Subaru - Outback :: 2006 - CEL On With Cruise Control Light Flashing


Jan 30, 2011

I have a 2006 2.5 limited turbo outback wagon. Recently the engine light came on not flashing..the cruise control light is flashing. I live in a very remote area over a hour away from a dealer ship..and having problems finding someone with a diagnostic tool..Am I damaging my car by driving it still..I did just prior to the lights coming on filled the tank and after checking the cap I realized I did not tighten it as I should have.

View 6 Replies

Advertisement

Subaru - Outback :: 2004 - Cruise Control Flashing - Replaced Both Banks - Catalytic Converter?

engine light and flashing cruise control switch--computer says replace bank one---so I replace with factory catalytic converter----six months later light comes back on with flashing cruise control switch and computer asking me to replace bank one---So I use computer to shut light off----four weeks later light comes back on----called dealer they said "we usually replace both banks"---I found it most painful paying for dealer supplied catalytic converter even when I was under the impression that it would keep light off.---This is my wife's car and she is not really buying the piece of black electrical tape I placed on dash over check engine light.---Am I dealing with a bad oxygen sensor ?

View 5 Replies

Subaru - Forester :: 2006 - Check Engine Light Came On And Cruise Control Started Flashing

I just bought a 2006 Subaru forester with 130K miles. Recently, the check engine light came and at the same time the cruise control started flashing. I brought it to the mechanic who said I had a bad catalytic converter. The car seems to be running just fine and now a day later the engine light is off.

View 3 Replies

Subaru - Outback :: 2010 - Brake Warning / Traction Control / Cruise Control / Check Engine Light Came On?

My 2010 Subaru Outback recently surprised the hell out of me by simultaneously turning on the brake warning light, the traction control light, the check engine light and (just for a bonus!) disabled my cruise control while flashing the cruise control light. I pulled over, quickly surmising that all of those systems could not have failed at 70 MPH without instantaneous death to either me or the vehicle. Both apparently still being alive, I tried turning the car on an off to reset the lights. No go. Subaru was not going to miss this chance to get me to the dealership! (who I had avoided to this point!) As I was far away from home and the car being very healthy, it seemed, I decided to drive on. I proceeded to put a couple of hundred more miles on the car before I got back to town.

My car had 39,000 miles on it, 3,000 miles beyond the warranty end. I learned that I have an error code of P0171, "Fuel Trim Malfunction (Air/Fuel too lean)". So I guess I'm wondering about a few things...why would this sensor set off every light on my dashboard and disable my cruise control? Seems a bit overblown for running a bit lean. My gut tells me Subaru has a sensor/software problem they are not owning up to. I'm a big fan of conspiracy theories and this really smells like one...

Second, jeez, I'm only 3K miles over warranty, don't you think they'd cut me some slack. I mean I love my Subaru, or did anyway, until this happened. Now it's just another POS car that breaks for no apparent reason...

View 10 Replies

Subaru - Outback :: 2007 - Gas Pedal Intermittently Become Unresponsive / CEL And Cruise Control Light Blinking

I have a 2007 subaru outback ll bean addition with 67,000 miles. For the past year and a half my gas pedal has intermittently become unresponsive. The engine is running just fine but the check engine light and cruise control light start blinking and boom-no gas. After turning off the engine, the car won't start until the gas pedal has magically started working again. The dash lights continue to blink for several starts but then stop.

Prior to this problem, I have noticed that sometimes the console lights for the radio and AC blink and sometimes go dark at which point the controls are ineffective. As if this wasn't enough, just yesterday when trying to start the car, the engine was having trouble turning over with a rapid clicking noise. It eventually started but now the seat belt buckle alarm is out of whack and the speedometer displays "ER U1."

View 10 Replies

Subaru - Outback :: 2011 - CEL / Vehicle Dynamics Control And Flashing Brake Light On

I'm on a road trip and was taking off this morning when my CEL, vehicle dynamics control light came on steadily, with a flashing brake light. It's Sunday and no repair shops are open and I need to drive from CO to S. Cal today. Is it safe to travel? From what I've seen, it could be a problem with the gas cap or ABS is disabled. Haven't had cruise control light come on (yet), but haven't tried driving anywhere.

View 4 Replies

Subaru :: Engine And Cruise Control Light Flashing On And Off

I have a 2005 Subaru Outback with 179,000 miles on it. My engine and cruise control lights flash on and off....have been doing this for 6 months now....intermittently. My mechanic said the he cleared the computer and to wait and see if it happens again. He said that it might be the catalytic converter. The car runs fine whether or not the lights are flashing.

View 3 Replies

Subaru - Forester :: 2007 - CEL And Cruise Control Light Flashing?

On my 2007 Subaru Forester (100k miles) the CEL light is on and my cruise control light is blinking (cruise control does not work in this condition). Computer scan indicated front O2 sensor failed and my mechanic replaced it. No joy. Computer scan reported 0 data from EGR valve--replaced it. No joy.

View 2 Replies

Subaru - Legacy :: 2004 - Engine Light Comes On Along With Flashing Cruise Control

My mechanic can't find the problem. Engine light comes on. Along with the flashing cruise control. His diagnostic doesn't show him the exact problem as the voltage changes. He has checked everything related, changed out the bank 2 sensor 1 oxygen sensor, but can't find the problem. I don't know the diagnostic code. But he says that it doesn't give him an exact code. Can only the dealer do this? Car runs fine.

View 10 Replies

Subaru - Legacy :: Check Engine Light Turning On And Cruise Control Light Flashing

Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.

View 6 Replies

Subaru - Outback :: 2012 - Cruise Started Flashing And Warning Lights Came On

Two weeks ago I bought a new 2012 Outback. While driving in the manual auto mode, the cruise started flashing, the check engine came on, the traction control light came on and the brake light was on. The dealer said it was because I did not tighten the gas cap, letting air in. They reset it but a few days later it came back on again and this time they said it was miss fire code. Since they couldn't figure out the issue, they did the right thing and traded it in for another, identical 2012 Outback. Now, 8 days later, all the same lights have come on.

View 7 Replies

Subaru - Outback :: 2000 - Flashing Check Engine Light

I have a 2000 Subaru Outback. The check engine light has been coming off and on for the past couple weeks, but today the light started flashing. The car is running a little funny - not accelerating well and shaking when I start it. What's wrong with it?

View 4 Replies

Subaru - Outback :: 2007 - Tire Pressure Indicator Light Flashing

My Tire pressure indicator light starts FLASHING after driving for 15-30 minutes. It does not stay on but continues to flash every 3 seconds. I stop to check tire pressure and my tires are fine. After a couple weeks of this, I took it to the Subaru Service who checked the tire pressure indicators and it said all 4 of them were bad. They reset them versus replacing them and 20 minutes after I left the subaru service center, the flashing started again.

Subaru says that it is unusual for all 4 to be back at the same exact time and recalibrating them should have fixed it. Now they would like to replace each of them for about $150 parts&labor EACH. That seems crazy. Is there something else wrong? Something else they can fix? Is this a legitimate repair? My subaru is the Limited LL Bean version, 6 cylinder, has 60K miles on it and is in top condition. Had new tires put on 10,000 miles ago.

View 2 Replies

Subaru - B9-tribeca :: Check Engine And ABS Light Came On Along With Cruise Light Flashing

I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.

After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.

On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:

Camshaft position actuator A - Bank 1 timing over advan.

Camshaft position actuator A - Bank 2 timing over advan

Cam/crankshaft pos. correlation sensor A - Bank 2

Cam/crankshaft pos. Correlation sensor A - Bank 1

Camshaft position actuator A bank 1 timing over - advan

Camshaft position adctuator A bank 2 timing over -advan

Cam/crankshaft pos correlation sensor A - bank 1

I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.

Is there something more major going on here with the computer?

View 5 Replies

Subaru - Forester :: 2007 - Cruise Light Is Flashing And Check Engine Light Is Solid

I have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.

View 2 Replies

Subaru - Legacy :: 2005 - CEL On And Cruise Control Light Is Blinking

My 2005 Subaru Legacy 2.5i - the engine light is on and the cruise control light is blinking. This happened once before and it went away after I recapped the fuel cap. However, this time it did not work. The car is running ok.

View 4 Replies

Subaru - Impreza :: 2007 - CEL Suddenly Comes On And Cruise Control Light Starts Blinking

So I'm driving along with everything fine till I pull into a neighbors driveway to drop off some stuff. As I pull in, the check engine light suddenly comes on and the cruise control light starts blinking. As I have a scangauge II always connected, I put the car in park and check the code. It comes up as P0000. I get on my Droid III and google it - all I see is "null code" so I clear the codes and everything is fine. I figure "that's odd, but whatever". I drive home (about 1000 feet) and park and shut the car off and go inside to mull this over.

I go back out to check out the scangauge again and it requires starting the car to read out the codes. The car won't start. The battery is fine, and in fact it does the "rurrr rurrr rurr" strongly for 10 times before I figure it's not starting. I wait about 30 seconds and try again - same thing. I wait about an hour or two and try again and it starts this time right away, but then stalls right away. Start again and manually give it some gas and it keeps idling weakly. I'm able to back out and drive a short distance and come back without a stall. I let it sit for the weekend (no shops open anyway) and start it monday morning with my AAA card out... and it starts fine and runs fine all day. I basically forget about it.

About a week and a half later, I'm driving along a country highway at 55 Mph, and the same thing happens. Check engine light, cruise control light blinking and the cruise actually cuts out so I'm losing speed suddenly. I run the scangauge again and same code. The car keeps running fine though, I'm able to drive it back (w/out cruise control) the 5 miles home. Nothing out of the ordinary.

I go inside and google this some more, and there's some posts about the Scangauge causing this - but I've been using it for about 4 years w/out this happening. That said, about 2 months ago, there was a recall, and they flashed the ECU with some update so maybe that changed something, but still - worked for months before this happened. I had to get to work etc so I just cleared the code again, and so far 3 days without a recurrence. Currently I'm thinking about waiting to see if it happens again and going to Autozone and have them read the code to see if it really is the Scangauge not reading the code right or whatever...

View 3 Replies

Subaru - Legacy :: 2011 - All Lights Flashing On Dash / Cruise Would Not Engage

Last week, the brake, traction control, cruise, and check engine lights all came on my dash. All but check engine were flashing. The car seemed to be driving fine but cruise would not engage. I drove it to a local mechanic who checked the battery and alternator and reset the computer. He said there was nothing wrong with the car. The next day the lights started flashing again so I made an appt to take it to another garage. This place said my gas cap needed to be replaced (hence the check engine light) and that my vehicle dynamic module was busted. My dilemma is that since picking the car up 4 days ago, and driving roughly 200 miles since, the lights haven't come back on. My current plan is to wait a bit and see if they do but I'm wondering if there's a chance that the VDM is ok.

View 19 Replies

Elantra HD (2006-10) :: Cruise Control Does Not Work After Changed Brake Light Switch

I just discovered my cruise won't "SET" (light goes out after 1/2 second) anymore after having the brake light switch done yesterday.

View 2 Replies

Repair :: Engine And Cruise Control Lights Keep Flashing Intermittently?

My engine and cruise control lights keep flashing....This happens intermittently (been going on like this for several months). I took it to my mechanic and he cleared the computer...was fine for awhile...but happening again. Mechanic said that if it happened again, it might be the catalytic converter. I hope not b/c this is a very expensive part to replace!!! Is my mechanic correct or could it be something else?

View 3 Replies

Subaru - Forester :: 2005 - CEL Came On - Cruise Control Started Blinking?

I bought a 2005 subaru forester xt a cohple months ago and then the CEL went on and the cruise control started blinking. The car also shook horribly. Long story short, and $2,300 later, i got the "head gasket set, water pump, timing kit, oil&filter change, " etc... Fixed. Question is, I am driving to Colorado from Maine in about two weeks. How long do subarus last after such repairs? Think ill get a few years out of it? Or should I sell it and buy a more reliable car before the trip out there.

View 11 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved