2014 FX4 F. Got 6000 miles on the truck, front tires are wearing on the outside edge, and also when turning the wheels to the max in either direction I get a loud creaking sound,??
View 14 RepliesI have a 2014 Supercab Ecoboost F150, which has 37k KM on it (23k miles). I work at sea for 4 weeks on / 4 weeks off so the truck sits a fair bit. I had it in the dealer for scheduled servicing and they noticed the inside pads on both front brakes were wearing significantly more than the outside (4mm vs 7mm). The lube guy at the time had suggested sticking calipers and that they'd be warranty.
A few days later I brought the truck back in to have the brakes looked at and an unrelated warranty item done. They looked and said the calipers aren't sticking and the rotors are grooved and rusted, particularly the inside surface. They wanted to put new pads on and turn the rotors for 400 bucks.
I had a hard time believing it wasn't the calipers, and I was having a hard time getting a good explanation from the service writer of what was going on. So I took the truck back and pulled the pass side tire off in the driveway to take a good look.
As far as I can tell, the calipers are free. The slide pins are nicely lubed and are free, and the pads are free to move in the anti-rattle clips. I squeezed the piston back with a set of C clamps and it seemed to be good. Also, the pads are wearing more or less evenly (not tapered or anything), just the inside is worn significantly more than the outside.
So, rotors wearing out in 23k miles? They aren't really warped, just heavily grooved. My theory at this point is that the weeks the truck spends sitting allows too much corrosion to build up on the rotor, which is getting caught up and wearing down the pads and rotor. Maybe the outside of the rotor isn't nearly as bad because it gets hosed down and washed more frequently?
Inside rotor surface
Outside rotor surface
Inside pad surface.
I still have 7 months of bumper to bumper warranty. Ford says the only cover brakes if the damage is caused by a caliper, so I think I'm out of luck on that front.
I have a 2003 Toyota Camry XLE that has had the following issues.
1) When going over speed bumps you can hear a very loud creaking in the front and rear and occasionally a clunk in the rear.
2) When driving on rough or bumpy roads you can hear a metallic chattering coming from the driver's side.
3) There is a vibration in the car that I can't pinpoint but I was told the front rotors are slightly warped and that could be causing it, thoughts?
4) I put brand new tires on in January and it has less than 10,000 miles on them but they already look like they need to be replaced. They are Michelin Hydro-edge tires. I have had it balanced/rotated at 6,000 miles as well as an alignment. Nothing was said to me about any problems by the tire place when I had it done a few months back, which I find odd.
5) When turning into parking spots or turning at low-speed in general, especially when turning right, I sometimes hear the tires squealing.
I was going to go ahead and replace all 4 struts, strut mounts, strut boots, rear sway bars, all 4 rotors and brake pads. But I wanted to make sure that this would fix the problem.
Do I need to get the front Driver/Passenger CV Half Shaft Drive Axle assemblies? Are there any other parts that need to be replaced that could fix the issue? (Tie Rods? Ball Joints? etc?) Are there any other parts you'd recommend replacing while working on the car? I tried searching but could not find anything that specifically matched the problems.
I own a 2010 Toyota Corolla S that I purchased with about 30k miles, I have put about 65k on it since purchasing it. When applying the brakes in dry conditions I am receiving what feels like the abs engaging and a loud pulsing sound/creaking sound. The brakes will pulsate as if I am stopping on snow or ice but no traction control or abs lights will not illuminate. This has been happening for a good while(ever since I purchased the car). I have replaced the front rotors and pads and the problem purists.
The road conditions in this video are completely dry with an outside temperature in the high 70's.... YouTube .....
Ok haven't been on here in a LONG time. Sold my '12 and bought a DRW '14 F350 to tow our fifth wheel. Just got back from a 775 mile round trip pulling our fifth wheel. My dad noticed my passenger front tire was going bald on the outside. I said yeah it was pulling to the right and thought my tire was low but when I checked it was the right psi.
Turning to the left I was starting to get a grinding type noise. If I rolled my passenger window down you could here something just grinding away but when you straightened out nothing.
So I took it into the dealer and they tell me the outside tire wear is normal. I said it has 22,000 miles and the passenger tire will be bald on the outside in 4,000 more miles or less. Said they can't hear any noise, yet my wife can hear it, kids can hear it and people outside the truck can.
It's not normal for the passenger or drivers tire for that matter to go bald in less than 25,000 miles? Tires have always been kept to proper psi, I've towed only about 5,000 miles total with it. They are also taking the worthless rancho rebranded shocks off and going with bilstiens. I should have replaced them 10,000 miles ago. They are horrible shocks.
It really torques me that they have it for a week and can't find anything wrong. When turning to the left it's almost like bump steer in 4wd just not quite as bad but with also a grinding sound that you can hear inside the cab and can feel it in the floor board. Nothing evident but just looking under the truck.
I have am 01 6.8 two wheel Limited. about 150K. My question is about both the front tires having more wear on both the inner and outer edges. The inner is a bit more but not by much.
I have been keeping very close track of my air pressure because I know the usual suspect is low air pressure but I am running 75psi and the max sidewall reads 80psi. I have never had it below 72psi. The truck tracks and steers down the road very nice with no drift or pull to either side. wheel balance is good.
Front end align is good. I have no issues with how she drives down the road. Everything seems to be checking out to be in spec..?
My '02 Ranger has had tire wear for a while now, and its on the inside of both front tires. I was thinking it was either toe or camber, or maybe both. I havent been able to get an alignment recently. If its the camber, should I get the camber kit from Ford?
As for the squeaking, it first happened last summer, and I sprayed WD-40 on the upper control arm bushing and it went away until last week (obvoiusly temporary). Now its back. Also happens while turning the front wheels.
I own a 2011 lariat with 500 miles. We have had several days of rain and I am getting alot of rust spots on my driveway always below and inside the right front tire. None in the rear or left front. Dealer said not to worry about it after they looke at the area. They said it is the new metal forming surface rust. There is a skid plate which seems to cover wherever the rust is starting. Should I demand that area be undercoated.
View 3 RepliesI realize that is vague. I realize it could be anything from a wheel bearing to a ball joint, tie rod, control arm/control arm bushing, etc.
Are there any very common front-end steering or suspension issues on 2012 escapes? When tires are inflated to 32-34psi, the car tracks straight, gets great mileage --but almost sounds/feels like it's got a CV or wheel bearing issue on the front right. Every time I hit the brakes while backing out of the driveway I can hear a slight bump or pop. When the car is parked (flat, tires straight) there is slight play left-to-right in the steering wheel.
I'm a German car guy. Have never touched this car. (Wife's car) Right tire is wearing bad on inside. Looking for some direction so I can assess. Car has 88k miles. This will be a DIY fix. Don't have any manuals or anything so just looking for a heads up where to start. Also is Haynes the best way to go? Is there a Bentley? Anything online/CD/DVD?
Play in steering wheel makes me think tie rod (fine because easy/cheap) but such excessive wear on the inside right front makes me think wheel bearing. Could it be both? This is AWD. Is this (like a Subaru) a CV joint where the front spindle passes through a strut base that everything attaches to --so there's an inner and outer wheel bearing?
Does anything up front require a press or can it all be done without a press?
I bought a 2009 F-150 King Ranch a few months back. It has 125k miles on it and the only aftermarket thing on it is some larger tires. I love the truck but twice now (at two totally different driving instances) I have started hearing this bad sounding tap in the engine. The majority of the time it has ONLY been when I am in drive or reverse. I can especially hear it if I am going through a drive through. Anyways as I was backing into a parking space today it started making an even louder tapping sound. I recorded it and have provided the link to youtube..
It continued to make this terrible sound until I revved it slightly and then it went back to normal idle. This all started as I was in reverse backing up but this is the first time it has continued even into neutral. Really hoping for not terrible news on this. Ive read about the cam phaser issue and nothing has been done to those yet. It is the 5.4L and a 4x4. How to fix this and not have a clunker for a truck...
Here is the link to the youtube video of the truck running... it was too large to be uploaded on here : [URL] .....
Having issues with excessive front tire wear? I have had the alignment checked by two VW garages and a third party garage and all of them confirm that the alignment is good.
The VW garage also confirmed that as far as they can see there is no suspension issues, but the excessive wear on the front tires indicates that something is wrong.
I have owned the car since new in 2008 so know it has a clean history no accidents.
Both front tires look like this.....
I notice that my front passenger tire is getting some inner wear on it. The tire doesn't even have 5k on it. I know I should get an alignment that's a must but is there something that might be wrong with it anyways since its just the front passenger?? Balljoint, tierod end and etc?? I don't really have a local auto shop that I trust 100% so I don't want them to be like, there is 3 balljoints out and etc. I had the inner tierods (both) and a few balljoints fixed last year and then got an alignment done. Any tips??
View 4 RepliesI have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.
Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 RepliesSo due to a puncture I got earlier this week, I had to buy a new front passenger side right tire. Now the car pulls very slightly to the right. Is this due to having about 6k miles on the left tire and a brand new right tire or do I need an alignment again?
View 2 RepliesI have 3 new tires and 1 with wave or cupping wear. It is a new tire not even a year used. I went in to get my alignment fixed because I was told the cupping is due to car being out of alignment. They told me I have to replace the tire with the cupping wear on it before they do the alignment. Is this true? or can i keep the tire and not have to shell out more money for a tire that is not even a year old. that being said, I am now doing more research and realizing that cupping is actually due to problems with the shocks. not alignment.
It's a 2009 toyota matrix xrs....
I purchased the 2010 corolla back in October of 2010 and never noticed until almost 2 years later that all of my tires were inflated to 62 PSI.
I went to the dealer and they didn't know anything, I myself didn't put any air into it nor did my brother who drives the car too. However he has always complained that the ride was stiff.
Iam wondering if it cause my engine to wear out faster since the tires were so stiff and it bumps when going over pot whole. I could be 100% certain I drove it off the lot with 62 PSIs.....
I just bought a used 2007 Santa Fe Limited. It has 78,000 miles on it. I have gone bumper to bumper looking for problems and am pretty happy about the condition. HOWEVER, I have noticed a shuddering/bobbling, fairly faint, when going over slightly rough roads a low speeds. The tires are shot. But they are all exactly the same ... meaning the same wear more so on the outside. I believe they were rotated properly, but something is wearing the outside prematurely. Is the shuddering/bobbling the culprit? What is the most common issue for the Shuddering/bobbling at low speeds on slightly rough roads?
Next, I want a quiet ride. Handling is not a concern. Should I go with a slightly wider tire or slightly taller tire? Lastly, I need new mats. I want them to be the same as what came with the car. Do I have to go to the dealer or are there some vendors with better deals on factory mats.
Right Front Tire has excessive wear on Right INSIDE and car was pulling to the left. I rotated (or is it revolved?) my tires, and now the pulling has stopped......
OPINION: Bad tire that just wore poorly? Slight alignment issue that caused tire wear that then caused car pull? Wheel bearing issue causing tire wear? Or something else?
Today I was out getting lunch in my Ecoboost When it started making an extremely loud grinding noise from the front end of the truck. My first thought was I blew a turbo. After holding the break and building boost I discovered it was not the source of the noise. Also the truck runs perfect and there is no smoke. I then took it to my friends auto shop and pulled both front tires off to check and see if anything break related came loose. We found nothing. The noise only happens upon acceleration or cruising throttle, as soon as you let off the sound goes away. So after I found nothing I took it to ford and what would cause that, but they assured me that they would have my truck for a long time while they figure out the issue.
View 14 RepliesI'm having some strange action in the turn where sometimes it "sticks" and also I sometimes get a loud whining sound for 10 seconds or so and I believe it's coming from the power steering but I could be wrong.
I know my ecoboost has an electronic power steering system but that's the extent of my knowledge on it. Does it have a pump anywhere in the system that could be making this whining noise?
124,+++ miles, no real issues, runs like a champ.