Subaru - Outback :: 2006 - Radio / AC And Blower Went Out At The Same Time
Oct 15, 2011
2006 Subaru Outback
I am driving along and my radio go silent. the AC & the blower go out at the same time. I drop off the car in to the Subaru dealer in Steamboat Springs, Colorado. they call me back in a couple of hours and tell me I have bad radio that might work for a while longer but they recommend replacing it. $350 plus tax & labor.
I get the car back and the scan button no longer works & the buttons stick. does this seem right?
View 2 Replies
Advertisement
Just the other day the radio in my 06 Subaru Outback lost the ability to pick up an AM stations. Is this going to be expensive?
View 8 Replies
A new issue has cropped up with my 2001 H6 Subaru Outback (which I believe is technically a Legacy). We've put so much work into this thing to keep it running and this might be the last nail in the coffin. However, what's going on...
My wife reported to me yesterday that the vehicle was turning itself off while driving. I was not in the car to verify any of this, so this part is anecdotal. After 45 minutes of driving, she said the engine was "hiccuping" and the gages were dropping to zero and then bringing themselves right back up to the current RPM and speed. She said the ABS light came on. The first time the vehicle did this, she reports that it did it many times in rapid succession. She described it as "the gages were going crazy". After turning around to come back home this happened once more, though not in rapid succession. It was a single occurrence of turning off and back on again. She indicated that the vehicle did not require a restart with the key. I suspect that this was because she was driving at highway speed at the time.
She brought it right to the mechanic and - as is the case with all intermittent issues - they were not able to repeat the failure in any way. So, being an engineer, I decided I wanted to experience it for myself and do a few tests.
Today I drove 45 minutes to work, 10 minutes of small town driving, 25 minutes of highway driving, 10 minutes of small town driving. Lucky for me (!), in the first five minutes of driving, the radio cut out, power steering died, and I heard fuses or relays clicking as I was gently braking and gently taking a right turn. I continued the right turn off into a parking spot on the side of the road and stopped the car. I turned the key to the off position, put it into park and restarted the vehicle right away. No problems. All was fine.
The vehicle did not do this again for the entire trip. However, I did perform some tests to see if I could repeat a similar failure with the ignition alone.
1) Turning the ignition off and quickly back on again by hand while rolling at highway speed (~55 mph) will cause the vehicle to kick back into a normal running mode.
2) Turning the ignition off and quickly back on again by hand while rolling at lower speed (~30 mph) will require a restart by turning the key all the way to the "start" position and not just the "on" position.
3) Turning the ignition off with the key (as in 1 and 2) DOES NOT cut out the radio. Note that when the intermittent defect occurs, the radio will cut out and then come back along with the engine and instrument panel.
4) Wiggling and stressing the keys to put strain on the ignition switch doesn't seem to cause anything to happen.
5) The battery is only a few months old and a general inspection of the battery terminals, cabling, and fuses indicates that everything appears to be in tact and clean.
I'm not the most experienced car person, so my terminology is probably a little off and that's all I have for now. I feel like this is a common ground issue and if I could only identify which ground services the instrument panel and radio and spark plugs I could inspect it and clean or replace a connection. My limited research reveals that there are many grounds throughout the engine compartment, though.
View 10 Replies
I have a 2006 Outback XT, which recently started shuddering (like it wants to stall) at idle... At least that's how it started. I noticed it for a few weeks but with no check-engine light, and no error codes cropping up, I kind of ignored it. It then started to stall at idle. Took it to my local guy, who checked all the simple stuff: vacuum hoses, mass air flow sensor, he even removed and cleaned up the throttle body. But the problem persists.
I guess the part that really has me puzzled is the lack of a check-engine light or an error code. With how computer-regulated cars are nowadays, I'm baffled as to how this isn't causing some alarm to go off.
View 9 Replies
Took my 06 Outback (106K miles) in to have the right front inner & outer CV boots/axle assembly replaced (one of the boots had torn open and was slinging grease everywhere, so no surprise there). When I was driving home after picking the car up, I noticed what felt like a wobble or shudder that seemed to come from the center or right side of the car (I couldn't tell which). It would only happen while accelerating, kicking in at about 20mph and then seeming to go away at about 30mph. It didn't happen at all while coasting, braking, or decelerating. The more of a load there was on the engine, the worse the wobble/shudder was, and if I accelerated very very slowly it wouldn't happen at all or would be just barely perceptable. I didn't feel it in the steering wheel; it was more like something felt through the seat and the car itself, if that makes sense.
So I took the car back to the shop the next day, and although the owner of the shop said he drove the car and didn't notice anything, he decided to go ahead and do the job over under warranty just in case they had installed a bad axle or had otherwise "botched" (my word, not his) the job. He also rotated and rebalanced the tires on the off chance that's where the issue was. Within about 15-20 minutes of picking up the car the 2nd time, I started noticing the wobble/shudder again, always under the same conditions as I've already noted--only while accelerating, always kicking in at about 20mph and going away at about 30mph, and always worse the more of a load there was on the engine/the faster the acceleration. The only additional info I've been able to glean is that it doesn't ever seem to happen when I drive the car first thing in the morning, but starts to happen as the car warms up.
At a complete loss, I crawled under the car and starting looking and poking around for something that might be loose or knocking around. I was particularly interested in determining if there was any play in the U-joints or some kind of damage to the drive shaft. I didn't notice anything except for this--at different points on the drive shaft there are what I assume are balancing weights welded to the shaft. Well, I found a bare spot toward the rear end of the shaft that seems as if a weight used to be there (although I can't say with 100% certainty). The drive shaft is painted entirely black, as are the weights, except for this one shiny, bare-metal, square-shaped spot. "AHA" I thought to myself...balancing weight broke off (although how that would happen beats the heck out of me since it's fairly well-shielded from road debris...maybe it was just a cr@ppy weld), now the shaft is out of balance, hence the wobble/shudder. However, the more I thought about it, the more I wondered...if the shaft was out of balance, why would it only wobble while accelerating? I understand why it might only do it at certain speeds, but if a shaft is out of balance, shouldn't it wobble/shudder at those particular speeds regardless of whether I'm accelerating, decelerating, or coasting? And why would it not seem to happen until after the car had been driven for 15 minutes or so and had warmed up? Again, it seems like an out-of-balance drive shaft is going to be apparent regardless of the operating temperature of the car.
So, could I be on the right track? And if so, is the fix as simple as welding a new weight on there? Can this be done with the shaft still on the car? I think Subaru considers the shaft a non-serviceable part, but I don't want to trash and replace an otherwise perfectly good shaft for what seems like a pretty easy fix (albeit one that is probably beyond my own abilities).
View 2 Replies
I thought it was the tired due to the cold weather. But now it is warmer the noise is still there. Bareknuckes previously mentioned wheel bearings as a potential problem. The car is driving (sound-wise) like I have some huge mud-bogger tires on or like crossing a cattle-guard continuously. so loud (in the cabin) that sometime I forget to shift because I hear the humming rather than the engine.
View 2 Replies
2006 Subaru Outback. It has around 121000. I bought it at 113,000 last October since my previous 1998 Subaru made it to 240,000. So far I've taken it in for all new wiring and a tune up. And I was assured by the car salesman that the timing belt had been changed prior to my purchase. Anyway, since August I've had a rattly/whirring sound that I am experiencing over 15 mph. It seems to be coming from the back of my vehicle. It sounded like I had a hole in the muffler because it was reminiscent of when I lost my muffler on the highway with my 1998 subaru a few years ago, but this sound is definitely not as loud. The sound does increase in volume at high speeds on the highway but has so far not been as loud as my previous experience. (and the muffler is still there when i look under the car)
When I took my car in to get the oil changed a couple months ago, I asked the mechanic to check and see if he saw anything while under there. They told me it was my heat shield.
Recently the noise started being a little bit louder on the highway so I thought maybe it was my tires since they were very due to be replaced. I bought new tires within the last few weeks and there has been no change with the whirring sound on the highway. Yesterday, I noticed a light thunking sound that started happening between the speeds 10-40mph. It seems to be in the front of my car and occurring with the rotation of my wheels. There are no sounds when Idle.
View 3 Replies
I have a 2006 2.5 limited turbo outback wagon. Recently the engine light came on not flashing..the cruise control light is flashing. I live in a very remote area over a hour away from a dealer ship..and having problems finding someone with a diagnostic tool..Am I damaging my car by driving it still..I did just prior to the lights coming on filled the tank and after checking the cap I realized I did not tighten it as I should have.
View 6 Replies
I believe that I have a leaking CV joint boot in my 2006 Outback. Occasionally smell something burning. Lifted hood and had some smoke. Saw leak and a friend stuck a finger into a hole in the boot.
View 9 Replies
I have a 2006 Subaru Outback. When I start it, it makes a constant rather loud rumbling noise that seems to be coming from the rear of the car. I can feel a little vibration through the steering wheel, but when I put the car in neutral the noise/vibration goes away.
View 10 Replies
Over the past year we have been noticing that the HVAC blower doesn't turn on from time to time. All settings in the control panel seem normal and the fan speed is turned on. Most of the time everything is working normally, sometimes when the car starts the blower isn't working and then starts after a minute of driving. Sometimes I notice the blower isn't working and I turn up the fan speed and after a few clicks it starts working normally for the remainder of the drive. And then sometimes the blower doesn't ever start and I need to turn off and restart the car a few times. When the blower hasn't been working the a/c compressor has been turning on, something in the blower circuit is failing.
There are five possibilities:
The HVAC controller isn't telling the blower to turn on
The power relay isn't always working
There is a wiring or connection problem
The blower motor itself isn't working
The power mosfet is failing.
What needed to be replaced?
View 2 Replies
I have a 2006 Dodge Caravan that when I drive at highway speeds and it's wet out, my air bad light comes on and about 50% of the time, the radio, fan, windshield wipers, and 12v outlet stop working suggesting the fuse or some other wiring is getting wet. The dealer cannot replicate and will not suggest any fixes. What do I have my local mechanic replace or seal?
I know there's a Chrysler recall on 2005-2006 Caravans, #J38, but my Caravan falls outside the specs by 2 mths (it was for vehicles in service between Jan 2005 and April 2006).
View 11 Replies
My 2000 outback wagon has only 67k miles. About a month ago, the check engine light came on. I took it to an Auto Zone and although unfortunately I didn't write down the code, the person who checked the car seemed to think it was probably just a bad tank of gas. I ran through that tank of gas and filled up with premium gas. Light didn't go off until THAT tank was near empty. Filled up a third time and light remained off until tank was near empty and it came on again. It has not yet gone off. I'm not sure how many more tanks of gas I should run through! The car isn't running poorly so I thought the bad gas was a good explanation.
A side note: about 6 months ago I had to have the head gasket replaced. I argued with Subaru and got some extra work done in exchange for the head gasket payment since my car missed the recall by a few digits but I was obviously stuck with an inferior product. I'm hoping they didn't do an inferior job. Even though it was 6 months ago, it wasn't that many miles ago - you can see my the year/mileage on my car that I don't drive a lot. Does that gas explanation sound reasonable? Anything about a head gasket related?
View 13 Replies
Having problem with corrosion of the tie down on a battery? The terminals are fine. It's just the metal plate that holds the battery in place with bolts. The paint has corroded off. I clean it up and cover it with dielectric grease. I have to do this every 4 to 6 months or so, because the corrosion keeps coming back. I had the same problem with my 2004 Subaru Legacy, and had to replace the battery holder as a result.
View 1 Replies
my car has tge 3.6 motor and has 2500 miles and seems to be loosing coolant...
View 2 Replies
Our 2011 Subaru Outback 3.6R, which we bought brand new back in Feb ’11 and only has 4k miles, seems to be having issues with the cooling fan. The cooling fan will come on when the engine is cold and it will stay on the entire time the engine is running. I’ve read that the cooling fan will run the whole time when either the A/C is on or the vent control is set to defrost, regardless of whether the engine is cold or hot. In my case, the cooling fan comes on when the engine is cold, even with the HVAC off and it will remain running at full speed when the engine is running, again with the HVAC off.
Every time I go to start the car after it has been sitting for an entire day and the engine is cold, when I turn the key to the “On” position, before the engine is even started, the cooling fan comes on. How is this possible when the engine isn’t even running and the engine is cold. Again, the HVAC is off. Once the car is started, the cooling fan will remain on until the car is shut off. The fan is running as such a high speed you can hear it over the noise of the idling engine. Once I turn the car off the fan shuts off.
Since we’ve owned the car there were two other issues First, the transmission pan gasket wasn’t properly installed and it was leaking transmission fluid. That issue was fixed and is good now. The second issue was that oil was leaking from the timing chain cover. It turns out that the timing chain cover gasket was also improperly installed. This too was fixed, and doesn’t seem to be a problem anymore.
View 5 Replies
I purchases a 2012 Subaru Outback i2.5 Premium in January. The car has been stalling out after getting gas; I've put gas in it about 10 times, and it's stalled out or nearly stalled out after 4 or 5 of those times. The first time it happened I had to have the car towed back to the dealer. At the time, they thought it was bad gas, but the repetition of the problem has them stumped. There are no warning lights or error codes. I have had the car back to the dealer on four occasions, and unfortunately they can't replicate, find, or correct the problem. Now Subaru is involved. The car also runs rough and shifts rough, compared to the identical 2012 Outback I was given as a loaner the last time I had it in.
View 6 Replies
Where the heck is the gas cap release. Just bought it to get back home as the jeep needs broken motor mount fixed and had to leave it in town. The subaru is pretty beat up so the gas cap release could be hiding (as in handle gone) ?
View 5 Replies
I own a 2002 Outback. It is overheating. We have replaced hoses, thermostat, water pump, the temp sensor, had the radiator tested. Nothing has changed our problem. My husband is at a loss and the mechanic who has is now has no clue as to what else it could be. The mechanic is referring to it as a ghost problem.
View 19 Replies
I have a 2001 Subaru Outback with the 5 speed manual transmission. About 6 months ago the clutch went out and we had it replaced. We did not go to a professional shop and instead used a friend of my father-in-law who used to be a mechanic. Last weekend I drove the car on the beach to go fishing and got the car stuck in the sand.
After 2 attempts to get unstuck the clutch started smoking and blew out. I only attempted to get unstuck 2 times and was not "rallying" the engine hard. I realized I was good and stuck and stopped because I didn't want to spin the tires and dig myself so deep I couldn't get towed out.
My question is this; what are the chances that a brand new clutch would blow after 6 months? The car is used mainly to drive on paved roads to and from work and the grocery store. Both my wife and I have driven manual transmission cars for years and we don't ride the clutch. It goes through the usual wear and tear of everyday driving and yet, one incident that requires a little beef from the clutch and it blows?
View 5 Replies
I have a 1998 Subaru Legacy Outback (automatic) that has 176,779miles on it. I live in San Francisco and only drive the car occasionally every 2-3 weekends out of the city. Recently within the past month I have noticed that after turning on my car and once it is in drive for the first 10-15 minutes it has a hard time getting past 20 mph. When I put the foot on the accelerator to go past 20mph the rpm goes way up to 4, 5 or 6. Once it gets past this then car is smooth and I have no problems. This problem seems to go away within 10-15 minutes of driving or if I turn my car off and then on again it seems to go away. I called my mechanic and they said it could be that the transmission fluid is low. I checked the level and it is perfectly normal.
View 2 Replies
