So this has happened a few times pedal drops with no back pressure then give a bit pull it back up by hand and it's fine has happened 4 or so times in the last year. I'm reluctant to replace slave and master cylinders could it be anything else? 87 Ford F-150 hydraulic clutch
View 10 RepliesI just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 Replies1996, f150, 300, 4x4, 5 speed, 296,000 miles... My pedal goes almost to the floor before the clutch engages and about a half inch, maby less, of travel back out the clutch disengages. I think it is about time for a new clutch. My question is what is the best clutch to put in my truck?
while i have the transmission slid back to replace the clutch i am planning on replacing the slave cylinder while im in there as well. Any particular brand better than the next on that item? Are there any other items that I should think about replacing while i have the transmission slid back to do the clutch?
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 RepliesI have a 1995 F150 with the 4.9L and it has 73000 miles on it. One morning recently (it was about 35 degrees outside) I went to start my truck to let it warm up. When I let off of the clutch it stayed on the floor. I shut it off and drove my car to work instead. I asked around at work and one guy mentioned that it was probably my clutch master cylinder...so that day we replaced it, and bled it until it felt like knew. Since then, we have had to bleed it three more times, because the pedal keeps losing its pressure making it harder to shift. I have inspected around the clutch line and the bellhousing for signs of needing to replace my slave cylinder, but everything looks fine.
View 8 Replies1998 Passat 1.8T FWD. My clutch pedal is stuck to the floor and wont spring back up. I can't seem to find the little tank to check the clutch fluid. I have heard the it uses the same tank as the brake lines do, but the tank that holds the brake fluid is full. Can it be the slave cylinder is gone? or just got a air pocket in the line?
View 1 RepliesJust a heads up to all MKIV GTI owners out there, new and old. If you feel like the tension on your clutch pedal is deteriorating get it checked earlier rather than later. Because if the slave cylinder malfunctions and leaks you will be faced with a big repair bill due to the fact that the slave cylinder is located inside the tranny. Secondly because of this design, which I think is very stupid, it leaks onto the clutch assembly and can get on your clutch plate. At that point you should replace the clutch plate to prevent any further damage that might be caused by slippage. The clutch plate should not come in contact with any fluids or it will compromise the functionality.
View 2 Replies1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 RepliesInstalled a new clutch and slave today. Kept the same master cylinder.
The problem I am having is that the clutch pedal will not go to the floor, and therefore the truck won't start. The slave is moving back and forth roughly 3/8 inch, maybe more. I am pretty confident that there is no air in the system.
If I loosen the pressure plate a little, the clutch will go to the floor. But tighten it back up, and it again only goes down about 75%. This is a late '95 so it has the self adjusting clutch. I did get the correct kit for it, as well as slave. It's like the self adjusting part is too far adjusted and won't let my slave travel as far as needed.
In troubleshooting, I did notice that I failed to get the dowels in the flywheel aligned in the pressure plate. I am old school and not used to dowels in the flywheel! The dowels are not hitting anything and are not preventing the pressure plate from seating on the flywheel. But it is something I'm going to fix if I have to pull the trans again.
For reference, I replaced the clutch because the slave cylinder was hanging up and preventing the clutch from getting fully released. Aka clutch slipping.
I have a 06 f360 PSD 6 speed. On a road trip and the clutch pedal is getting very close to the floor. No Slippage but the longer I leave the pedal pressed the worse it gets. Are there any good descriptions how the clutch in this truck works?? Slave cyl??
View 14 RepliesI am working on a e-150 van, 2005. the brake pedal fades to almost the floor with little pressure on it. I just replaced the master cylinder, bled the entire system, and it STILL fades to the floor. driving, or in park. engine running. 4 wheel disc, 4 wheel abs...
View 5 RepliesTook truck to a mechanic he advised me that the no heat was because of high back pressure in engine...never heard of this before, is this a correct diagnosis? No heat, air blows through all vents, defrosters.
View 1 RepliesWhat is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
Pulled out of street this morning and as I was shifting into 3rd my clutch pedal went straight to the floor boards. I was able to keep it in 2nd gear and get it back to my driveway . The pedal will only go straight to floor or goes straight up too the bottom of dash board. It's spring loaded. Am I dealing with a linkage issue?. I had clutch as I pulled out of my driveway and stopped go at the stop sign. Plus I was able to drive it back too my house with the pedal on the floor boards. Where I should look first?
View 4 RepliesSo my clutch has been acting up lately. When it sits for a few hours the clutch engagement point seemed to creep down but over the course of 35 minutes of driving would work its way back up again. Today it was unusually low and wouldn't let me get it into gear. I tried pumping it a few times and realized it wasn't coming back up all the way, I pulled it up and then tried again and it just dropped right to the floor where it now sits. Fortunately I was at work and can hang here until my ride arrives, and will just wait until late tomorrow night to drive it to my shop without stopping...
My guess is I need a new clutch master cylinder. I have plenty of fluid in there although its a bit old so I'll be changing that when I change the cylinder. Could it be the slave cylinder? If so is it a bear to change that? (do I need to drop the trans?)
My stock 2009 ford f250xl 4x4 with a 5.4 and 6 speed has been giving me a weird sound lately started about a month ago and only happens on a cold start situation meaning if it sits over night it will do the sound. the sound goes away after 3-5 min of warm up in my driveway, the sound happens when i push the clutch pedal to the floor. it has no pronounced abnormal sounds through out the rest of the day when its hot which perplexes me, check out the vid on my u tube site for a sound of it.
MAH00111 - YouTube
MAH00115 - YouTube
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
My clutch pedal went all the way to the floor. The engine was missing first and then that problem happened with the clutch. I had the car towed to my business, I checked it the other day and the pedal was up. The clutch still doesn't engage.
View 6 RepliesI have a 1998 Ford F150, Manual transmission. It has set for 1 year. Upon driving it for the first time yesterday, it gradually came to a stop. The clutch never smelled hot or appeared to slip. Today I took the inspection cover off and found a rather large nest has been built in the clutch and pressure plate. My question is could this nest cause the throw out bearing from allowing the pressure plate to make proper contact with the clutch. The truck will move in 1st gear and in reverse as long as there is no resistance against the truck.
View 2 Replies