Accent LC (2000-05) :: Difficult Start / Rough Idle And Misfire
Jan 26, 2015
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
View 26 Replies
Advertisement
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 Replies
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
View 26 Replies
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
View 12 Replies
After scouring through hundreds of threads on this forum (which is Awesome, BTW), it seems as if this misfire / rough idle thing is fairly common (which is scary!!). CEL is on steady. Had the codes pulled; P0301, P0302, P0303. At the recommendation of the mechanic, I had the plugs replaced...no improvement. He then replaced the ignition coils...no improvement. Just finished replacing the MAP sensor. This actually had a VERY temporary positive effect. However, after about 5 miles of driving, the misfiring returned. Took the car to the Hyundai dealership, and they acted as if they didn't want to fool with it. They referred me to a couple of local repair shops...????
View 8 Replies
2004 Hyundai Accent has is misfiring, after warming up, only in idle. This only happens after about 30 seconds in idle. Could it not be getting enough gas? This being said I was getting misfire on 3 as well but that would happen all the time and cause the entire car to shake. This problem is now fixed and only #4 is causing me problems.
View 2 Replies
I'm having continued issues with my mom's POS 2005 Hyundai Accent. It usually runs great cold, but once it's warmed up, it will stall out while driving. This almost always happens when accelerating from a stop. After it stalls, you have to let it set for 30 seconds to a minutes before it will start again. It will also sometimes idle roughly.
I've changed out the TPS and the MAP sensor, the battery, the CPS, the fuel pump, and the spark plugs. I did find that the radiator bypass hose was leaking on to the wiring for the O2 sensor. I fixed that, and the wires appear to be fine. I've sprayed throttle cleaner around the intake and can't find a leak. I scanned the ODB codes and I'm getting a Random misfire, misfire on cylinders 1, 2, 3, and 4, the Throttle Position Sensor and the MAP sensor, both of which have been replaced.
Tonight during my troubleshooting I was trying the wiggle test on the various connectors and got zapped when I was wiggling the coil pack connectors. Is that normal? I'm starting to suspect a wiring or electrical issue, but I'm not sure how to troubleshoot that.
View 28 Replies
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 Replies
Yesterday my car had a rough start (lasted all of 5 seconds) and it threw the check engine light on. Now other symptoms. It was a rough start, almost like a misfire then it idle fined, and drove my 60 mi commute home without issue. I had fine acceleration, gas mileage idle etc.
I got home and turned it off for 10 min and it then started normally and ran fine again. I'm thinking it was just a random miss that threw on the light, but I'll take it to Advance to get the code later today.
I replaced the plugs about a year ago with cheap-o plugs so it may be time for a replacement again. I thought maybe an o2 sensor but there wasn't a drop in mpg, at least anything noticeable.
And its been a few days since I've gotten gas so I'm doubting just a gas cap issue... The CEL did NOT flash, only solid the whole time.
View 8 Replies
I have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
View 14 Replies
This is what my car is doing after it warms up. It will do it then stop, then do it again and so on. I am pretty sure when the motor is under load it runs a little rough but is hard to tell. The car has 178,000 miles on it. timing belt was done at 113,000. I just replace the plugs and wires changed the oil and the air filter 1,000 miles ago. and it will still do it. I am at a loss as to why it keeps doing this. I have tried injector cleaner, sea foam and engine restore. What would cause this? The check engine light is not on. i replaced the crankshaft positioning sensor about 40,000 miles ago.
Its a 2003 hatch with the 1.6 5 speed .....
View 8 Replies
I'm an Accent 2000 gs owner and since a few days i had this problem. It has a bad idle and looks like it will stall... need to give some gas to stay alive.
Bad acceleration too, it misses some gas. (puffing, rumbling, shaking a bit). After accel, it's ok until the next red light.
Now I can't even drive cause it's worse. (too difficult to accelerate). Is it a sensor?
View 8 Replies
I have a Hyundai-Accent 1.5 GL, Auto, year 2000 car. I bought this 4 months ago and ever since it has been giving the check engine signal. However, running conditions of the car has been normal and therefore, I didn't worry about the check engine signal. Now, the engine is rough idling for few seconds when I start the car in the morning, and then it comes back to normal.
View 12 Replies
I have a 00 Accent with 132k miles, I replaced the motor a year ago with a correct 2000 Hyundai 1.5 with 50k miles. I replaced everything that I could at the time, timing belt , starter, water pump, and clutch. It has been running fantastic getting 40 miles per gallon with zero problems , However in the last week I have noticed a rough idle that seems to miss with a vibration that it didn't have before. I have a noticeable loss of power and torque. My miles per gallon has also dropped to about 25 mpg. My check engine light is not on. I will check the plugs and change the air filter today but I would like to know what else could be causing the problem as I am not really sure what to check.
View 9 Replies
I'm having an issue with my 08 Accent GS. It is very difficult to start, but only after fueling. Any other time, the car starts without any problems. I have tried to simulate the issue at home by taking off the gas cap and replacing it, but it didn't have the same result.
View 8 Replies
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 Replies
I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 Replies
Recently bought a 2001 Accent that has been experiencing a 'rough idle' for the last few weeks. Basically, after I've driven the car for a few minutes (from a cold engine position) and then stop at a stop light or stop sign, I can hear the engine get louder and the car starts to vibrate slightly, after I've driven for about 15 minutes at higher speeds and then stop again I can actually see the steering wheel shaking when I take my hands off of it. If i put the car in park when I am stopped and the engine is on, the idle calms down quite a bit. The weird part is that when I first start driving the car in the morning, the rough idle problem doesn't happen until about 5 minutes of steady driving - so when the engine is colder I don't experience the problem, The problem is not that serious, and Ive already brought it into a dealer who cleaned out fuel injection, gave me a major tune up and replaced all the spark plugs, but the problem still persists. I am gonna bring it back to them but they seem a bit lost to be honest. Other than this the car is driving normally when I am not idling.
View 14 Replies
i recently changed my engine oil and filter from carquest brand to quaker state and about 500 miles later, i started having some issues like, rough idle and loud ticking and bottom engine noise. is that just a coincidence or any problems with this oil? 1.6L D.O.H.C.
View 2 Replies
1991 Buick Regal, 3800 V6
Having a rough idle on a cold start. After some research and closer inspection of the vehicle, I'm quite certain I have at least one leaking injector that is flooding a cylinder and causing the car to misfire on a cold start. I'm also not at the gas mileage I should be at.
So I'm wondering, is fuel injector replacement as straightforward of a job as it looks? Any major issues I could run into in doing a replacement?
I'm planning on replacing all six injectors (I can get them for $50 each buying online with a discount code), but given that the vehicle is so old am I better off just replacing the faulty ones? I'm assuming pulling the spark plugs and seeing which cylinder is wet will tell me which I need to replace.
And one more question: Is there a way to depressurize the fuel system when I park the car for the night, thus preventing fuel (or most of it) from leaking into the engine until I get this fixed? I've read that just unscrewing the gas cap can depressurize the system.
View 14 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
