Accent LC (2000-05) :: Intermittent Misfire / Running Rough
Jan 17, 2014
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
View 12 Replies
Advertisement
My 740 (1990, B230E, non-turbo) has been running rough at low rpm. Once above 1800 rpm or so it's fine. I've changed the Distributor cap and rotor arm (they were both shot), but the problem persists. I'm thinking injector relay or ignition stage amplifier next, but I don't want to just through parts at it.
The plugs were changed 3 months/1,500 miles ago. The misfire is intermittent.
View 1 Replies
I have a 2000 excursion 4x4 v10 with 90k. The past few months I've noticed a tug or miss fire at low RPM (2000 AN UNDER) the past week its gotten worse, some occasional rough idol and the missing is getting worse. Whats wrong?? I don't want to take it to ford yet! No Check Engine Light yet...
View 14 Replies
This is what my car is doing after it warms up. It will do it then stop, then do it again and so on. I am pretty sure when the motor is under load it runs a little rough but is hard to tell. The car has 178,000 miles on it. timing belt was done at 113,000. I just replace the plugs and wires changed the oil and the air filter 1,000 miles ago. and it will still do it. I am at a loss as to why it keeps doing this. I have tried injector cleaner, sea foam and engine restore. What would cause this? The check engine light is not on. i replaced the crankshaft positioning sensor about 40,000 miles ago.
Its a 2003 hatch with the 1.6 5 speed .....
View 8 Replies
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
View 26 Replies
Okay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
View 8 Replies
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 Replies
So I just had both cats replaced and now the car is running very rough and trowing out mis-fire codes. What could cause this? Going to disconnect the battery to reset the computer to see if that might work.
View 8 Replies
A few weeks ago my car was running perfectly fine, i filled it up with fuel and then it started running a bit rough. Would drive ok but could feel it surging and if i backed off on the accelerator it would try stall.Also the fumes in the car were a lot stronger than usual. Got home and it stalled, started it up and was idling rough and blowing black smoke :/ no engine light has come on though. I did the typical thing and googled possibilities, the mojority said that it was the purge control valve so i replaced that with a new elantra one (part numbers were the same) and its still running rough We are now thinking it could be the oxygen sensor? Have checked vacuum lines and stuff for air leaks and cant find any. Unplugged the oxygen sensor while car was running and it made no difference at all.. If the oxygen sensor was working properly it would of affected how the car was running, right?
View 1 Replies
My 2000 Accent 1.3 has developed a problem recently: starts fine and revs freely and smoothly when parked. When I pull away it will get very rough like it's firing on only 2 cylinders or so, at certain points during the rev range rather than continuously. Very juddery.
After a minute or so, before the engine temp is even up to normal operating temp (according to the dial) it runs perfectly. When I start it up later the same day it's fine. It only happens the first time in a day that I use it. The more days I go without driving it the worse it is.
In the last couple of years I've changed spark plugs (always in good condition when I replace them), HT leads, coil pack, a lamda sensor (the first after the exhaust downpipe) and a fuel pump and filter.
View 2 Replies
I have had some slight rough running with a cold engine and stumble <2000rpm. Finally it tripped a CEL which was read as a misfire code.
The mechanic swapped the coil and plug(recent) and no change. He did a compression test and air blew out the exhaust. So.......the car needs a valve job which entails motor removal and fixing the head and reinstall. He rough estimates this at $2000 and rate is $65/hr.
He mentioned looking at pistons and may be a bit more if rough.
This car well maintained (170,000 miles 2005 Legacy turbo wagon with manual)...
View 19 Replies
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
View 4 Replies
My g/f's 2004 Ford Escape (3.0L V6 AWD 112,000mi) is acting up. After a full day of sitting, with the second half of it raining steadily, she was driving her Escape and it was acting funny (miss-firing, she said). The engine light came on and soon began blinking. She got to my house shortly after it started this. We left it and I drove for the day. Later that night, I drove it and it seemed fine. The engine light was on, but not flashing anymore.
The next day I took it my friend that was a Saturn mechanic and now working at a KIA dealership (same owner as the former Saturn and current Buick/GMC and Chevy Dealer). It ran fine for me. So he tries to scan it, his Mac Tools scanner won't read it. The KIA scanner wouldn't read it. I drove it the Ford dealer up the road. They said they couldn't get to it until after lunch, I just want the codes read. They re-iterated, and I told them to pound salt and went to an independent shop where I know a guy. They read it right away for me. "Mis-fire on start-up" & "Cylinder 4 Mis-fire." were the two codes stored. He cleared them.
She got the tune up basics (plugs, wires, air filter, etc) and did the complete tune-up herself yesterday. (I was impressed). She put 94 in the tank and some fuel system cleaner in it as well. She said there's been no change and today I finally saw what it was doing. Sometimes during idling at a stop light, the RPMs will drop to almost zero, the lights dim but so far it has not stalled. It'll do this for several seconds, then correct itself and idle normally.
Currently, the engine light has not come back on. She's thinking coil pack (each cylinder has a coil on these engines) on #4. She wants to switch it out with #1 and see if the problem follows. I think that might uncover the cause, or it could be the battery. It's the original, never been replaced and has a lot of miles on it, but it survived this past winter, without trouble. In my experience, most batteries crap out due to age in the fall when the cold snaps start.
View 11 Replies
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
View 3 Replies
I have Hyndai accent Sep-2009 executive model. I have fitted normal CNG kit in my car. I ran it very smoothly for 6 months. Now my car is missing when I am running on petrol but running fine with CNG. If I am removing the battery cable and leave it 4-5 minutes its running fine for 2-10 days, after 7-10 days I am getting the same issue and doing the same procedure for solution.
View 1 Replies
This morning my son started the 2008 Accent and it ran really bad, he shut if off started it again and still ran really bad and check engine light started to flash. Shut it off and ran for the bus to school.
Went and picked up a OBD scanner and found a cylinder 1 misfire. Tried to start it and had a really hard time and when it did start ran like crap and smelled gas. Checked the codes again and now got Multiple cylinder misfires, cylinder 4 misfire and cylinder 1 misfire.
Pulled the engine cover to pull the coils and plugs and I find a ton of mouse crap. No signs of any chewed wires or anything that I could see. Drove it to the local Hyundai dealer tonight because I am worried that it may not be the coil packs. Drove OK to the dealer. My brother is the service manager at the local Mazda dealer and he sees a lot of mouse damage. Said I should put a couple of old socks with moth balls in the engine compartment to deter the mice.
View 4 Replies
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
View 9 Replies
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 Replies
I have a 1990 3.1L, multiport fuel injection (NOT sequential FI), which runs very well most of the time. However, when I cold start it runs rough (misfire) for about 1 minute (no throttle) or until acclerated. The is no misfire when running normal, but it might be running a little rough when stopped at a traffic light (in Drive, foot on brake).
I put new plugs and wires on, but it did not affect this problem.
I am not using coolant, or oil, the plugs that were removed were somewhat worn, enough that I expected to notice a difference after they were changed.
I have not yet (1) cleaned the MAF, (2) checked carefully for vacuum leaks, (3) checked for leaking injectors.
Since this is a 1990, OBDI, I can't say which cylinder is misfiring or how the fuel trims look etc.
View 10 Replies
