Right Front Tire has excessive wear on Right INSIDE and car was pulling to the left. I rotated (or is it revolved?) my tires, and now the pulling has stopped......
OPINION: Bad tire that just wore poorly? Slight alignment issue that caused tire wear that then caused car pull? Wheel bearing issue causing tire wear? Or something else?
Having issues with excessive front tire wear? I have had the alignment checked by two VW garages and a third party garage and all of them confirm that the alignment is good.
The VW garage also confirmed that as far as they can see there is no suspension issues, but the excessive wear on the front tires indicates that something is wrong.
I have owned the car since new in 2008 so know it has a clean history no accidents.
Both front tires look like this.....
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 RepliesAbout 5K miles after putting on 18x8.5 rims with 235-40 tires noted bad reverberating droning tire noise and noticed stairstep pattern of excessive wear on inside tread blocks, equal on all 4 wheels. Is this just from going from OEM ET47 to ET35? Is camber adjustment indicated and is camber adjustable also on the rear wheels? (Of course, noise and reverberation gone when OEM wheels put back on)
View 5 RepliesI just had the tie rods replaced and a front end alignment on my VW Golf. The tires that were on the front were moved to the back because of some wear on the inside edge. The tires currently on the front look brand new, but the car pulls to the right more than it did before I had any of the work done. The place where I got the work done told me I would need to replace the two tires with wear but they are still in mostly good condition. They are telling me now the pulling is because the tires on the rear have wear. Can wear on rear tires really cause my car to pull so significantly to the right? The tires are only two years old. I do not want to replace them yet. The car front wheel drive.
View 2 Repliesrecently I replaced the front rotors and pads on my 02 Saturn SL2. I did this because there was a grinding sound coming from the front left wheel well and I had noticed a band around the rotor that looked gouged. All in all, about 30 minutes of work, following the Hanes manual. In the course of disassembling the front left caliper, I realized that the cause of the gouge in the rotor was from one of the tensioning clips on the caliper bracket. One of the flaps on the clip had bent back and was causing both the grinding sound and the gouge in the rotor. So naturally, I replaced all the tensioning clips as well. After putting everything back together, I took the car on a quick test drive around the block. The noise, while lessened, was still present. Furthermore, after I got to work this morning, I noticed that that there is the start of the same wear pattern on my brand new rotor.
What could be causing this problem to reassert itself?
It's a 2004 Honda LX... We bought a car that had previously been damaged to the right rear. They had fixed it up and all. When I got it, the car was already pulling left so I eventually took it to get an alignment.
After the alignment the technician told me that it still might pull because of how the tires were worn - and it still pulled left.
This past Saturday I decided to get a lot done: 4 new tires, an alignment, break pads changed, and the rotors were resurfaced.
I tested the alignment on the freeway and local flat roads and it still pulls left.
I'm thinking this problem still has to do with the previous damage, which parts could be causing it so I can pitch it to the shop I'll be taking it to?
Had my tires rotated yesterday and now the car is pulling noticeably left. On a flat road, if I let go of the wheel I change lanes in about 3 to 4 seconds depending on speed. Also, the faster I am going, the worse the pull feels. Before the rotation, the car would pull very slightly to the right sometimes but only enough for me to wonder if it was pulling or if it was my imagination.
One other detail, the tire that is now on the left front is newer than the others due to a pothole eating the last one. It is the same hankook tire in type and size. Just with less miles on it. It was previously on the front right. I've seen the threads on the pulling issue and the 18 step TSB and all of that but nothing about rotation or the pulling following a specific wheel or tire. Could the rolling resistance of a newer tire really cause that much of a pull?
My issue is I am getting ready to leave for a road trip and can't get in for an alignment or for someone to go through the whole TSB. I think I might switch the 2 front wheels.
I notice that my front passenger tire is getting some inner wear on it. The tire doesn't even have 5k on it. I know I should get an alignment that's a must but is there something that might be wrong with it anyways since its just the front passenger?? Balljoint, tierod end and etc?? I don't really have a local auto shop that I trust 100% so I don't want them to be like, there is 3 balljoints out and etc. I had the inner tierods (both) and a few balljoints fixed last year and then got an alignment done. Any tips??
View 4 RepliesI just bought a used 2007 Santa Fe Limited. It has 78,000 miles on it. I have gone bumper to bumper looking for problems and am pretty happy about the condition. HOWEVER, I have noticed a shuddering/bobbling, fairly faint, when going over slightly rough roads a low speeds. The tires are shot. But they are all exactly the same ... meaning the same wear more so on the outside. I believe they were rotated properly, but something is wearing the outside prematurely. Is the shuddering/bobbling the culprit? What is the most common issue for the Shuddering/bobbling at low speeds on slightly rough roads?
Next, I want a quiet ride. Handling is not a concern. Should I go with a slightly wider tire or slightly taller tire? Lastly, I need new mats. I want them to be the same as what came with the car. Do I have to go to the dealer or are there some vendors with better deals on factory mats.
Any 1 have their tire that have uneven tire wear? Mines is Dunlop and my front right tire has uneven wear on the outer thread. All other tire don't have uneven wear. I'm getting new tire for all 4 rims and check my alignment. My gs is a f sport rwd.
View 3 RepliesI have am 01 6.8 two wheel Limited. about 150K. My question is about both the front tires having more wear on both the inner and outer edges. The inner is a bit more but not by much.
I have been keeping very close track of my air pressure because I know the usual suspect is low air pressure but I am running 75psi and the max sidewall reads 80psi. I have never had it below 72psi. The truck tracks and steers down the road very nice with no drift or pull to either side. wheel balance is good.
Front end align is good. I have no issues with how she drives down the road. Everything seems to be checking out to be in spec..?
My '02 Ranger has had tire wear for a while now, and its on the inside of both front tires. I was thinking it was either toe or camber, or maybe both. I havent been able to get an alignment recently. If its the camber, should I get the camber kit from Ford?
As for the squeaking, it first happened last summer, and I sprayed WD-40 on the upper control arm bushing and it went away until last week (obvoiusly temporary). Now its back. Also happens while turning the front wheels.
2014 FX4 F. Got 6000 miles on the truck, front tires are wearing on the outside edge, and also when turning the wheels to the max in either direction I get a loud creaking sound,??
View 14 RepliesI realize that is vague. I realize it could be anything from a wheel bearing to a ball joint, tie rod, control arm/control arm bushing, etc.
Are there any very common front-end steering or suspension issues on 2012 escapes? When tires are inflated to 32-34psi, the car tracks straight, gets great mileage --but almost sounds/feels like it's got a CV or wheel bearing issue on the front right. Every time I hit the brakes while backing out of the driveway I can hear a slight bump or pop. When the car is parked (flat, tires straight) there is slight play left-to-right in the steering wheel.
I'm a German car guy. Have never touched this car. (Wife's car) Right tire is wearing bad on inside. Looking for some direction so I can assess. Car has 88k miles. This will be a DIY fix. Don't have any manuals or anything so just looking for a heads up where to start. Also is Haynes the best way to go? Is there a Bentley? Anything online/CD/DVD?
Play in steering wheel makes me think tie rod (fine because easy/cheap) but such excessive wear on the inside right front makes me think wheel bearing. Could it be both? This is AWD. Is this (like a Subaru) a CV joint where the front spindle passes through a strut base that everything attaches to --so there's an inner and outer wheel bearing?
Does anything up front require a press or can it all be done without a press?
I have a 06' Ranger 2WD with General Grabber tires that have about 30,000 miles on them and still show significant tread remaining.
Within the last 2 months, I have experienced excessive tire noise - like I am driving a Humvee or something. Also, when I turned right or left the tires would make even MORE noise - it seemed to be coming from the right front tire mostly. 2 weeks ago I had the tires rotated and the sound seems to have reduced while turning but I still have the howling Humvee noise while driving down the road. There is no vibration coming from the wheel, so I don't think it's a balancing issue. Could it be the bearings?
I also checked the PSI all around and one tire does have a slow leak but I try to keep to topped off.
I've been using the EV mode - the EV portion of the curve without pushing the EV button - to run around town and to maintain speed once I've accelerated to traffic speed. It really boosts the mpg numbers and I'm able to get 55-60mpg on my 47mi. Roundtrip mostly highway commutes (hills included). Without the running in EV it's probably 42-48mpg.
View 8 RepliesI replaced the front brake pads and rotors on a 99 Bonneville about a year ago. The outside pad on the passenger side has worn completely out and has ruined the rotor. The inside pad on the same side looks fresh. Everything on the driver's side looks good. What the heck happened? I am not an expert but I have replaced many of these GM brakes and have never seen this result.
View 11 RepliesI have had a Clicking noise on my 2000 x 4x4 since 6 months coming from the front right side tire noticeable over rough roads or over bumps and I went on a journey starting with ford dealer to almost all well recognized service centers and every body says your front suspension is ok and no one seems to know where it is coming from. I thought it was my hub bearing since it fails almost every year but when I was changing the bearing, I noticed a big Excessive play in axle.
See video : My AXLE Shaft - YouTube
Also I noticed oil mixed with grease the grease is prawny with a reddish sort of color or that is some thing else.
See photos ....
Any way after replacing the hub Bearing with a used one and butting every thing together I went on a test drive. Noticed that the vehicle drive line is not right the car seems to wonder and the noise still there so i didn't get far i came right back and park my x then a funny burned oil smell was present.
Is it some thing i did wrong or is it bad situation gone worst ?
Items Checked Or Replaced In The Last 4 Months ( trying to fix)
Tie Rods. Ok
ball joints. Ok
suspension front and rear. Ok
Front stabilizer bar. Ok
control arm bushings. Ok
stabilizer bar bushings Ok
steering linkage. Ok
brake pads. A new front set installed
Rotors . Both front changed with oem parts
body mounts + sub-frame mounts. Some replaced
shock absorbers . New 4 set installed
- Rear Monroe 911176 Reflex Light Truck Shock Absorber
- Front Monroe 911175 Reflex Light Truck Shock Absorber
tires. Replaced with a new set off four
Hub Bearing. Second hand (that's when I saw it)
Spare Parts waiting list (Ordered):-
O ring ord part # 4C3Z-1K106-AA
(knuckle seal) (F81Z-3254-CB).
and some other dust seals which i can't recall.
I am looking for how to fix axle play and get red of the noise. (this is a video from you tube for clearance)....
F250 wheel bearing, is this bad or not? - YouTube
My 18 inch Conti Contacts have approximately 20,000 miles on them. The tires are not wearing evenly and have excessive wear on the outside portion of the tires. The dealer says that they spoke with VW and VW says that it is "normal" for the tires to wear this way because of the "turning radius" of the vehicle. I smell BS. I don't know much about this subject but it would seem to me that the tires should wear somewhat evenly if the vehicle is balanced and aligned properly.
View 6 RepliesAt my wits end on this. Left front brake is pulling ever so slightly on my '02 RWD Sport Trac. Just enough to annoy the crap out of me. Sometimes I hardly notice it. Over the past year or so I've flushed and bled the lines after replacing rear wheel cylinders, rebuilt the front calipers and replaced the rotors and pads. It's still pulling. Is there some electronic adjustment for the module that the brake lines come out of? Does the ECM control the pressures?
View 5 Replies