2000 Chrysler Sebring Convt quit while driving. Tow truck drive and a mechanic at scene of breakdown felt itt seemed like it wasn't getting gas. Replaced fuel pump, fuel filter, 2 sets of plugs ans it won't start and when it did it ran rough and then fouled out new set of plugs. Seemed like too much fuel going to cylinder.
View 1 RepliesMy oil light comes on when I stop but goes off when I'm driving. I check the oil level and it was fine. What would cause this? It's a 2001 sebring 2.7L
View 6 RepliesI have a 98 Sebring Convertible 2.5L V6 that stalls after 10 minutes of driving at 30mph or even at highway speeds (ouch), but it seems only if the car has been sitting parked for 5 days will the stall occur. If I drive it daily/every other day, she seems to run just fine. Somewhere in between 2 and 5 days, there is sometimes a surge at that distance, but not a complete stall. The stall has been a very specific distance that if I let the car sit for 5 days, I can essentially pull over in anticipation of the stall. When the car stalls, the dash gauges all go to 0 and lose all power steering, but headlights stay on. Otherwise, there's been no noticeable loss of power, rough idle or anything else to indicate a problem. There are no codes on the computer. The stall happens once. I can pull over and immediately restart my car and be on my way without experiencing another problem until I let the car sit for 5 days again.
View 2 RepliesI have a 2004 Sebring my check engine light is on and the RMP's are really high while Im driving. What could be going on?
View 11 RepliesI drive a 2002 Chrysler Sebring convertible with about 130,000 miles on it.
I was driving down the highway in early November when the check engine light came on my car. I took it to Aamco who did some diagnosis and replaced a solenoid assembly in the transmission. The light went off and I was on my way. I never got the exact code.
About a month after that, the light came on again. This time, I got a low end code reader and scanned it myself. I got a "P0700" code, which I've read is a generic code that the transmission system sends to the computer or something. So I used my reader to erase it. However, the light came on 2 days later while I was driving down the highway at about 70 MPH.
So I went to an auto parts store to get a more detailed scan with a better tool. This one came up "P0740 Torque Converter Clutch Solenoid Circuit".
This feels weird, because the solenoid assembly was just replaced a month ago (and is still under warranty).
The car seems to drive okay. I don't notice any actual problems in shifting. The tachometer seemed to get up to about 3000 RPM on the highway. But I've seen practically new cars do that. The last time I had serious transmission problem it would rev up to about 5000 or 6000 RPM on the highway and still only getting up to about 40 MPH. That was 3 years ago and at the time I had a fairly expensive transmission repair (which included a new torque converter).
But like I said, the car seems to be driving okay. I don't drive much. Maybe 100 miles a week? And even that is mostly optional in town driving. I'm not looking to keep this car for more than another 20,000 to 25,000 miles though for the time being I cannot afford a new one.
What are the possible causes here? What are the consequences of ignoring this? Like I said, it's still driving fine and as the old saying goes "if it's not broke, don't fix it".
image.jpeg3024x4032 2.6 MB
I was driving down the road for about 20 minutes. When I saw steam coming out. I was a block away from home so I thought I'd make it before anything bad happened. The light turned green and I hit the gas and a few seconds after that something popped. I continued driving and the engine screeched and I pulled into my driveway. I jumped out and opened the hood and there was coolant everywhere. Like covering the engine and the underside of the hood.
2002 Chrysler sebring...
Check engine light comes on, car starts "chugging", recovers, chugs, recovers. So we limp to our destination. Check engine light goes off after car stands overnight. Repeat after driving car again. Mechanic replaced a 4" square "switch" somewhere "hot" last time. Said heat makes it go bad. Can't find anything 4" square under the hood. Mechanic says this part goes out all the time on this model and year.
View 6 RepliesI have a 2002 Chrysler Sebring with 116,000 miles and over the past month the engine has shutoff as I am driving and once I park turn the key off and turn on it has started to run again. This has happened about four times and each time it has been difficult starting it after the car has stalled. The most recent time this happened when I went to restart the car, a grinding noise became apparent. The last few times that I have started the car the grinding noise would be heard only to ultimately fade away in about 15 seconds. The check engine light came on and went to get the code and it came back suggesting a problem with the camshaft position sensor, but I don't fee the noise is related to that.
View 1 RepliesI have a 2004 Chrysler Sebring with a 2.4L dohc and automatic transmission with 115k miles. I recently had the timing belt and water pump replaced. Shop left the front 2 engine mounting bolts off and the rear one loose. Picked up car after business hours drove it that evening and kept hearing a strange metallic squeak.Returned it to the shop the next morning and as i was driving it began to smoke and stall with the temp gauge pegged. They had also left a hose to the heater core disconnected. Could the engine not being mounted to the chassis and/ or the overheating have damaged the transmission.
View 3 RepliesGot a bit of a problem with my car. Earlier this week, I got in and noticed there was heavy condensation on the inside of the windshield of my 2002 Chrysler Sebring convertible. The windows had been rolled up and the top up of course. I see this kind of condensation happen on the outside a lot in the mornings. You know, dew settling and all that. If I wait around until later in the day, it evaporates on its own.
Anyway, this time it was on the INSIDE. I wiped it clean easily enough and was on my way.
Today I noticed that my heater wasn't working. The temperature gauge goes up to about 1/3 of the way, so I know the car is warming up. I'm not sure if it normally goes up that high; I don't usually pay much attention to the temperature gauge.
I have an '06 Sebring convertible, 2.7l, V-6, 58,000 miles. When stopped with A/C on, car tends to surge. When I put in neutral, surging stops. Also, I sometimes get a "thump" (with both sound and feel) like I've been rear-ended, but have not. Dealer did tranny serivce and replaced all plugs and 2 coils which they said were "arcing". Did not fix problem. What would be wrong with A/C so as to cause this?
View 5 RepliesI have a 2002 Chrysler Sebring that broke down. Unfortunately it ran out of oil, and I was told that the car has 2 sensors that detected the lack of oil and shut down the engine. A local auto repair shop replaced the sensors. I paid the bill and began to drive the car home but I only got 20 miles away when the engine blew. My question is, if the the shop told me the car was fixed and then the engine blew, aren't they somehow liable for this?
View 19 RepliesI recently brought my 2000 chrysler sebring in because the alarm was going off at random times (3:00am). Also when I was driving the interior lights would turn on and off and the dash readout would say "DOOR" as if I had opened the door, there was a relay clicking sound under the dash and the car would also try to relock the doors. This was an intermittent problem, occasionally the car would be fine for a while then the show would begin. I took it to a local Chrysler dealer and they diagnosed the problem to be the BCM or Body Control Module.
My conclusion is that this whole problem was caused by a shorting door switch and that either they misdiagnosed the problem and when the new BCM did not fix the problem they found the real problem in the door switch or they just scammed me from the start. I think the "part exchange program" is a scam. Why don't I get the part back or why don't I get two prices, one if I exchange the part and one if I don't.
Could a faulty driver door switch damage a BCM? (I never heard of this before. In fact another dealer told me all he needed was the VIN to see if the part was in stock).
My daughter's 2001 Chrysler Sebring began "shaking and jerking" last night. She described it as similar to when a person drives a standard transmission that doesn't know how to do so. (Her car is an automatic.) She had been driving it for about ten minutes without a problem and had luckily just turned onto a residential street to pick up a friend. She said the check engine light came on as well. She was able to limp it to her friend's and leave it parked there.
Recent work on the car includes the thermostat being replaced and a resistor related to the heater blower motor being replaced. What might be causing this. She's probably going to have to have it towed.
ASD Fuse keeps blowing. I unplug PCM and fuse no longer blows. I plugged in pin 41-80 and the the fuse is still ok. Car just quit running and starter will not turn. Does pin 1-40 control starter and fuel?? Could I have a bad PCM??
View 2 RepliesI have the above mentioned 2005 Sebring Convertible (2.7L V6, Touring) and the AC will work occasionally, but when it is hot and humid, it is sure to blow hot. First up was to check the system pressure and top off if needed - not the problem. Also blew the bugs and junk from the radiator fins. The wires and electrical connections look good at a glance. Turning the car off and on again doesn't work. Why would the darn thing work part time and take days off when we need it most?
View 1 RepliesOil light comes on when I stop and goes off once I move again. Oil is full and just changed. What causes this & can I repair? I have a 01 Chy Sebring withh 100K miles on it. I bought new & have changed the oil every 3K miles since I have had it.
View 7 RepliesI have a 2008 Sebring convertible that has starting issues. Sometimes when I turn the key to start, it does nothing (no noises, maybe a small click very rarely). If I take the key out and put it back in, it may start. Usually, I have to turn the power on, move the gears, and try again. Sometimes, it will start immediately, or I may have to do this procedure several times. It has been taken into the Chrysler dealer twice. They said it was not the switch or alternator and replaced the battery that wouldn't keep a charge. It was a 5-yr battery with 3 years of use. I was told to drive more! I shouldn't have to charge the battery every day. Several diagnostic tests were performed with no results. It still did this twice after the battery was replaced. Could it be cables?
View 3 RepliesIn May 2011, I got into the passenger side of my 2006 Sebring to find the foot area full of water, and it wouldn't stop pouring in. So I had work done on the AC unit to fix a broken plastic part on the firewall. I am a snowbird who travels to Florida every fall, and subsequent to that work being done, I have had to have a line (?) cleared because the water drips into the driver's side when I turn right. After clearing the line, it seems to be ok. This year, I had the line cleared and the problem persisted. My mechanic cannot figure out what's going on.
View 2 RepliesIts a 1998 chrysler sebring jxi. 2.5 V6... It runs fine then randomly shuts off all electrical parts stay on i have to pull over or if it turns off at a red light let it sit for a while because i immediately get the "no bus" code. i have to let it sit with the car on but not trying to crank until the code goes away then it cranks again. sometimes i have to repeat that process a few times, sometimes just once. at times the code only last a couple minutes but sometimes over 10!
View 10 RepliesI've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.
View 2 Replies