Ford - Ranger :: 1992 - Light Tapping While Accelerating
Jul 20, 2012
I have a manual 1992 ford ranger V6 with a 3.0L and for a while now i have been hearing a VERY light tapping sound while accelerating. its so quiet that most people can barely hear it when I turn off the radio and A/C. For about a year or so I could only hear the tapping when I was going up an incline in fourth or fifth gear, but recently I can hear it on flat roads but only occasionally, Again I can only hear it in forth and fifth gear and only when i first get in the gear,when i speed up it goes. I don't Know if this is good but I change the oil and spark plug regularly.
View 11 Replies
Advertisement
Started having an issue with my '92 E-350 box truck. I noticed a slight hesitation while driving which I thought was a miss from perhaps a plug wire jumping or something. It didn't do it all the time, just occasionally for a few seconds then would clear up. I looked for a bad wire at night but couldn't find anything so I said hell with it and changed plugs and wires, cap and all.
That didn't fix the problem. Progressively the problem has gotten worse. Then I started hearing a pinging, almost tapping noise as the truck was stumbling. Now I've noticed that the motor seems to be running fine as it does it which has led me to think it may be in the trans.
A little background on the trans. About 6 months ago the van started randomly conking itself out coming to a stop after a few minutes of driving. It seemed the trans was bogging the motor down as if it were locked together. If I put the truck in neutral coming to a stop it wouldn't do it. I went ahead and had my uncles shop flush the trans and he put some sort of synthetic fluid in it.
Since then the van has never done the cutting off thing again. All seemed well. Then this started. It does it from take off through all the gears even in OD. It almost feels as if someone is rapidly hitting the brakes. I thought maybe malfunctioning brakes however soon as I'm not pressing the accelerator it doesn't do it.
Today I had about 4000 lbs of wood in truck and it was a horrible trip. The truck would barely get up to speed. I unloaded the wood and on the way home it only seemed to do it going up hills so it seems any load on the truck makes it happen.
Does it seem I'm in the right area thinking transmission?? Being it happens in every gear would a torque converter seem to be a possibility. When I was having the cutting off problem I was told it sounded like the converter wasn't unlocking but the flush seemed to fix that issue.
I haven't pulled the pan to see if there's any surprises in it and I did the diagnostic check and there wasn't any problems found. Any other manual diagnostic checks?????
View 1 Replies
I got my b2500/ranger a couple of months ago and I've had very poor gas mileage. I replaced the air filter, changed the plugs, no luck. The truck has 169,000 miles. I haven't checked my exact gas mileage but from what i am seeing its horrible. I filled it up last night, not completely full but really close the full marker. In the morning i drove to school (7 miles) drove home, so 14 miles. Then i had to go back out by my school to pay back a friend. All in all about 28 miles. This cost me a little more than a quarter of a tank. The 2.5l has a 16 gallon fuel tank, so if my calculations are correct im getting about 8 miles to the gallon. I also took it the consideration that it was a half gallon from full.
And it wasn't just past below a quarter to full it was 3/4 of the way to a quarter from full. I know that i didn't test the mpgs "properly" but i think its close enough to draw a conclusion from. And keep in mind its not a 4.0, its a 2.5! Although i do think the engines size contributes to the mpgs because it takes ALOT to accelerate in this truck. At 2k rpm im barely accelerating from a stop light. And on the highway my engine stays a 2500 rpm doing 60-65. I am really hoping I can fix this because I don't want to drive around in a civic. Plus I need a truck for scrapping which is how I pay for gas as i am 17 and jobs are scarce. Also I know about cleaning the MAF butit has tamper proof torx on it which i do not have the tools to remove. I think it could also be the o2 sensors.
View 14 Replies
I have a 2010 Ford Ranger Sport. RWD with the 4.0L. Currently Sitting at 46,000 Miles.
Where I am located, it is very cold. Downwards of 5 Degrees F. I just started noticing a strange sound in my truck. When accelerating from a stop light I hear a single knock, and to my ear it sound as if it was coming from the rear. First thing I did was check the U-Joint, but there is zero play and it is very tight.
After driving quite a lot and unable to diagnose the problem, I part and got out of my truck, only to hear that same noise when I stepped out of the truck. (I am not fat 195b lol). So I sat back down and I heard it again. Did this a few times and consistently heard it. I got into the bed of my truck and started to jump around and got the same knock.
I shook the exhaust pipe to see if it was making the noise, but it wasn't, which makes sense considering while driving over bumps I could not hear anything. I am totally lost as to what this could be....I want to add that I CANNOT feel any difference driving. Feels great.
My ideas on problems are as follows;
-Spare tire
-bushing
-loose bold
-leaf spring (maybe a hanger)
-The cold creating noise like always.
View 3 Replies
Ok, so I have a 1992 GMC Suburban with a 350 TBI with a full dual exhaust and long pipe headers. The problem I'm having is that there is a tapping noise that comes from the driver's side of the engine when you push the gas pedal down. It only makes the noise when you push the pedal down more than about a quarter of an inch. I have tested it down hill with the transmission out of overdrive and the rpms up and there is no tapping. I'm thinking it might be pre-ignition in one of the cylinders but how to test for it other than just disconnecting plug wires one at a time until it stops. Much more I don't know what would be causing it to happen if that is the problem.
View 10 Replies
My 2003 Ranger 2.3L When I purchased it in 2005 I never noticed this tapping noise until in 2007 when Tennessee forced 10% Ethanol added to fuel. That is when the noise started.
What this could be. I have since moved to Texas and found a station that sells Ethanol Free gas, but that does not remove the noise.
View 11 Replies
My compressor on my 92 Ranger did not have any clutches on it. Where they went. I got a compressor off of a 94 at the pick and pull. It was charged and the compressor turned fine. Brought it home and tried to install it. My hoses in the back of mine(92) are different than the 94. I went back and got the hoses, condenser and evaporator off of the 94. Put it all together. The high pressure hose on the 94 has some sort of switch on the high pressure side. What is this switch for and how can I wire it in to the electrical system on the 92? I assume it is some sort of pressure switch that allows the system to flow. I'm getting 30 pounds on the low side and 150-200 ponds on the high side. Also, when I increase the RPM's, the compressor kicks on and off. It's not like it would or should normally but fast.
View 7 Replies
I have a 92 ford ranger. About a year ago it shut down on me as I was pulling out of a parking lot. I replaced the Cam sensor which IS NOT located on the engine block by the fire wall. It is located on the front of the engine just above the primary cam which is just above the crank shaft and its sensor. It fired right up.
Then the oil pump went out and I just replaced it the other day and the pressure gauge/needle went past the half way mark even at idle. I drove around a bit, maybe 10 miles, then got in it to go to the gas station and got about 50ft from the house and it just died again and will not crank back up.
I am thinking its that darn cam sensor again. But, just like the oil pump was, it's a pain to get to and replace. How to test it. Oh, it is a 2.3 4 cyl. double overhead cam. I do have fuel pressure, I checked that already.
View 14 Replies
I am the owner of a 1992 ford ranger 4.0 that refuses to start. She turns over, but theres no pressure coming out of the fuel rack/valve. Might be the fuel pump but it started with a little boost about a month ago and now nothing. Head gasket and transmission have been tuned up as well! I've also checked the power distribution box, and spark plugs both seem to be doing thier job! What am i missing?!
View 2 Replies
My 1992 Ranger has a 2.3L 4cyl 100hp engine with 207k miles. It occasionally hesitates when beginning to accelerate but never when at idle or when driving at speed. I don't even know where to begin. The engine has had consistent maintenance and runs well otherwise. This hesitation makes me afraid that it will damage the drive train somewhere. I'd like to at least know what the problem is even if I can't fix it myself because I've done most of the work on the engine.
View 3 Replies
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 Replies
Ok I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
View 2 Replies
My Ranger was running great when suddenly on the highway it just died. I towed it to local nationally known brake/ muffler shop where a good friend is the manager. He narrowed it down (guessed in my opinion) to no spark and no fuel. He thinks it could be the crank sensor, the fuel pump or the ignition module. Is there any way to pinpoint the problem without replacing parts? It will sometimes start and run for about 2 seconds before shutting off. It will not repeat this unless it sits for a day or two. I am not sure if there are different 2.3 engines available but mine is fuel injection and has two sets of spark plugs and wires.
View 9 Replies
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 Replies
I recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 Replies
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
View 3 Replies
I'm working on a 1992 ranger with the 2.3l. Hard start almost every time, sometimes have to hold throttle open sometimes not. Won't start at all this morning. When it does finally start it takes a while for it to start firing on the intake side plugs. Haven't had time to check fuel pressure yet but can hear pump cycle when key is switched on.
View 8 Replies
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
View 1 Replies
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 Replies
All I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 Replies
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 Replies
