When I cut off the engine by mistake (shift slip ie ) the restart comes around but only after about 5 to 15 minutes . The last time this happened the car was at an intersection and this situation is getting dangeous.Why is the restart taking so long ?
View 2 RepliesI have a 2001 Nissan frontier SE the 6cylinder, no turbo, automatic transmission. My wife was not paying attention and thought the truck was running and so she put it in reverse and then realized that the truck as not running so she tried to start it while in reverse, when that didnt work she put it back into park and when she tried to start it, the cd player restarted and the wipers started and the guages peaked and whe truck made a fast ticking sound. i thought that it may have some how killed the battery but it does the same thing with the new battery in.
View 3 RepliesI have a '99 Frontier (3.3L V6) just had the radiator, hoses, fan clutch and 3 exterior belts replaced. Car's not overheating anymore, BUT, now I hear intermittently a "clack" (which sounds similar to a loud compressor when it shuts on and off). Car never made this sound before the repairs mentioned above were made.
I took pictures and could use finding out what the part is called that is making the noise. I see the 3 discs on the front side of one of the belt pulleys (i think?) spinning, then they will stop, making the clack sound. It seems to me that sometimes the sound is loud and then other times it is extra loud --are there two sets of these discs and the other set is somewhere I can't see?
2000 Nissan Frontier: Only when hot, engine knocks from center of engine on right bank. Not consistent, intermittent, goes away when revving above 3k rpms. Ever since: Preventative maintenance was performed: Timing belt, oil pump, water pump, valves machined and re-seated, new guides. Idle is smooth and slightly high on cold start up, no vacuum leaks seen. Manifold vacuum is only 15.5 to 16 in/hg, returning code of knock sensor (believe due to knocking). Not a rod knock, not a valve tap. Possible wrist pin noise?
View 1 RepliesI have a 2008 nissan frontier SE 4x4 with 71K on her. I'm getting two codes from my checking engine light P0455 and P0447. The gas cap is new and tight.
View 3 RepliesI have a 2004 Nissan Frontier pickup that I bought used in 2012. Shortly after I purchased it the the check engine light came on, would go off and back on. Last year (before inspection) I hooked it to the diagnostic auto scanner and it read the error as four oxygen sensors. The truck was running fine but in order to get it inspected I ended up changing all four sensors. The light came back on within the week (as soon as it rained) then would go off a few days later. Rain--on, then off. I managed to get it in for inspection on one of the days the light was off. So, now it is again inspection time. Light is on, still error on the scanner as oxygen sensors. Light has not gone off in a long time.
Also noting here that I have checked this error on several different scanners. The truck is running fine. Before I take it to the dealership is there anything else this could be?
I have a 2005 Nissan Frontier that recently had a new transmission and radiator installed due to a defect where coolant leaks into the transmission and destroys Nissan transmissions. After I got my truck back it ran fine for about 2 days, then on the third day I started it and the gauges all started going up and down at a speed of about 72 bpm. I shut it off let sit for a few minutes started it and it did this again. I repeated that about 4 times. I let it sit for about 4 hours started it and it was fine for a very short drive (1/2 mile). After about another 2 hours of sitting I tried to start and the battery was dead, my friend jumped it and it drove fine. So it sat for a few days until I had my brother jump it so I could drive to get a new battery. Once it was jumped the moving of the gauges started again.
As I was driving, the gauges kept coming on the going off. I got it to advanced auto and they replaced the battery, it started up drove it for a matter of minutes, then the gauges died and it wouldn’t drive faster than 1 MPH, then engine would rev when I hit the gas. I got it to a parking lot shut it off tried starting it the gauges would come on but as soon as I hit the gas pedal it would rev up but instantly the gauges would shut off and the engine would rev anymore. So I was stuck, got it towed to where the transmission was put in. They couldn't fix it but had to jump it to start it, so the new battery was dead. They towed it to a Nissan dealer and the mechanics are now saying it’s just a bad battery, but this just doesn't make any sense to me.
If after you shutdown a engine, and a fuel injector is leaking. Is there any sign to look for, that can pin point this problem.
View 1 RepliesI have a 98 frontier 4 cil. 4x4 manual transmission. The CE light is on telling me that the evap system needs work. I replaced the purge canister valve and now the light wont go off at all. You can clear it all you want, as soon as the truck starts the light come back on.The truck also runs rough, bucks at certain RPMS has no power and bad gas mileage. Within the last two years I have replaced; catalytic converter, fuel filter, plugs, wires, cap & rotter, transmission and clutch, air filter, cleaned the MAF sensor.
View 11 Replies2003 NISSAN Xterra
Problem started a couple of days ago. While driving the car normally it suddenly stopped. I was able to restart it but it turned off again 60 seconds later. This has gone on with the engine running from 10 minutes to 10 seconds. The battery terminals and all cables are clean. Distributor cap and rotors have been cleaned. Fuel pump replaced last night. I still get the problem. Error codes listed were: P0328 - Pre Detonation (knock sensor) Bank 1 causes could be restricted fuel - over temp engine. Now this error has been coming up for five years and I've replaced the sensor numerous times. P0732 - Gear 2 Incorrect RatioP0102 - Mass Air Flow Low InputP1148 - Closed Loop Control Function, BANK 1P0420 - Catalytic Convertor, BANK 1P0134 - O2 Sensor No Activity, BANK 1
Regarding Fuel Starvation - NOPE, Engine Too Hot (it wasn't), Second Gear Not Within Ratio (never had gear problems), Knock Sensor and most error codes have been related to bank one. Error codes on car computer were erased and engine is still hesitating slightly and stopping. Just checked Mass Airflow Sensor and it looks clean.
My 1990 Toyota Corolla which I hate to retire has only 64,000 miles on it. Starts and runs but while I am driving the dash lights up and the engine shuts off and won't restart. He thinks it is the NEC (?) switch but he said he is not really sure. Spending all that money and then finding out it is not fixed would not be worth it. It also is dangerous what if I am on the expressway?
View 19 RepliesI have a '99 Nissan Frontier 4cyl. p'up and the air conditioner kept going off. The truck has three drivebelts, all inline. The first is Crankshaft to the Power steering pump , the second goes from Crankshaft to the water-pump & the alternator and the third one goes to the air-conditioning compressor; the one that keeps coming off my truck & shutting down the A.C. I replaced it three times and the last time it went off within a couple of miles. I know the crankshaft and the A.C. compressor pulley's are out of line and believe that's my problem. A mechanic friend of mine looked at it and said he thought it was something called a belt-leveler that keeps all the belts from slipping off.
View 2 RepliesNissan Rogue SV 2011 is keyless entry vehicle. When using remote starter, the engine shuts off when brake pedal depressed and the car is restarted to drive away. does this 'turning off/turning on' the engine damage any of the systems of this vehicle. it just doesn't seem a good idea to have the engine turned off and then immediately turned on.
View 5 RepliesIt's a 2000 Frontier V6 4x4 CC with 104k miles. It just randomly dies going down the road. Sometimes it restarts. Sometimes it doesn't. Sometimes I just get a small blip (loss of spark or fuel - unsure which) when going down the road then it's fine again. It seems seems like a loose connection somewhere to me but I have checked and repaired everything I can find.
A little history of problems...
Fall 2014 - Fuel Sending Unit; I had similar problems a little over a year ago and I replaced this at ~90k miles. The stock one was corroded and the fuel pump wasn't getting power. Got the part from Nissan directly. Truck ran great for a year then started having same issues in fall of 2015. I am thinking this couldn't have gone bad again in only a year, but who knows? No engine codes at the time.
December 2015 - Distributor #1; I replaced it with one from Auto Zone. Had the same problems that day. Returned that and replaced with one from Napa Distributor #2 (New - house brand - supposedly made by Altrom - which is supposedly comparable to OEM) This seemed to fix it for a little while. At the same time I did the timing belt, spark plugs, wires, valve cover gaskets, a bunch of suspension work, etc. so I had the harness off. Did I knock something loose? I feel like I have checked it up and down.... doesn't seem that way.
January 2016 Bad Wire?; Same issues. Wiggling the harness into the distributor seemed to have an effect on restarting so I pulled the harness apart from the dist to the main and found a small cut on the casing of one of the ground wires. The wire was not damaged, just casing. Fixed that with a double layer of shrink tube and it ran fine again for a couple weeks. In this same period my catalytic converters also went bad. My exhaust manifolds cracked, next thing I knew I had catalytic converter codes on both sides of the engine. Ran it like this for a few months.
April 2016 Distrbutor #3 Same problem. Randomly dies. Gets progressively worse over a couple day period. I gave up and took it to a shop (Downing St. Garage in Denver, CO) They diagnosed it as a bad distributor so I had it replaced AGAIN (they were nice enough to use the Napa part I bought and get a free warranty part)
June 2016 Distributor #4 Same problem again. Still have not replaced cats - did not want to spend the money when the ignition problem seems un-related. Replaced distributor with another warranty part from NAPA. This time the one that I took off made a crunching sound when you turned it by hand.
August 2016 Finally replaced cats. CEL codes were gone for an afternoon then the truck started sputtering down the road again... CEL P1320 and CEL P0325 BACK AGAIN!
I am at a loss on what to do. I have read that the MAF sensor can get dirty... but this doesn't seem to explain the P1320. Anyway, I ordered some cleaner, a new knock sensor and another distributor (this time Nissan brand but re-manufactured... they no longer sell new ones.)
Our mechanic is stumped. The Frontier runs hot when idling. The clutch fan and thermostat have been replaced. The radiator has been flushed. When you are driving or you turn off the A/C, the temp goes down. The next suggestion is to replace the radiator, but I'm already hundreds into this so I hate to do anything else unless I'm pretty sure it is going to fix it.
We do know that the catalytic converter needs replacing. Could this have anything to do with it?
I have read two other threads that indicate a leaky head gasket for Nissan Frontiers overheating...but I'd like an opinion on my problem: I have a 1999, v6 3.3L, 4x4, manual Frontier that I have owned since 2001, always well-maintained, timing belt, water pump and thermostat already replaced a couple of years ago; currently has 129k mi. I rarely drive it (about once or twice a month).
Last time I drove it (I'm in AZ and heat was over 100 degrees) it started right up and was fine until I'd gone about 3 miles on the freeway doing about 65mph. Started to climb in temperature, but not into the red zone. I drove with it hovering just above the midway point (midway meaning perfectly normal temperature on my gauge) for a couple of more miles, when it started to climb just a bit more, I got off the freeway and dropped under 45 mph, the temperature went down to normal. I drove about 40mph back home and haven't driven it since.
I checked my coolant, which was extremely clean and not low, and was not boiling when I checked it soon after the temp went up on the freeway. What is the most likely cause?On a side note, since I do not drive it that often, what is recommended as to the gas that has been sitting in my tank since? How long does the gas stay good for? Further wondering how often it is recommended I drive it, for how long and at what sustained speed to keep my truck up and running?
I have a 2000 Nissan Frontier that is a 4X4 and has the V6 engine. Mileage is 172,000+. For a few years, I have had problems with the AC no longer cooling after I drive 20 or so miles and stop the truck, go in a store and start back up only to find that the AC will not cool after the stop. This seems to happen more when the weather is hot. Only once has it gone out without stopping the car and it was on I40 driving trough Oklahoma in 100+ degree weather. Once it quits cooling, after driving 20 to 30 minutes, it usually starts to cool again. It sometimes speeds up the process if I roll the windows down.Coolant levels are fine.
So...is there a faulty sensor somewhere? What could it be that is the problem?
We have a 2003 Nissan frontier pickup (automatic).The AC recently stopped cooling, but the fan works. It was cooling perfectly great when all of a sudden, it stopped. If we turn the AC on, the compressor (I'm guessing) starts to click and continues to click until turned off. (started to grind under hood). It's not a rattle, definitely a click as if it wants to turn on but can't make the electrical connection. It kind of sounds like when a starter has gone bad and it clicks. Except, it does it repetitively until turned off. This doesn't happen if we turn on the fan but leave the AC off. Does it sound like the compressor went out? How can we troubleshoot it?
View 19 RepliesI have a 2000 Nissan Frontier that is having issues. I had the distributor replaced and the knock sensor. The day I got it home it started having a weird starting issue. It has always started first crank super easy & strong. Runs GREAT.
When the truck is cool it starts right up but, when I've been driving around for a bit and turn it off, if it's a short stop starts right back up, some hesitation. If I stop for 15-45 mins it doesn't want to start. I can crank it all day and it wont start and gives a little kickback, if I crank too much the engine will smoke a bit, spits and sputters when you turn the key off. The longer it sits before I try to start it the worse it gets... around one hour is the worse. - Finally figured out if I try cranking it over several times, turn off the key and wait literally one to two minutes it starts right up super quick and strong just like when it's cool. So random and weird.
No warning lights & Nothing shows up when hooked up to the computer, fuel pump checked out OK.
I have some serious vibration at about 40 to 50 MPH only when the accelerator is depressed. As soon as I let off the gas it stops. I have had the tires rotated and balanced and the U joints checked. My Mechanic says he can't figure it out and to drive it until it breaks.
View 3 RepliesMy 2005 Nissan frontier reeks badly.
Has new air filters and new cabin filters. Only seems to smell when driving at 55mph for about 20 minutes, the funk comes from the vents and in all heat/AC and fan modes seems to be less stinky in the winter.
Nothing is dead in the heater box because it does not stink in when driving around town and I have poured gallons of Lysol down the air intake during recic, open vent, etc, Smells like a mix of eggs, oil, and funk.
Dealership says it is not the catalytic converters as they "check out fine" Nissan dealership says it's bad gas, which is unlikely as when I drive away from home and I use other gas, it still smells.so what is it? What is it?