Toyota - Camry :: Rough Idle - Parkway Stall
Jul 12, 2013
My 2001 toyota camry is great but has an intermittent, annoying problem no one can diagnose or correct. If I drive for a while at top highway speed (say 65mph) and then have to come to a stop (to pay toll or stop light) I get a very rough idle and then the car stalls. Have had new plugs, wires, coil, radiator already done to solve problem. Check engine light never comes on. Can also drive lengthy trip and it doesn't happen.
View 18 Replies
Advertisement
I fill my gas tank to 100% but I don't pump it again and overfill it like most people do after the pump stops. I then proceed to start the car. Initially it revs up and starts fine but when it revs back down to idle it does a rough idling (and sometimes it stalls). To get around the stall, I would restart and rev the engine to 3000 rpm for about 2 mins and it would be fine enough that I can drive away without it stalling but after a mile the rough idling stops and everything is back to normal. I replaced the PCV valve and it worked for about a year but it all came back again. I am stumped and every mechanic gives me a different reason and none of the reasons are even definite. It's one of those "lets try this and see what happens". One more thing, the car runs fine. It only happens when I pump more than 75% of the tank.
View 5 Replies
I have a 2008 Toyota Camry SE with the 2.4 engine and auto trans. If I'm stopped and in drive the engine feels as if it's going to stall, the entire car "shutters". The tach reads between 700 & 800 but if I place the gear selector into either neutral or park it becomes "glass" smooth, I even have to look at the tach to see if the engine is still running! In neutral or park the tach still reads 700-800 rpm and the A/C is always switched off.
I've had it to 2 different Toyota dealers and yesterday to my regular mechanic. 1st dealer said to disconnect the battery and bring everything back to default positions...no difference, battery was off for 35 minutes. 2nd dealer said to have the throttle body cleaned, which I did...no difference. A bit of background with the vehicle, I've had it since new, I drive 170 hiway miles per day, I use Shell branded fuel, oilchanges always at 5,000 miles, dealer serviced since new.
So yesterday my mechanic checked everything, engine mounts (OK), any error codes (none) cylinder compression (all within spec) spark plugs (OK except for 1 so I asked him to change them all), he installed 4 NGK iridium plugs and guess what...it still shutters & vibrates!!
View 3 Replies
2002 Toyota Camry
2.4 V4
My car has developed a rough idle when stopped and when accelerating. When I got the CEL, I had the codes read at Advance Auto.
The codes are P0301, P0302, P0303, P1349.
View 1 Replies
My car started a rough idle last night.... Pull to stop light, in gear, a/c on #1 and car shudders and acts like it's going to stall..... Went away as I drove a round a bit.....back this a.m. (after the warm up program ran) drove it a bit and was sporadic.....and even went away...then came back.....
Its worse when car is at stop and in 'D'.....little better with a/c off and/or in neutral......it finally threw the CEL today....... I had the fuel pump recall done about a month or two ago, car has 36k+ on it...... Anything I should have the service dept look for aside from what the fault codes might read?
[URL] .....
View 7 Replies
So this morning when I went to start my car for work, it wouldn't idle and was misfiring badly, also has a very loud noise coming from the valve cover. The car has under 40k miles on it and is CPO, so it'll be towing it to the dealership today to get check out. The car ran fine on friday when i parked it.
Here is a vagcom scan I did this morning also.
Monday,25,August,2014,06:03:51:26742
VCDS -- Windows Based VAG/VAS Emulator
VCDS Version: 12.12.2.0 (x64)
Data version: 20140212
VIN: WVWHD7AJ2BW201261 License Plate:
Chassis Type: AJ (7N0)
Scan: 01 02 03 08 09 15 16 17 19 25 2E 37 42 44 46 52 55 56 62 72 77
VIN: WVWHD7AJ2BW201261
01-Engine -- Status: Malfunction 0010
[Code] .....
View 3 Replies
Last week I had the plugs, coils, valve cover gasket and fuel filter done my 2004 Ford Escape when the engine started misfiring and today it started to idle rough at a stoplight and it seemed like it was going to stall but didn't. I had it sit for about an hour and a half and the it did want to turn over like the battery did have enough cold crank to it but it did after a couple of times. It has come and gone for the last couple of hours. No warning lights are one either. It seems pretty close to what it was doing when it was misfiring. What it may be?
View 10 Replies
When I start my S60, it runs extremely rough and will eventually stall. I do this over and over . . try and put it in gear and it will go a bit, run very rough, and will stall out. After a few minutes, something kicks in and it runs perfectly. If I don't try to drive, and sit with it idling, it runs very rough and I have a difficult time getting the rpms up. Then, the engine will suddenly race for a bit and everything is fine. It is very periodic in nature, doesn't matter if the engine is cold or not. It can sit over night and be fine, or do it, I can run around all day without problems and then suddenly it decides not to start up and run. The temperature outside doesn't seem to be a factor.
View 2 Replies
1993 Nissan Maxima. Great little car except when engine gets warmed up it begins to run rough and dies. At idle, when accelerating, while maintaining speed. Since its a manual it is a simple matter of dropping into neutral and it fires right up again... no problem. Then stall repeats. Went through routine steps checking plugs, filters, wires, sensors etc.. The O2 sensor (only one) is gone - as is the converter. At some point someone replaced it with a straight pipe.
After not finding a obvious answer, I began to ask around (auto-part stores, neighbors, some patrons at the saloon). Conclusion... OBD failure causing a "kill" routine which shuts off the engine. When I restart, it resets. Once it fails to enter a static state (engine is warm) it kills again. I replaced the computer with a used one "known" to operate (so the e-bay seller said) Installed it and bingo, car ran like a top for 15 full minutes - best ever. Then after 15 minutes or so, suddenly began to run rough and stalled twice before I got back home. I runs now just as before (but oh those glorious 15 minutes).
View 1 Replies
I have a 2013 with the 3.7 in it with 24,000 miles on it. I bought the truck used with 8,000 on it was a pre-Owned certified and it already had a k&n air intake which I know it's not needed and I would much rather have the factory intake instead.. 7 months ago I took it to the dealer because I noticed at stop lights it idled rough sometimes almost feeling like it was going to stall out so I took it in and they said that the motor was getting to much air and causing it to run like it was and they said the cooler weather was making it worse and said it should get better when it warms up and they said it wouldn't hurt anything... Well I live in Florida and it's been in the 90s and it still idles like crap you can feel the vibration through the truck...
And it's so aggravating and annoying and I wish I had a stock intake that I could install on the truck to see if it fixes the problem but I don't and I've researched the problem and have seen people with the same issues without the k&n air intake and I've also been told that the stock air intake gives the motor just as much air as the k&n so with that being said did the dealer take the easy way out and blame the intake or should they be responsible for installing the factory intake back on since they made it a certified pre-owned with the k&n on the truck? It's been frustrating because I don't know a whole lot about gas motors.. And I'd like to get the problem fixed while I still have warranty ..
View 8 Replies
Let me describe this perplexing issue. I have a speratic rough idle problem. When it happens it's almost like the truck wants to stall. Once going the truck is fine. There has never been any acceleration issues, but for a short time the truck would kind of lunge off idle. It hasn't done that for quite some time. I've replaced the fuel filter. There are no vacuum leaks that I know of. I've tried higher octane fuel. I've tried injector cleaner for a month. What should the fuel pressure be and what is the test port located? Is the fuel pump in the tank? If so, whats that big log looking thing behind the gas tank that the fuel lines run to? Also, there are no MIL codes...
View 14 Replies
This morning when I started my car the RPMs were all over the place. The engine would rev to just below 2k and then drop, as it it were gonna die and right before it did, it would rev back up. Then, when I tried to move it, it would not accelerate and would hardly move and while coasting it dies if the clutch is depressed. The car does not die when idling (albeit a very rough idle) but it does when it is moving.
It flashed a check engine for a few seconds at one point but went away and has not come back on. I am running APR Stg 1 and a Carbonio intake. I switched from 93 octane mode to stock and nothing changed.
View 3 Replies
My truck is a 1995 Explorer 4.0 150,000 miles, 5 speed.
Problem - Rough idle : when cold it's worse and will stall and choke a little. When warmed up it just has a rough idle but will not stall and stays at a pretty constant RPM. It's very tolerable when warmed up but still not right. It drives fine once off idle. No black smoke that I can see. Power may be just a little off but I would not bet on it. MPG seems about normal but haven't been on a long enough trip since problem started to tell for sure. Also longer than normal cranking on occasion.
Diagnostics so far : Fuel pressure is at 32 PSI, vacuum off regulator it's at 40 PSI. Not sure about key on only as I don't trust the autozone loaner gauges. You have to fiddle with it each time before it will read. Leak down after 30 minutes was about 4 PSI
No Check engine light ever. KOEO test shows no hard or on demand codes, I get the 111 pass. From CM I get 336 and 45.
336 is EGR related and my looks pretty rusty. I put a vacuum pump on it while running and the EGR held vacuum but had no effect at all on idle, I was expecting it to get worse as I opened the EGR so it may be stuck.
Searched high and low for vacuum leaks by ear, visual and with starting fluid all turned up nothing.
Actions so far : Replaced plugs, wires, IAC, and fuel filter. Cleaned MAF sensor and throttle body plus ran lucas fuel injector cleaner through it.
Next steps : I've got the EGR but it's so rusty I am sure I'll break the tube it bolts to plus I don't know it that alone will cause the rough idle. Will the DPFE sensor and/or EVR create a rough idle yet not turn on the CEL?
Thought about changing the fuel pump and/or regulator but the numbers are not terrible. Agree?
Thought about changing the intake gaskets but don't see any leaks.
View 8 Replies
So about 2k miles ago I went to start my tiguan (cold start) and it starts to idle very rough, barely keeps itself from stalling so I take it to the dealer the next day and they tell me the car needs carbon cleaning and a rear main seal and wanted about $2500 to do all this. I declined the service since it was a lot of money to just drop then and there. I am wondering/worried there are other issues along with the rear seal leaking or if its just something else causing the issue. I looked under the car and most of the bottom of the motor is soaked in oil. I have not done the auto trans service on the car and was wondering if that could have had anything to do with the leak. The other thing about it is once the car gets up to temp it runs totally fine. AND once in a while it will start up fine, no rough idle. That probably happens about 20% of the time (I do at least 4 starts throughout the day). The car current has 92k miles on it. What it could be/what I should do?
View 10 Replies
Noticed this to be a problem with our older 2011 Accent, now with the 2012 Accent.
The car has a rough idle usually in mornings, it seems like it is going to stall at stops, it also has a tough time accelerating.
The computer scan does not show there is anything wrong until the problem becomes worse.
This is what I have discovered through the 2011 Accent. Car will stall at stops. Very inconvenient in rush hour traffic. Until they replace the Crankshaft Point Censor, the problem would not go away.
I would insist on looking at this rather than replacing sparkplugs or having any other service performed if one is experiencing these same symptoms. The good thing is it is under warranty.
View 1 Replies
I have a 2013 Golf TDI with 2070 miles on it. For around 2-3 weeks, I've noticed that it intermittently will idle rough, shakes, etc, as if it is about to stall out, but stays running and drives normal. I figured it was a typical Diesel thing and wasn't too worried about it. However, today, this happened, and I got an engine light. Yikes! I made an appointment for it but need to wait till after the 4th for it to be looked at. What's up here? Is it a regen cycle? Timing issues? Am I doomed with my Golf TDI?
View 8 Replies
I have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 Replies
I have a 2002 4.6L FX4. When I run the A/C for an extended period (say 15-20+ minutes), it will start to cough and sputter and eventually just die. It will restart but run rough and cough, sputter, die.
If I turn off A/C and let it set a while, it runs fine. No check engine light. Possible EGR problem????
View 3 Replies
Had a tune-up and a mechanic also looked at the accelerator pedalfor some reason, but no report regarding the fuel injection or regulatory components which I suppose should have signaled an issue when the computer diagnostic was run if I am to understand the mechanic's position.
View 2 Replies
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 Replies
I have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
View 3 Replies
