Jetta - Volkswagen :: 2006 - CEL Code P0332 / Knock Sensor 2 In Bank 2 Faulty
Mar 27, 2014
I have a 2006 VW Jetta with 92K miles and just a couple of days ago my check engine late came on and when i took to an auto store to check the code, it came as P0332, Knock sensor 2 in bank 2 is faulty. Three things have happened all around the same time and I am not sure if they are related and are just coincidence.1.Check engine light came on.2. I have noticed after that, my car RPM has dropped, idles at about 600-700RPM and when trying to accelerate, it tops at 3000 RPM and feels like the motor cuts off at that point and I have to step off the gas and the car runs ok again, but cant go over 3000.
Had trouble getting on the interstate due to this and thought the car was going to stall, but it didn't. just had to back off the gas and let it run, It did go up to the speed that I wanted, but seems like it wont go past the 3000 RPM point.3. My fuel gauge, drops to empty when it reaches the half way mark on the meter. It stays at the correct level when I start and keep the car in idle, but when I start moving, it drops to empty. When I fill up the tank, it goes all the way to F, and after the car goes the usually of about 190-210 miles, when It reaches the half full level, the meter drops to zero, so have been using my trip odometer to drive after that.
View 10 Replies
Advertisement
I got my car in November and I just did a scan and got this code. I don't have a CEL on. I do feel a slight vibration from time to time. It's very light.
Should I clear all DTCs and then run a scan a couple of days later to see what codes I truly have? Or should I address this code?
If yes, what should I do about this code? Do I need to buy a new knock sensor or should I check the wiring first with a voltmeter?
View 15 Replies
2012 Hyundai Accent. I am getting a po326 code. Wondering if it may be a faulty knock sensor. And po463 fuel level sensor code when I fill up with gas.
View 2 Replies
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 Replies
Got a code for knock sensor bank one however this is the wiring going to it. Could it be throwing the code simply because the wire is cut or do i need a new sensor maybe too?
View 11 Replies
Wife has a 08 solara 2.4 auto. Check engine light is on for bad knock sensor in bank 1. Now car is not pulling itself, it takes off fine then shifts and falls on its face, I think its missing 2nd and going to 3rd. It is also not shifting into 5th so its staying in 4th and using a lot of gas. I tried manually shifting but it still goes to 3rd and will not go to 5th. I have been told this knock sensor could be causing it all. Cant clear code, I hit clear but nothing happens. We don't have a lot of money to pay the Toyota dealer to fix it and I can do all the work but they wont even show me where the knock sensor is.
View 5 Replies
I just purchased a 2006 GS300 AWD w/115k. Started car on lunch hour to find check engine / check VSC lights on. Ran codes to find P0333 Knock Sensor code. Vehicle seem to run perfectly fine, but now that the light is on, it is definity spark knocking under acceleration. This is my first Lexus / Toyota product, so I am unfamiliar with the common problems or fixes. Are knock sensor replacements common?
View 6 Replies
I have a 2010 Toyota Corolla 1.8L, the base model.
I recently had a check engine light, VSC off light (blinking) and traction control light come on. I took it to Autozone and had a p0037 code ring up for a new Bank 1 Sensor 2 oxygen sensor (downstream). I believe I have found the correct sensor (located under car, approximately near drivers seat) and it looks simple to replace, aside from the fact that the wires go through the car body.
Can confirm that I have located the correct sensor? And if so, what is the best way to get to where the wires connect?
Is it located under the drivers seat? What should I do about the rubber grommet located under the car where the wires appear to pass through?
View 2 Replies
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
View 1 Replies
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 Replies
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 Replies
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 Replies
My 2003 Santa Fe 3.5 is in limp mode, you can't change the gears and showing signs of faulty tps sensor, but my mechanic is telling me to change whole electronic throttle system , May be its only the sensor.
View 1 Replies
My first Prius, an 05 has 249K and performs pretty much flawlessly. My second, an 04 which I purchased in May, has 75K. While driving the 04 yesterday, all the lights came on the dash and really scared me. I immediately pulled off the road and checked belt, fluids and anything else I could. I then called the dealer and they thought since the car was running normal, to bring it in. For a hundred dollars I was told the HV battery, though working and not a problem, would have to be replaced due to a faulty "battery temp sensor" and that this part is not repairable....I need a new battery! Code POA9B ... Tomorrow I am taking the rear panel out and check the HV battery fan, etc. Can I drive the car with these lights on? Everything seems to work but the CC.
View 9 Replies
I have a P0171 code (lean bank 1 sensor 1) on my 2002 toyota camry 4 cylinder. I don't have any other codes except for an unrelated P1780 neutral safety switch code. It has had both codes for over a year.
I have replaced the fuel filter, the upstream o2 sensor, and the PCV valve. I also cleaned the MAF sensor. The mechanic performed a smoke test and found no vacuum leaks. Did a fuel pressure test and it's normal. Mechanic thought it would be fuel pressure because the car starts a bit slow when cold, but nope. The car runs great and still gets great gas mileage. I've never experienced a misfire in my 12 years of owning the car. I am asking because I am at a loss as to what it could be.
View 9 Replies
My mother in laws 2012 Santa Fe had a number of dash lights on (ABS, hill decent, stability control). I put my scanner on it and came up with fault code C1209 which showed up as a faulty right rear wheel speed sensor. I have replaced this module and then cleared the codes.
However, the dash lights still light up and the vehicle continues to throw the same code. I don't work on Hyundai's very often so I am at a bit of a loss.
View 1 Replies
So I had a post up saying "is MIL P1444 a urgent fix" and I got "no". On an other website though it said that it was an urgent fix. They said it was "similar to running a bad catalytic converter. You don't want to do it."
P1444:
Possible causes
- Faulty Purge Flow Sensor
- Purge Flow Sensor harness is open or shorted
- Purge Flow Sensor circuit poor electrical connection
So I located the purge flow sensor and look at the tube that connects to that,the canp solenoid, and the carbon canister. Nothing looks bad, but I did notice that the tube that connects to the carbon canister to the solenoid is not connected. The part that connects to the carbon canister dry rotted off. So I turned on my car to see if anything was coming out of that tube or air and there was nothing (not sure if that's good or bad). Also a week ago when I filled up my gas tank (before the check engine light was on) a lot of fumes were coming out of the tank while pumping.
The scanner i use also lists the secondary air system, the EVAP system, Heated catalyst, and the AC refrigenant has red X's, but they weren't continuous.
View 14 Replies
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 Replies
My 1999 Camry - 4 cyc has a trouble code of P0136. Auto Zone told me it is a defective bank 1 sensor 2. As per the repair manual, the front passenger seat has to be removed to get to the sensor's electrical connector but an internet video shows that the driver seat has to be removed. Replacing the heated bank 1 sensor 2 on a Camry before?
View 9 Replies
Wife's 04 Escape threw the PO136 code for bank 1 sensor 2 02 sensor. Replaced it and light is off. Not convinced something else isn't causing it.
View 3 Replies
1997 f250 LD pick up 5.4L engine 131000 miles
Here is my story week ago code came on p0153 bank 2 sensor 1
Slow response ... now I been reading around and some people say bank 2 is passenger side other say it is drivers side or bank 1 is where cylinder 1 is , the point is I'm confused here for bank locations and sensor locations .....
View 3 Replies
