Jeep - Grandcherokee :: Brake Pedal Spongy And Almost Reaching The Floor When Pressed
Apr 27, 2013
After my local brake shop changed the front rotors and brake pads on my 99 grand cherokee the brake pedal is spongy and long, almost reaching the floor. They don't know why. Apparently they had a problem with fitting the new pads. I took it to the jeep dealer and they told me the master brake cylinder was leaking and needed to be replaced. many hundreds of dollars later the brakes are still spongy and long and does not correct with repeated pumping. The dealer was also stumped and I complained that nothing changed with the new master cylinder. what might be the problem?
View 4 Replies
Advertisement
I have a 2006 Grand Cherokee and since I bought the car used the rear right brake has squealed despite having the breaks replaced and serviced twice. I have had the car for less than a year. Recently I have noticed a bit of a shake/thud while I'm driving at speeds lower than 45mph. It almost feels like I have a flat tire, despite all of my tires being properly inflated. I do not have to be pressing the brake to feel the shake, however I do feel the vibrations in the brake pedal. What could be the problem and could it be dangerous?
View 3 Replies
Details about my car: '91 Nissan Maxima. His name is Max. 183,265ish miles on it. Transmission was replaced maybe 8 years ago(?) My dad said the oil was changed at the 500 mark. Filled the tank up at Citgo with regular gas on Friday and only drove about 50 miles (I fill up every 200 miles or less). Max turns on but you have to floor it just to move an inch and it smells like gas.
View 15 Replies
My dad drives an '06 Sonata. And he recently broke a brake line and had gotten it fixed. His current problem is that his brake pedal hasn't returned after getting the line fixed. What can he do to fix that? The pedal is really low and is spongy. And his ABS and ESC lights are also on.
View 4 Replies
I have a question about the bleeding the brake? When I washed my E, I usually spray the wheel and the brake part. I don't know it is a good idea or not. Recently, I felt like I have to step further on the brake pedal to apply the brake.
The force is there and Brake assist is still in effect if I step fast enough. I just felt like the brake pedal is spongy. My E is on 36k right now. Do you think wash the wheel often will cause the problem to brake line?
I have confirmed that my Gf's Elantra is easy and ease to brake than mine. At the mean time, her brake fluid is darker than mine. My brake fluid is full and clear. Maybe I should not wash the wheel more often. Or maybe I get OCD too much?
View 22 Replies
02 Montana with 4T65E electronic 4 speed transmission. car has 75000 miles. normal driving and shifting seems to be fine. Transaxle will not downshift with accelerator pedal pressed to the floor. no check or service engine lights.
View 1 Replies
I have a 2000 Silverado 1500 replaced calipers, master cylinder, and ABS Pump/Modulator. Bled all four calipers. Brake pedal spongy and has very little pressure and travels all the way to the floor. What am I missing here?
View 8 Replies
I just finished replacing pads, calipers, rotors, wheel cylinders & brake drum hardware on my truck along with flushing the brake fluid. The brakes work but the pedal goes almost to the floor. While bleeding them some air did come out as expected. But a couple times the master cylinder reservoir got very low on fluid. The workshop manual talks about bleeding the MC but are special fittings needed for that?
View 10 Replies
Drove the lady's car out on some errands today and ran into a problem on our drive home. Car was pinging really bad (low rpms in 1st and second) and car seemed as if it couldn't get out of its own way. Was driving for some time on the freeway (after a blistering 0-60 time of 20 seconds ), and noticed that the brake pedal was really spongy (felt like a mk1 when you try to brake with the car off). Found that the e-brake handle was up (negligibly up (perhaps 1mm raised)). Didn't have power brakes at all and had to use a lot of engine braking to slow the car off of the freeway.
Rear of the car smells like copper (wet pennies) and found that the brake reservoir is cracked (but fluid still at max level). Also noticed that as of late, when the car is at a stop (sometimes in gear, and sometimes in neutral) the car will rock/bump a little almost as if someone were giving it a bumper kiss with their car.
View 2 Replies
My Gen I Prius is screeching at me with the BRAKE and ABS lights on, and I hear the electrically actuated pump pulsing as it tries to get pressure into the system. The pedal is spongy and will go all the way down, with the right amount of exerted pressure from my foot.
View 6 Replies
Ok, did an intake manifold cleaning on my 99 Accord the other day, and now I have problems...
Long story short, some time ago my car started to have a very rough idle. Took me awhile to find the problem. Turned out the air hose, between the filter and throttle body, had developed a big hole on the underside. So I replaced it and while I was at it used some throttle body cleaner, spraying into the intake manifold chamber. Lot of junk blew out the tailpipe. The car ran much better, but the idle could still be a little rough. I ran it that way for awhile, and finally the other day decided there was probably still some junk in there and it was time to really clean it out. So I took ff the throttle body and intake manifold housing. There was a lot of junk in there! The small intake on the passenger side was completely clogged shut. (I understand this isn't surprising on these cars.) I used a bunch of rags and 2 cans of Valvoline throttle body cleaner and a lot of elbow grease and cleaned it out. I was thinking to myself that whatever I didn't get with the rags flushed through OK, but I didn't want to take the whole intake manifold out.
So I put it all back together. (I took a video before I started, so I'm pretty sure it's all back together right.) But now I have problems. The car starts. It idles fine mostly, but can be a bit rough. But the trouble starts when I put the pedal down. If I do it in Park, well, if I push it quick the engine just dies. If I push it slow, the engine revs then quits, revs and quits, over and over. Similar if it's in gear. If I push it hard, the engine stalls. If I push it gentle, it revs up, but chugs along a bit.
I've run some seafoam through it, thinking it was clogged up with all that junk, and sure enough, lots of smoke comes out, but nothing is improving so far. What have I done wrong?
View 19 Replies
I have a 2008 Ranger Sport 4x4. I noticed yesterday that when I stepped on the brake pedal it felt like nothing was there until I step a little harder then it was like full brake application. The truck only has 63000 on it. Then every once in awhile it would be normal ie very light brake application and slows like it should. Then back to same issue... Any thoughts about this??
View 8 Replies
2009 XRS ABS brakes .... I changed all four brake pads and flushed out most of the old brake fluid. Bled all four sides. But now while I am in idle (like waiting for a light to turn) my brake pedal is spongy and is making a hissing sound. All was good before I did this job.
View 3 Replies
I replaced all the brake pads on all 4 wheels. Pretty standard procedure. I now have a very spongy brake pedal. It stops but the pedal will be almost to the floor. I did not break any of the lines open during the procedure just used c-clamp to spread the calipers. No ABS light. Have a Snap-On power bleeder and bled the system several times with no change. Checked the power steering fluid level and inspected entire system for leaks.
2002 F-550 V10
View 8 Replies
2002 Jeep Grand Cherokee. None of my tail lights or break lights are working. Turn signals, back up lights and license light work fine. Fuses all seem good. What could be happening?
View 4 Replies
Recently my F350 has failed to downshift when the accelerator pedal is pressed to the floor to speed up in traffic. It will usually happen when traveling at speeds in the 30's-40's. It will shift quickly at slower speeds. I have a scan guage on it all the time and it is not throwing any codes.
The transmission has only been serviced by the dealer; last done about 24000 miles ago. No leaks or low fluids/no burned smells. Stock setup with no heavy towing use. Currently at 228000+ miles, this is the first issue with the transmission assuming I am looking at the right area for the cause.
2005 F350 XLT 4WD
View 8 Replies
I own a 04 Grand Cherokee and have recently had problems with my passenger side brake light. Now the light itself does work under normal running light conditions, but when I go to press the brake pedal it doesn't engage the bright brake light. Drivers side works fine and so do all my other lights, I replaced the bulb to no avail, and am now currently looking into replacing the bulb socket.
View 1 Replies
I noticed last week that my brake pedal seemed more spongy than usual. The next day the pedal would go down about half way to the floor before I had pressure. And then the next day the pedal would go straight to the floor. Pedal comes back up once released. I still have brakes pressure about an inch before the pedal bottoms out. Its been like this a couple days now. The vaccum pump works fine. I'm gunna try bleeding the brakes on it tomorrow.
View 5 Replies
I have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 Replies
I was wondering if this problem is the "Barking" noise that keeps coming up the search or is it another problem. I will include a link to the video down below.
To start off, the Prius is 2010 Prius II and has 120k miles on it. Great Car. Only other problem was AC compressor dying at 90k.
The chirping noise happens when the brake pedal is pressed and does not go away until the release the pedal. It makes the noise regardless of whether the car is on or off.
It makes the noise when the car is stopped and or when the mechanical brake engage at between 0 and 6 mph.
Noise does not occur when the brake switch is removed. Not valid solution since the brake lights will stay on. It does not affect the performance of braking.
Here is the link to the video .... .... ....
View 9 Replies
Today I faced another problem i just try to start my car but, due the dead 12v battery it didn't start so i pressed the BRAKE PEDAL until it reach the bottom, again i tried to press but its not going to the bottom why was that, is it due to dead battery? And last time i called an automobile expertise to jump start my car. They check the voltage with a digital multi-meter and he said me if you jump start even you will get this problem again until u replace the new battery. but i said him it doesn't matter do a jump start and finally it was ok . Now again I faced the same problem and this time i am going to change the battery.
View 1 Replies
