was developing leg cramps as traffic crawled up the steep bridge incline. Once I crested the hill, I shifted to neutral (still 3-5mph to coast down the decline and give my leg a rest. After coasting for a few minutes I attempted to shift into second gear to re-engage the transmission.
I was unable to slip the gear shift stick into any gear! I continued to make sure that I was depressing the clutch all the way to the floor, but still could not muscle the stick into a single gear (by the way, I never smelled that "burning clutch smell"). After about a minute or more of mental disaster planning, I finally coerced the shift into third gear. A minute or so later, I was able to shift into second gear which got me around the accident causing the delay and onto the highway. From that point on, I was able to shift normally for the remainder of the 2 hour trip. What happened and what could I have done to solve the problem? (The car is now at the repair shop where they are equally perplexed).
View 19 Replies
93000 miles 5 speed manual transmission only lets me use 2,3 and reverse gear. I took good care of that car and dont think transmission should go out that soon/
View 7 Replies
Just curious if there are any other 2010 owners with any difficulty shifting gears in their manual transmission camrys? I noticed during my test drive that I grinded my way into 2nd once... I thought it might have just been my nervousness with a new clutch at the time. However, I've since put 300 miles on the car and I still have trouble putting it into second gear on a daily basis. Sometimes it grinds a bit, and sometimes it catches or a half second before it pops in. All the gears OTHER than 2nd gear go in like butter as you would expect with a new transmission. I'm not new to a clutch... this is at least my 4th car with a stick, so I don't think I'm doing anything out of the ordinary when shifting.
It reminds me of some older (100,000+ mile Nissan) cars I've had in the past... the syncromesh was wearing out and it would grind going into second or third, so I put in some RedLine MTL and got a little more life out of the transmission... but there shouldn't be a need for that kind of thing on a car with less than 1000 miles on it?!
View 14 Replies
I just picked up another GTi and knew the transmission was iffy when I bought it. I had to deal with the serpentine belt tensioner which is now new and also a new waterpump since it was wobbling.
I've already drained and replaced whatever oil was in there with VW G60 Gear Oil which is what my Dealer here told me to put in and it shifts smoother now but still has the same issue. I also did the Shifter Cable adjustment to see if that was the problem but that only made it easier to shift but it still got stuck.
Basically what happens is when driving I shift into 3rd gear and when I go to shift out of 3rd it comes out of gear but it's like it hits a brick wall and will not go into the home position. I was hoping the adjustment and new oil would work but it hasn't done anything.
View 2 Replies
I have a 2005 Elantra GT hatchback that I love with a 5 speed transmission. Lately every time I'm in 2nd gear, the transmission will pop out of 2nd into neutral. This only happens in 2nd gear. I heard it could be the shift collar (i.e. teeth?) that aren't grabbing in that gear.
View 5 Replies
